Eureka NEU180 Series - Upright Vacuum Cleaner Manual

Where to find important device information

Keep this information

Write the model, type and serial number, Date of purchase (keep your receipt), Model number and type, Serial number.

Find these numbers on a label on the middle back side of the vacuum cleaner. Refer to these numbers when ordering parts and accessories or if service is needed.

This Owner's Guide provides important instructions to prolong the life of your Eureka vacuum cleaner.

Registration:
To register your product visit www.eureka.com and click on the 'Register Your Product' link in the top right corner.

Inspection:
Carefully unpack and inspect your new Eureka vacuum cleaner for shipping damage. Each unit is tested and thoroughly inspected before shipping. For instructions regarding any shipping damage, call the Eureka Customer Service HELPLINE at 1-800-282-2886 immediately.

Follow caution information wherever you see this symbol.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER

To reduce the risk of fire, electric shock, or injury:

• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call the Eureka Customer Service HELPLINE at 1-800-282-2886.
• Do not pull or carry by cord. Do not use cord as a handle. Do not close a door on cord or pull cord around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any objects into openings. Do not use with any openings blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not place vacuum cleaner on furniture or stairs as the brush roll may cause damage. Use extra care when cleaning stairs. Place vacuum cleaner on floor with the handle in storage position while using attachments.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust cup, filter and screen in place.
• 
  Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
• Store your vacuum cleaner indoors in a cool, dry area.
• Keep your work area well lit.
• Unplug electrical appliances before vacuuming them.
• 
  This product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer, and Bisphenol-A, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

SAVE THESE INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Motor
Do Not Oil the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.

What comes in the carton

Accessories may vary depending on which model was purchased.
Eureka Customer Service HELPLINE 1-800-282-2886

How to assemble your device

Vacuum cleaner with dust cup.

Slide handle into top of vacuum cleaner. Push down until it clicks.

Insert bent end of hose into opening at back of dust cup. Twist hose clockwise to lock.

Store accessories on back of vacuum cleaner.

Loop hose over hose retainer.

Push loose end of hose securely onto hose inlet.

Align upper and lower cord hooks and press to snap in place. Upper cord hook should rotate freely.

Wrap cord onto upper and lower cord hooks.

Store turbo brush on front of handle. Align brush opening with slot and push to snap tool into clip.
Select models only (NEU182-NEU188 except NEU182A)

How to identify parts of your device

Headlights are included on select models only (NEU186-NEU188).
Accessories may vary depending on which model was purchased.

How to use your appliance

Plug power cord into outlet.

Turn height adjustment knob to adjust from bare floors to high pile carpet.

Step on power switch to turn vacuum cleaner on. Step on again to turn off.

Step on handle release to lower handle into position for vacuuming floors.

Empty dust cup after every use

Press release button and lift off dust cup.

To empty debris, press lever to release bottom lid.

How to use accessories

When using tools, always place handle in upright position. Make sure vacuum cleaner is turned off while attaching tools.

• Place vacuum in upright position.
• Turn height adjustment knob to highest position.
• Pull up on hose connection to release hose end from hose inlet.
  
• Push end of hose into top of handle and twist clockwise until it clicks.
  
• Press handle release latch and pull out handle with wand.
  
• To attach accessories, push desired tool onto end of wand.
  
• To use accessories without handle and wand, push desired tool directly onto end of hose.
  
• When finished using accessories, twist hose counterclockwise and pull off handle. Slide handle into top of vacuum cleaner and push down until it clicks. Push loose end of hose securely onto hose inlet. Store tools on vacuum cleaner back.

Crevice tool (NEU180-NEU187) –
Use for baseboard edges, corners, detailing chairs, sofas, dryer vents and tight spaces.

Upholstery tool (NEU180-NEU187) –
Use for furniture, chairs, sofas and mattresses.

2-in-1 upholstery tool (NEU188) –
Use brush to vacuum upholstered surfaces or pick up debris. Use felt portion to clean delicate surfaces. Press thumb release and lift brush up and out of the way.

Flexible telescoping crevice tool (NEU188) –
Press button and pull to extend tool to desired length. To use brush, pull to swivel into position. Use for baseboards, crevices and tight spaces.

