Advertisement
The STAR1000 is a high capacity single channel commercial access control receiver for commercial door operators, and dry contact triggered devices. The STAR1000 is compatible with Security+ 2.0™ remote controls and wireless keyless entries, Security+ 2.0™ Passport and Passport Lite remote controls. This receiver is compatible with HomeLink®. For programming or compatibility information visit www.homelink.com. The receiver capacity is 1,000 devices and can be any combination of remote controls and wireless keyless entries. The receiver is watertight according to IPX44 specification.
To prevent possible SERIOUS INJURY or DEATH from electrocution:
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED.
When a receiver is used to activate a commercial door opener, a reversing edge MUST be installed on the bottom of the door. Failure to install a reversing edge under these circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door.
The STAR1000 user interface consists of a 22 character by 5 line LCD display, 3 "soft keys", Down/Up arrows and a numeric keypad.
Scroll Indicator If more than 3 options exist, a scroll indicator appears on the left margin of lines 2, 3, and 4. The scroll indicator shows the relative position within the list.
Antenna Connection
For the direct antenna or the antenna extension kit.
LCD Screen
System programming and status display.
"SOFT" Keys
Soft key functions are defined by the label on line 5 of the display. The functions change according to the menu selection.
Down/Up Keys
For navigation in the menus.
Numeric Keypad
Numeric data is entered through the numeric keypad.
The receiver has the ability to learn a combination of remote control transmitters and keyless entries up to 1,000 devices. See a complete list of compatible accessories. Audible and visual warnings occur when the receiver capacity is exceeded. After 30 seconds of inactivity, the receiver times out and the LiftMaster logo is displayed.
Select "UNLOCK" and enter the PIN to continue.
Initial PIN set up:
The PIN restricts access to authorized administrators only. If you omit this step, anyone will be able to program the receiver. Upon initial power up, the system firmware revision is displayed for 5 seconds followed by the LiftMaster ® logo. When a key is pressed, "CREATE PIN?" is displayed.
The table below describes the commands used to program the receiver.
MAIN MENU | COMMAND | DESCRIPTION | |
LEARN MENU | LEARN DEVICE | Program a device to the receiver. | |
BLOCK LEARN DEVICE | Block program a range of devices to the receiver. | ||
LEARN TO LOC # | Program a device to a 4-digit number location. | ||
DELETE MENU | DELETE DEVICE | Delete a specified device that has been programmed to the receiver. | |
DELETE ALL DEVICES | Delete all programmed devices. | ||
SUSPEND MENU | SUSPEND DEVICE | Temporarily disables the function of a specified device that has been programmed to the receiver. | |
SUSPEND ALL DEVICES | Temporarily disables the function of ALL devices programmed to the receiver. | ||
UNSUSPEND DEVICE | Re-enable the function of a suspended device. | ||
UNSUSPEND ALL DEVICES | Re-enable the function of ALL suspended devices. | ||
QUERY MENU | LOC # USED | Displays a range of used locations starting from a specified location. | |
LOC # AVAILABLE | Displays a range of empty locations starting from a specified location. | ||
LOC # SUSPENDED | Displays a range of suspended locations starting from a specified location. | ||
SETTINGS | CHANGE PIN | Change the 6-digit PIN number for the receiver. | |
DEALER INFO | Display and edit the dealer 11-digit contact phone number. | ||
FIRMWARE VERSION | Displays the current firmware version. | ||
BEEP | Turn the audible feedback on or off. | ||
MEMORY | DUPLICATE MEMORY | Creates a memory backup. A backup memory module must be installed. | |
RESTORE MEMORY | Restores a memory backup from a memory module. NOTE: Content of memory backup module will over-write any information already stored in the receiver memory. | ||
RELAY | Sets the relay activation time from.25 to 1 second. | ||
CONTRAST | Press Down or Up arrows to adjust LCD contrast. | ||
LANGUAGE | Sets menu language: English (Default), Spanish, and French. | ||
FREQUENCY | Sets frequency of Receiver from 315 MHz (Default) to 390 MHz or 433.92 MHz. | ||
FACTORY DEFAULT | Reset receiver to factory default settings. |
The receiver emits a series of audible beeps to signal programming and error events. The table at right lists all of the events and their audible notifications. The On/Off column indicates that the audible notification for the event may be disabled in the BEEP SETTINGS menu.
EVENT | AUDIBLE NOTIFICATIONS | ON/OFF |
Key press | Single | YES |
Successful Add | Double | |
Successful Delete | Triple | |
Successful Suspend | Double | |
Successful Unsuspend | Double | |
Master PIN entry error | Long | |
Programming error | Long | |
Location out of range | Long | |
Generic Success | Double | |
Generic Error | Long | |
Received unknown Tx | Slow | YES |
Received known Tx | Double | YES |
Received known suspended Tx | Long | YES |
System Capacity | 1000 devices |
Voltage/Current | 9 - 30 Volts AC, 9 - 42 Volts DC 9 - 42 VDC 70 mA Max. 9 - 30 VAC 50 - 60 Hz 150 mA Max. |
Surge Suppression | 6.0 kV Min. |
Operating Temp Range | -40°C to +65°C @ 50% Rh, -40°F to +149°F @ 50% Rh |
Storage and Shipping Temp Range | -40°C to +85°C @ 50% Rh |
Code Format | Security+: 2.0™ Only |
Relay Contact Rating | 1 amp @ 24V AC/DC |
Remote Controls* | 892LT, 894LT, 891LM, 893LM, 890MAX, 893MAX, PPV3M, PPK3M, PPK3PHM, PPLV1-xxx, PPLK1-xxx, PPLK1PH-xxx |
Keypads* | 877LM, 877MAX, and 878MAX |
Antenna Extension Kits: | |
15' Extension Kits | 86LM |
25' Extension Kits | 86LMT |
24VAC Transformer for screw terminals | 95LM |
REPAIR PARTS
Antenna | K76-36681 |
Mounting Bracket | K13-36651-1 |
* NOTE: IF CHANGING THE FREQUENCY OF THE RECEIVER FROM THE DEFAULT 315 MHZ TO 390 MHZ, ONLY THE FOLLOWING REMOTES/ KEYPADS HAVE THE CAPABILITY TO BE 390 MHZ SECURITY+2.0: 892LT, 894LT, 893MAX, PPV3M REMOTES AND 878MAX KEYPAD.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions:
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800-528-2806
© 2023, The Chamberlain Group LLC.
All Rights Reserved
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download LiftMaster STAR1000 - Commercial Access Control Receiver Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the STAR1000 that isn't answered in the manual? Leave your question here.