Table of Contents
Advertisement
NOTES
• The pairing process may take up to
one minute. If the pairing process
fails, try again.
• When
a
connected
headset
charging, it may disconnect from
the
telephone
base
and
CELL 2/HEADSET
light
on
telephone base turns off. For some
headset models, you may need to
turn on the headset and reconnect it
to the telephone base again.
Auto connection
When an active device moves within
Bluetooth range of the telephone base,
or is turned on within range, the
telephone base tries to connect to the
device. When the device moves out of
range, it is disconnected. Your device
might make a connect or disconnect
sound.
A connected device could also be
disconnected by:
• Turning off the Bluetooth device.
• Turning off the Bluetooth feature of
the device.
• Disconnecting through the telephone
base Device list. If you disconnect
through the Device list, the telephone
base will not attempt to reconnect
until your device is moved out of
range and then moves back in range
again.
Device list and connection
Up to 2 devices can be paired to the
telephone base. All paired devices are
shown on the device list. To use a paired
device, it must be connected. Both
is
Bluetooth enabled devices can be used
on a cell call at a time.
the
Once you have paired a device with the
the
telephone base, you do not need to
repeat the pairing procedure again
unless you delete the device from the
device list.
NOTE
• When connecting a Bluetooth device
to the device list, all connected devices
will be temporarily disconnected until
the procedure is complete. It may take
up to two minutes to reconnect.
Review the device list
1. Press MENU/SELECT on the telephone
base in idle mode to enter the main
menu.
2. Press
q
CID
or
p
highlight
Bluetooth,
then
MENU/SELECT.
3. Press MENU/SELECT again to select
Device list.
66
Connect/disconnect an active device
While in the device list menu, you
may connect or disconnect your active
device.
1. Press
MENU/SELECT
telephone base in idle mode to enter
the main menu.
2. Press
q
CID
highlight Bluetooth, then press
MENU/SELECT.
3. Press
q
CID
highlight Device list, then press
MENU/SELECT.
4. Press q CID or p DIR to highlight a
device, then press MENU/SELECT.
5. Press q CID or p DIR to highlight
Connect/Disconnect
is
applicable),
MENU/SELECT.
base displays Device connected/
Device disconnected. You hear a
confirmation tone.
NOTE
DIR
to
• When
your
press
connected, you are prompted to
select Disconnect. When your active
device is disconnected, you are
prompted to select Connect.
Remove a paired device
When you already have 2 devices on the
device list and you want to add another
device, you must first delete one from
the list. You can only pair 2 cell phones
on
the
or one cell phone and one Bluetooth
headset.
To remove a paired device:
or
p DIR
to
MENU/SELECT
1. Press
telephone base in idle mode to enter
or
p DIR
to
the main menu.
q
2. Press
highlight Bluetooth, then press
MENU/SELECT.
q
3. Press
highlight Device list, then press
(whichever
MENU/SELECT.
then
press
4. Press q CID or p DIR to highlight
The
telephone
the desired device, then press
X/DELETE.
-OR-
• Press q CID or p DIR to highlight
the desired device, then press
MENU/SELECT.
active
device
is
• Press q CID or p DIR to
highlight Remove, then press
MENU/SELECT.
5. The telephone base displays Remove
Headset X? (Headset X represents
the device name of your Bluetooth
headset). Press MENU/SELECT to
confirm. The telephone base displays
Device removed from device list
and you hear a confirmation tone.
67
on
the
p DIR
CID
or
to
p DIR
CID
or
to
Advertisement
Table of Contents