Dusting brush (NEU180-NEU187) –
Use for furniture, drapes, blinds, drawers and vents.

Turbo brush (NEU182-NEU188 except NEU182A) –
Use to remove pet hair from stairs, carpet and upholstery.

Accessories may vary depending on which model was purchased.

How to maintain dust cup and filters

Dust cup

Empty after each use

Press release button and lift off dust cup.

Hold dust cup over wastebasket and press lever to release bottom lid. Debris will empty.

Close bottom lid until it clicks.

Washable dust cup filters

Clean monthly

Pull dust cup latch to lift up dust cup lid.

Lift out foam filter and shake off dust. Rinse foam filter and dry THOROUGHLY.

Grip tabs and lift out filter screen. Twist bottom of filter screen counterclockwise to unlock and pull apart. Shake off dust. Rinse screen and dust cup. Dry all THOROUGHLY. Reassemble screen; twist clockwise to lock.

Align tab on filter screen with slot on back of dust cup and drop into position.

Reinstall foam filter.

Close cover until it clicks.

Never operate vacuum cleaner without foam filter, filter screen and dust cup in proper position.

How to clear a blockage

Make sure vacuum is turned off and power cord is unplugged.

If vacuum is not cleaning floors, or if no suction at end of hose, check to be sure air path is not blocked.

• Press release button and lift off dust cup.
  
• Empty debris. Hold over wastebasket and press lever to release bottom lid.
  
• Check filter and filter screen. Remove any debris and shake off dust. (See maintenance instructions)
• Loosen end of hose.
• Use a rod or similar blunt implement to clear a blockage in wand or hose. Flex hose to loosen debris. Use caution if there is any risk that glass or nails could have become imbedded in hose.
  
• Use finger to check for debris in air path.
  
• Reinstall filter and filter screen inside dust cup and position dust cup onto vacuum cleaner.

Never operate vacuum ! cleaner without foam filter, filter screen and dust cup in proper position.

How to maintain brushroll

Make sure vacuum is turned off and power cord is unplugged.

• Step on handle release to lower handle.
  
• Turn vacuum face down on floor.
• To avoid unnecessary service calls, check brushroll for debris.
• Use scissors to clip heavy threads or strings.
  

How to maintain turbo brush

Select models only (NEU182-NEU188 except NEU182A)

Grasp collar and twist to unlock cover. Lift cover up.

With cover open, use figers or small brush to clear accumulated pet hair from bristles.

Close cover and twist collar to lock.

How to replace brushroll or belt

Make sure vacuum is turned off and power cord is unplugged.

• Step on handle release and lay vacuum cleaner face down.
• Use Phillips screwdriver to remove 6 screws from brushroll cover (Fig. 1). Lift off cover. Refer to Fig. 7 for location of screws.
  
• Rotate right end of brushroll and lift out (Fig. 2).
  
• Lift out left end of brushroll.
• To replace belt, position new belt around motor shaft (Fig. 3).
  
• Loop new belt around brushroll shaft at left end of brushroll (Fig. 4).
  
• To reposition brushroll into base, pull belt down and insert left end of brushroll first. Align brushroll end cap with slot so it fits into position (Fig. 5). Press right end of brushroll into position.
  
• To replace brushroll cover, align slot on cover with tab (Fig. 6) and snap cover into place. Replace 6 screws (Fig. 7).
  
  

Problem solving

Make sure vacuum is turned off and power cord is unplugged.

NOTICE: Thermal cut-off
This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating.
If the vacuum suddenly shuts off, proceed as follows:

1. Push the power switch to off and unplug the vacuum.
2. Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum.
3. After the 30 minute period, plug the vacuum back in and turn on the switch.

If the vacuum still does not work, call the Eureka Customer Service HELPLINE at 1-800-282-2886.

Eureka stands by our Clean Promise seal.
Learn more at www.eureka.com/cleanpromise

www.eureka.com

Documents / Resources

References

• Eureka - Vacuums for all your cleaning needs
• http://www.p65warnings.ca.gov

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Eureka NEU180 Series - Upright Vacuum Cleaner Manual