Traxxas 1/16 E REVO VXL BRUSHLESS Owner's Manual page 17

USING THE RADIO SYSTEM
The TQi Radio System has been adjusted at the factory for correct
operation with your model. The adjustment should be checked before
running the model, in case of movement during shipping. Here's how:
1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).
2. Elevate the model on a block or a stand so that all the tires are
off the ground. Make sure your hands are clear of the moving
parts of the model.
3. Plug the battery pack in the model into the speed control.
4. The on/off switch is integrated into the speed control. With the
transmitter on, press and release the EZ-Set button (.25 seconds).
The LED will shine RED (see note, below). This turns the model
on. To turn the VXL-3m off, press and hold the EZ-Set button until
the LED turns off (.5 seconds). Note: If the LED shines green, Low-
Voltage Detection is activated. This may cause poor performance
from the included NiMH battery pack. The default factory setting
is for Low-Voltage Detection to be disabled (LED shines red).
Make sure to turn the Low-Voltage Detection on when using LiPo
batteries. Never use LiPo batteries while Low-Voltage Detection
is turned off. See page 20 for more information.
5. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak batteries.
6. When looking down at the
model, the front wheels
should be pointing straight
ahead. If the wheels are turned
slightly to the left or right,
turn off TSM (see page 18) and
slowly adjust the steering trim
control on the transmitter until they are pointing straight ahead;
then, return the Multi-Function knob to the desired TSM setting.
7. Gently operate the throttle trigger to ensure that you have forward
and reverse operation, and that the motor stops when the throttle
trigger is at neutral. Warning: Do not apply full throttle in forward
or reverse while the model is elevated.
8. Once adjustments are made, turn off the receiver on your model,
followed by the hand-held transmitter.
TRAXXAS TQ RADIO & VELINEON POWER SYSTEM
i
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation, as described in
the previous section.
2. Have a friend hold the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Walk away from the model with the transmitter until you reach the
farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure that
the model responds correctly.
5. Do not attempt to operate the model if there is any problem with
the radio system or any external interference with your radio signal
at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the limit
of radio range. At top speeds, models can cover anywhere between
50 to 100 feet every second! It's a thrill, but use caution to keep your
model in range. If you want to see your model achieve its maximum
speed, it is best to position yourself in the middle of the truck's
running area, not the far end, so you drive the truck towards and
past your position. In addition to maximizing the radio's range, this
technique will keep your model closer to you, making it easier to see
and control.
No matter how fast or far you drive your model, always leave adequate
space between you, the model, and others. Never drive directly toward
yourself or others.
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
7,8 7,8
1/16 E-REVO VXL • 17