Selecting Languages - Milwaukee 3712 Operator's Manual

Using Sleep Mode
Sleep Mode can be used to conserve the rotary laser
battery without disturbing laser setup.
1. To ENTER Sleep Mode, select the Sleep icon from
the main menu.
2. Press the OK button, this will send the laser to
"sleep" mode.
NOTE: The laser head will stop rotating and the
laser diode will turn off. The laser will retain its
current position and settings and will resume when
Sleep Mode is exited. If the laser is asleep for more
than 4 hours, the laser will automatically shut off.
3. To EXIT Sleep Mode, press the OK button to
"wake" the laser. The laser will "wake", and func-
tion with the same settings. If the Remote/Receiver
is powered off, it will re-pair to the laser when pow-
ered on, and the sleep menu will re-open with the
option to "wake" with the press of the OK button.
Adjusting the Volume
• Select the Volume icon from the main menu, and
press the OK button.
• Use the up/down arrows to toggle between high
(>95 dBA), low (72 - 90 dBA), and off. When toggling,
a sample tone will play to demonstrate the currently
selected setting. Press OK to confirm selection.
The icon on the status bar will update to show the
current selection.
Setting the Units of Measure
1. Select the Units icon from the main menu, and
press the OK button.
2. Choose from the measurement options of;
millimeters, inches (decimal), inches (fractions),
and feet using the arrow buttons.
3. Press the OK button, and the measurement setting
will reflect in the main menu and will update in the
Direct Read Out.
Setting Accuracy
• Select the Accuracy icon in the main menu and press
the OK button. Use the up/down arrows to toggle
between tolerance levels: ultra-fine, fine, medium,
coarse, and ultra-coarse. The icon on the display
will update to show current selection. See the table
below for receiver deadband accuracy based on unit
and accuracy settings.
Remote/Receiver Accuracy
in. in.
mm
(Dec.) (Frac.)
0.5 0.02 1/32
1 0.04 1/16
2 0.08 1/8
3 0.12 1/4
5 0.2 1/2
ft. Levels
Level
0.001
Level
0.003
Level
0.006
Level
0.010
Level
0.016
Using the Offset Mode
1. Select the offset icon from the main menu.
2. Press the OK button to continue.
3. Ensure the laser beam is in front of the Remote/
Receiver.
4. The Remote/Receiver will display the offset dis-
tance based on the current sensing location of the
beam on the sensor.
5. Press the OK button to confirm the setting. The
Direct Read Out, arrow indications and LED indi-
cator will now work to direct the laser to the new
center location.
6. To reset the offset menu, re-enter the offset menu
and hold the left and right arrow buttons simultane-
ously and the offset will be reset back to 0.
NOTE: Offset is not compatible with Center Lock
or Center Find. Initiating these functions will reset
offset to 0.
Pairing the Remote/Receiver with the
It is recommended to use the corresponding laser
stated in the "specifications" section.
1. Ensure both the laser and remote/receiver are
completely turned off.
2. To turn ON the remote/receiver, press the power
button.
3. To turn ON the laser, press the power button.
4. Ensure auto-leveling is complete before pairing the
remote/receiver to the laser. The Leveling LED will
be solid green and the laser head will start to rotate
5. To PAIR the remote/receiver with the laser, select
the pairing icon in the main menu of the remote/
receiver, then press and hold the pairing button on
the laser. The Pair Indicator LED will flash white
while the tool searches for the remote/receiver.
When the device connection is successful, an
audible tone will sound, and the Pair Indicator LED
will remain solid white.
NOTE: Only 1 laser and 1 remote/receiver can be
paired at a time to the laser. If the connection fails
after 30 seconds, the Pair Indicator LED will stop
flashing, and the tool will beep multiple times to indi-
1
cate a failure. The operation will need to be repeated.
2
On initial startup, use the up/down arrows keys to
select the desired language, then press the OK but-
3
ton to confirm. To change to a different language, go
to the language icon located in the main menu, and
press the OK button. Select the desired language,
4
and press the OK button again.
Using the Information Screen
5
The information screen is useful for tracking operat-
ing hours, drop events detected, and temperature
events detected.
1. Select the information icon from the main menu.
2. Press the OK button to continue.
3. Event log can be reset for tracking purposes by
pressing the left and right arrow buttons simultane-
ously when in the information menu.
6
Rotary Laser

Selecting Languages