Page 1
83001 and up • This shop manual may contain attachments and optional equipment that are not available in your area. Please consult your local Komatsu distributor for those items you may require. Materials and specifications are subject to change without notice. •...
Page 2
CONTENTS No. of page GENERAL ................. 01-1 STRUCTURE AND FUNCTION ........10-1 TESTING AND ADJUSTING ........... 20-1 DISASSEMBLY AND ASSEMBLY ........30-1 MAINTENANCE STANDARD .......... 40-1 OTHERS................90-1 00-2 D21A, P-8 Find manuals at https://best-manuals.com...
Page 3
LIST OF REVISED PAGES The affected pages are indicated by the use of the Mark Indication Action required following marks. It is requested that necessary actions be taken to these pages according to the table below. fi Page to be newly added ‡...
Page 4
LIST OF REVISED PAGES Time of Time of Time of Time of Time of Mark Page Mark Page Mark Page Mark Page Mark Page revision revision revision revision revision 20-202 20-242 20-417 30-13 30-53 20-203 20-418 30-14 30-54 20-204 20-301 20-501 30-15 30-55...
Page 5
LIST OF REVISED PAGES Time of Time of Time of Time of Time of Mark Page Mark Page Mark Page Mark Page Mark Page revision revision revision revision revision 40- 5 90-140 40- 6 90-101 90-141 40- 7 90-102 90-142 40- 8 90-103 90-143...
Proper service and repair is extremely important for safe machine operation. The service and repair techniques recommended by Komatsu and described in this manual are both effective and safe. Some of these techniques require the use of tools specially designed by Komatsu for the specific purpose.
Page 7
SAFETY SAFETY NOTICE PRECAUTIONS DURING WORK 19.Be sure to assemble all parts again in their origi- nal places. 11.When removing the oil filler cap, drain plug or Replace any damaged parts with new parts. hydraulic pressure measuring plugs, loosen • When installing hoses and wires, be sure them slowly to prevent the oil from spurting out.
Page 8
FOREWORD GENERAL FOREWORD GENERAL This shop manual has been prepared as an aid to improve the quality of repairs by giving the serviceman an accurate understanding of the product and by showing him the correct way to perform repairs and make judge- ments.
Page 9
DISTRIBUTION AND UPDATING Any additions, amendments or other changes will be Symbol Item Remarks sent to KOMATSU distributors. Get the most up-to- date information before you start any work. Special safety precautions Safety are necessary when per- forming the work.
Page 10
FOREWORD HOISTING INSTRUCTIONS HOISTING INSTRUCTIONS HOISTING Slinging near the edge of the hook may cause k Heavy parts (25 kg or more) must be lifted the rope to slip off the hook during hoisting, and a serious accident can result. Hooks have max- with a hoist, etc.
Page 11
FOREWORD METHOD OF DISASSEMBLING, CONNECTING PUSH-PULL TYPE COUPLER METHOD OF DISASSEMBLING, CONNECTING PUSH-PULL TYPE COUPLER k Before carrying out the following work, release Type 1 the residual pressure from the hydraulic tank. For details, see TESTING AND ADJUSTING, Releasing residual pressure from hydraulic tank.
Page 12
FOREWORD METHOD OF DISASSEMBLING, CONNECTING PUSH-PULL TYPE COUPLER Type 2 Type 3 1) Hold the mouthpiece of the tightening portion 1) Hold the mouthpiece of the tightening portion and push body (2) in straight until sliding pre- and push body (2) in straight until sliding pre- vention ring (1) contacts contact surface a of vention ring (1) contacts contact surface a of the hexagonal portion at the male end.
★ The recommended coating materials such as adhesives, gasket sealants and greases used for disassembly and assembly are listed below. ★ For coating materials not listed below, use the equivalent of products shown in this list. Category Komatsu code Part No. Q'ty Container Main applications, features •...
Page 14
FOREWORD COATING MATERIALS Category Komatsu code Part No. Q'ty Container Main applications, features • Used as lubricant for sliding portion LM-G 09940-00051 60 g (to prevent from squeaking). Molybdenum • Used to prevent seizure or scuffling disulphide of the thread when press fitting or...
FOREWORD STANDARD TIGHTENING TORQUE STANDARD TIGHTENING TORQUE STANDARD TIGHTENING TORQUE TABLE (WHEN USING TORQUE WRENCH) ★ In the case of metric nuts and bolts for which there is no special instruction, tighten to the torque given in the table below. Tightening torque Thread diameter Width across...
Page 16
FOREWORD STANDARD TIGHTENING TORQUE TABLE OF TIGHTENING TORQUES FOR SPLIT FLANGE BOLTS ★ In the case of split flange bolts for which there is no special instruction, tighten to the torque given in the table below. Thread diameter Width across flat Tightening torque 59 –...
Page 17
FOREWORD STANDARD TIGHTENING TORQUE TIGHTENING TORQUE FOR 102 ENGINE SERIES 1) BOLT AND NUTS Use these torques for bolts and nuts (unit: mm) of Cummins Engine. Thread diameter Tightening torque 10 0 2 1.02 0 0.20 24 0 4 2.45 0 0.41 43 0 6 4.38 0 0.61 77 0 12...
Page 18
FOREWORD ELECTRIC WIRE CODE ELECTRIC WIRE CODE In the wiring diagrams, various colors and symbols are employed to indicate the thickness of wires. This wire code table will help you understand WIRING DIAGRAMS. Example: 5WB indicates a cable having a nominal number 5 and white coating with black stripe. CLASSIFICATION BY THICKNESS Copper wire Current...
FOREWORD CONVERSION TABLE CONVERSION TABLE METHOD OF USING THE CONVERSION TABLE The Conversion Table in this section is provided to enable simple conversion of figures. For details of the method of using the Conversion Table, see the example given below. EXAMPLE •...
Page 24
FOREWORD CONVERSION TABLE Temperature Fahrenheit-Centigrade Conversion ; a simple way to convert a Fahrenheit temperature reading into a Cen- tigrade temperature reading or vice versa is to enter the accompanying table in the center or boldface col- umn of figures. These figures refer to the temperature in either Fahrenheit or Centigrade degrees.
Page 25
FOREWORD UNITS UNITS In this manual, the measuring units are indicated with Internatinal System of units (SI). As for reference, conventionally used Gravitational System of units are indicated in parentheses { Example: N {kg} Nm {kgm} MPa {kg/cm kPa {mmH kPa {mmHg} kW/rpm {HP/rpm} g/kWh {g/HPh}...
Page 31
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...