Table of Contents
Advertisement
24
Settings and adjustments for the DVD player (continued)
Setting sound options
(Audio Setup)
You can adjust your audio settings based on
the playback conditions or the equipment in
use.
The default setting for each menu is underlined
in the explanations below. For details, see
"Using the Setup display" on page 20.
Select the
(Audio Setup) icon in the Setup
display.
x Audio Digital Out
You can switch the methods of outputting
audio signals when you connect the following
audio devices to the DIGITAL OUT (OPTICAL)
connector on the PlayStation™2 console rear
using an optical digital cable (sold separately).
• A digital device such as a receiver (amplifier)
with a digital connector.
• An audio device with a built-in Dolby Digital
or DTS decoder.
• A DAT (Digital Audio Tape) or MD
(MiniDisc) deck. For connection details, see
page 7.
x DIGITAL OUT (OPTICAL)
Selects whether to output signal through the
DIGITAL OUT (OPTICAL) connector.
• On: Select this when you connect with an
optical digital cable (sold separately).
Normally select this option.
If you select "On", make the appropriate
settings for "Dolby Digital", "DTS" and
"MPEG".
• Off: Select this when you do not want sound
(audio signal) to be output through the
DIGITAL OUT (OPTICAL) connector.
Note
If you select "Off", you cannot set "Dolby Digital", "DTS"
or "MPEG".
x Dolby Digital
Selects the Dolby Digital signal to be output
through the DIGITAL OUT (OPTICAL)
connector.
• On: Select this option when the console is
connected to an audio device with a built-in
Dolby Digital decoder.
If the console is connected to an audio device
without a built-in Dolby Digital decoder, do
not turn this option on. If you select this
option by mistake, when you play a Dolby
Digital audio track, a loud noise (or no
sound) will come out from the speakers,
possibly hurting your ears or damaging the
speakers.
• Off: Select this option when the console is
connected to an audio device without a built-
in Dolby Digital decoder.
x DTS
Selects the DTS signal to be output through the
DIGITAL OUT (OPTICAL) connector when
you connect to the console with an optical
digital cable (sold separately).
This setting is not available during Resume Play.
• On: Select this option when the console is
connected to an audio device with a built-in
DTS decoder.
If the console is connected to an audio device
without a built-in DTS decoder, do not turn
this option on. If you select this option by
mistake, when you play a DTS audio track, a
loud noise (or no sound) will come out from
the speakers, possibly hurting your ears or
damaging the speakers.
• Off: Select this option when the console is
connected to an audio device without a built-
in DTS decoder.
x MPEG
Selects the MPEG AUDIO signals to be output
via the DIGITAL OUT (OPTICAL) connector.
• On: Select this option when the console is
connected to an audio device with a built-in
MPEG decoder.
If the console is connected to an audio device
without a built-in MPEG decoder, do not
turn this option on. If you select this option
by mistake, when you play an MPEG audio
track, a loud noise (or no sound) will come
out from the speakers, possibly hurting your
ears or damaging the speakers.
• Off: Select this option when the console is
connected to an audio device without a built-
in MPEG decoder.
x Audio Track Auto Select Mode
Gives the audio track that contains the highest
number of channels priority when you play a
DVD on which multiple audio formats (PCM,
Dolby Digital, DTS or MPEG AUDIO) are
recorded.
This setting is not available during Resume Play.
• On: Priority given
• Off: No priority given
Notes
• If you set this item to "On", the language may change
because the "Audio Track Auto Select Mode" setting
has higher priority than the "Audio" settings in
"Language Setup" (page 21).
• If you set "DIGITAL OUT (OPTICAL)" to "On" and
"DTS" to "Off" in "Audio Setup", the DTS audio track
is not played even if you set this item to "On" and the
highest-numbered audio channel is recorded in DTS
format.
• If PCM, Dolby Digital, DTS and MPEG audio tracks
have the same number of channels, the console selects
PCM, Dolby Digital, DTS and MPEG audio tracks in
this order.
• Depending on the DVD, the audio channel with
priority may be predetermined. In this case, you cannot
give priority to the Dolby Digital, DTS or MPEG format
by selecting "On".
x DVD Volume
If the audio output level of the DVD is low, you
can turn up the volume of the DVD. DIGITAL
OUT (OPTICAL) must be set to "Off" to change
this setting.
• +2: Turns up the volume (maximum).
• +1: Turns up the volume.
• Standard: Original audio volume. Normally
select this position.
Note
If you set this option to "+1" or "+2", the sound may be
distorted in places where loud sound is present. If the
sound becomes distorted, select "Standard".
Caution
If you turn up the volume too high, your ears may be
injured or the speakers may be damaged.
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
Advertisement
Table of Contents
