Table of Contents
Advertisement
Available languages
Available languages
ASSEMBLY
Attaching the Clamp
The clamp is an optional piece that can be attached
to the Remote/Receiver. The clamp can be used with
grade rods, and pieces of lumber up to 2.5" thick.
1. To attach the clamp to the receiver, align the
attachment posts on the clamp with the clamp
connection feature on the back of the receiver.
2. Align the screw on the back, and turn the knob
clockwise to tighten into place.
3. Attach the clamp to the workpiece by turning
the clamping knob counterclockwise to open the
clamping jaws. To tighten the clamp to the work-
piece, turn the clamping knob clockwise. Ensure
the clamp is snug before operation.
4. To remove the clamp from the workpiece, turn the
clamping knob counterclockwise until the clamp
jaws release from the workpiece. To remove the
clamp from the receiver, turn the clamping at-
tachment knob counterclockwise and remove the
clamp from the back of the receiver.
Changing the Batteries
Only use alkaline batteries. Do not use zinc-carbon
batteries. If the receiver will not be used for a long
time, remove the batteries to protect against corro-
sion. Change batteries when the fuel gauge shows
low batteries.
To change the batteries:
1. To open the battery door, turn the latch clockwise
to the unlocked position and then open the door.
2. Remove the old AA batteries, and dispose of
them properly.
3. Insert two AA batteries according to the +/- polarity
marked in the compartment.
4. To close the battery door, close the door and
then turn the latch counterclockwise to the locked
position.
Fuel Gauge
To determine the amount of charge left in
the batteries, turn the tool ON. The display
will show the battery charge: Full, 3/4, 1/2
and low battery warning. Battery life may
vary by brand/age. Replace the batteries
as soon as possible.
OPERATION
To reduce the risk of injury or tem-
WARNING
porary effects on vision, do not
look directly into the laser when it is on.
Use of controls or adjustments or
CAUTION
performance of procedures other
than those specified herein may result in hazard-
ous radiation exposure.
Perform the Accuracy Field Check
NOTICE
procedure immediately upon unboxing
of each new Remote/Receiver and before expo-
sure to jobsite conditions. See "Accuracy Field
Check" for information. Should any deviation from
listed product accuracy be found, please con-
tact a MILWAUKEE service facility. Failure to do so
could result in rejection of warranty claim.
Turning the Remote/Receiver ON/OFF
1. To turn ON, press the Power button until the laser
Remote/Receiver beeps. The icons and LED will
flash for 1 second, then return to the home screen.
NOTE: On initial startup, use the up/down arrows
to select the desired language, then press OK to
confirm. The backlight will illuminate after any but-
ton press or when a laser beam is detecting on the
sensor. The backlight will stay on for 15 seconds.
The timer will reset every time a button is pressed
or when a laser is sensed for the first time (i.e. it
wont stay on if a laser stays on the sensor, but if a
laser moves off then back on, the timer will reset).
2. To turn OFF, long press the power button for more
than 1 second. Auto shut-off will occur if there are
no button presses and no laser beam detected
for 15 minutes.
NOTE: The laser and Remote/Receiver are
independent of one another. A power button
press on the Remote/Receiver will power off the
Remote/Receiver, and the laser will remain on.
Center Find
Center Find feature is only compatible with certain
RPM's and accuracy settings and is not compatible
with Channel Link. Some settings may automatically
change when this function is being used. Press the
OK button to clear any setting change notification of
the Remote/Receiver.
1. Place the paired Remote/Receiver in the desired
location.
NOTE: The Remote/Receiver must be aligned with
the Y axis of the rotary laser. For best results, use
the iron sight on top of the laser to align directly
with the Remote/Receiver sensor.
2. Press the Center Find button on the Remote/
Receiver or navigate the Center Find icon in the
main menu and press the OK button. The laser
will begin to slope in the Y axis searching for the
Remote/Receiver.
3. Once the laser detects the Remote/Receiver, the
Remote/Receiver will show "center found" at the
top of the screen.
NOTE: If the center is not found, the Remote/Receiver
will display "not found". Press the OK button, and the
Remote/Receiver will go to the main menu, and the
laser will start the self-leveling procedure. Select the
Center Find icon from the menu, and try steps 1 - 3
again until the center is found.
4
Advertisement
Table of Contents
