KODAK SMILE PRINTER - Instant Digital Printer Manual

INTRODUCTION

Thank you for purchasing the KODAK SMILE Instant Digital Printer. This User Guide is intended to provide you with guidelines to ensure that operation of this product is safe and does not pose risk to the user. Any use that does not conform to the guidelines described in this User Guide may void the limited warranty.
Please read all directions before using the product and retain this guide for reference. This product is intended for household use only. It is not intended for commercial use.
This product is covered by a limited one-year warranty. Coverage is subject to limits and exclusions. See warranty for details.

SPECIFICATIONS

• Dimensions: 4.625' L x 3.188' W x 0.938' H (11.75 x 8.15 x 2.5 cm)
• Weight: 7.2 oz (204 g)
• Colors Available: Black/White, White/Yel-low, Blue, Green, Red
• Battery Capacity: 700mAh
• Battery Type: Lithium-polymer
• Prints Per Charge: ~40
• Supported Photo Paper: KODAK ZINK 2' x 3' sticky-back photo paper

BOX CONTENTS

KODAK SMILE Instant Digital Printer
Starter Pack of KODAK ZINK Paper
User Guide

SAFETY PRECAUTIONS

• Do not attempt to disassemble this device for any reason.
• Never leave your printer or the ZINK® paper in an area that might become extremely hot or where it will be exposed to direct sunlight for a long time. This can cause your printer to overheat or suffer other problems.
• Don't get it wet! If you need to clean your printer, use a soft cloth that's been slightly dampened with water or rubbing alcohol, and gently wipe away any dirty spots. Don't submerge the whole thing in water, ever.
• Be careful with your printer. Try not to drop it, or shake it violently. The inside of the printer has a lot of very small parts that could break if they are jostled around too much.
• Do not use products such as alcohol, gasoline, diluent, or any other organic solvent when cleaning or attempting to clean this product.
• Do not use this device in an environment where it will be exposed to heavy dust or humidity/moisture.
• Do not use this printer while bathing or in a shower.
• Do not place or charge the printer where it can fall or be pulled into a tub or sink.
• Do not place, drop, or submerge the printer in water or any other liquid.
• If the printer somehow falls into water despite you taking all of the above precautions, please do not reach into the water to retrieve it, especially if it is charging. If it is charging, unplug it immediately and then retrieve it.
• Take care that objects do not fall and liquids are not spilled onto the printer.
• This printer absolutely will not work without downloading the ANDROID or iOS application. If you do not have an ANDROID phone or an IPHONE, unfortunately, this printer will not work for you.

PRODUCT OVERVIEW

LEDs Indicator

IDLE		SOLID WHITE
ERROR		SOLID RED
DATA TRANSFER		BLINKING BLUE
NO PAPER		BLINKING RED
PRINTING		BLINKING WHITE

GETTING READY FOR USE

Charge the SMILE

Before using the printer, connect it to the charger by plugging the micro USB cable into the designated micro USB charging port on the side and allow it to fully charge.
If the red indicator LED light is flashing, this means that the battery is low and you should plug the printer in for it to recharge. While the printer is charging, the indicator LED will be a solid red light. Once the process has completed, the indicator LED will change to a solid green light.

Load the Paper

Load your ZINK paper into the printer: Follow the steps below to quickly and easily get your new printer loaded with ZINK stickyback paper so you can start printing photos!

1. Open the paper tray in the back by removing the tray cover at the rear of the device.
   
   
2. Load the blue calibration sheet in with the barcode facing down. Place the other plain sheets on top with the glossy side facing you. Try to avoid touching the glossy side so you don't get fingerprints on it.
   
   
3. When you print your first photo after loading the ZINK paper, the blue calibration sheet will be slowly ejected from the printing slot. Your photo will print after the calibration sheet finishes.

Download the App

Download the KODAK SMILE App from the APPLE APP STORE or GOOGLE PLAY. You will need the app installed on your phone for the printer to work.

Power it On/Off

1. To turn the printer on, slide the small ridged panel away from the center. This will cause the printing slot to pop up and the LED light strip to illuminate.
   
2. To turn the printer off, simply press down the pop-up printing slot.
   

PRINTING PICTURES WITH KODAK SMILE

1. Turn the printer on by sliding the small ridged panel away from the center.
2. Make sure BLUETOOTH on your phone is enabled.
3. Open up the KODAK SMILE App from your phone, follow the instructions to pair your printer with the app, and start using your new KODAK SMILE printer!

If you have trouble connecting your printer from the application, try following these steps instead:

1. Access your phone's BLUETOOTH settings, usually found under the general Settings menu.
2. Make sure the printer is on first, and then allow your phone to scan for new devices.
3. You will see "KODAK SMILE XX:XX" appear in the BLUETOOTH list. The X's will be replaced with specific letters and numbers which correspond to your specific printer.
   Tap on it to start pairing.
4. After a couple of seconds, your phone should say "paired".

In Case of Paper Jam

If the printer jams while attempting to print, follow these steps to resolve the issue:

1. Use a small pin/needle/paper clip to pressthe reset button on the side of the printer next to the charging port.
   
2. When the reset process finishes, it should clear the paper jam.

Your KODAK SMILE printer is also equipped with a special release on the top panel to retrieve paper in case of paper jams.

NOTE: Manually removing paper from the printer head is not recommended and should only be done once you've tried resetting the printer in the way recommended above. Please be advised that removing paper in this manner can damage the printer head, and you should be extraordinarily careful while doing this.

1. Hold the printer with the ridged panel toward you. Make sure the top panel is closed and the printer is off.
2. Press down gently, but firmly, with both thumbs in the center of the panel (right about where the KODAK logo is found).
   
   
3. Push the panel away from you. It should lift off, exposing the paper in the printing area.
4. As gently as possible, try to remove the jammed paper and replace the panel by sliding it back into place until it clicks. DO NOT YANK THE PAPER.
   

Documents / Resources

References

• App Store - Apple
• Google Play

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download KODAK SMILE PRINTER - Instant Digital Printer Manual