Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Operating Instructions
Air Conditioner
Model No.
Indoor Unit
S-1821PT3H-8
S-2430PT3H-8
S-3448PT3H-8
ACXF55-32051_SS1021-1.indb 1
ACXF55-32051_SS1021-1.indb 1
Outdoor Unit
U-21PR1H5
U-30PR1H5
U-43PR1H5
U-48PR1H5
U-43PR1H8
U-48PR1H8
Hướng dẫn sử dụng
Máy điều hòa không khí
Trước khi bật thiết bị, vui lòng đọc kỹ hướng dẫn sử dụng này
và giữ lại để tham khảo cho những lần sau.
Trước khi lắp đặt, người lắp đặt nên:
Đọc hướng dẫn lắp đặt và yêu cầu khách hàng cất giữ bản
hướng dẫn để tham khảo sau này.
Operating Instructions
Air Conditioner
Before operating the unit, please read these operating
instructions thoroughly and keep them for future reference.
Before installation, the installer should:
Read the Installation Instructions, then request the customer
keep them for future reference.
2-21
22-41
ACXF55-32051
13/10/2021 6:32:20 PM
13/10/2021 6:32:20 PM

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic S-1821PT3H-8

  • Page 1 Operating Instructions Air Conditioner Model No. Indoor Unit Outdoor Unit S-1821PT3H-8 U-21PR1H5 S-2430PT3H-8 U-30PR1H5 S-3448PT3H-8 U-43PR1H5 U-48PR1H5 U-43PR1H8 Hướng dẫn sử dụng 2-21 U-48PR1H8 Máy điều hòa không khí Trước khi bật thiết bị, vui lòng đọc kỹ hướng dẫn sử dụng này và...
  • Page 2: Mục Lục Hướng Dẫn Nhanh

    Sử dụng điều khiển trong khoảng 8m tính từ bộ phận nhận tín hiệu điều khiển từ xa trên dàn lạnh. Hướng dẫn nhanh Lắp pin Điều chỉnh đồng hồ Nhấn , sau đó nhấn để cài đặt thời gian. •...
  • Page 3: Table Of Contents

    Cảm ơn bạn đã lựa chọn Máy điều hòa không khí Panasonic. Mục Lục Hướng dẫn nhanh .....2-3 Hướng dẫn sử dụng an toàn .........4-11 Cách sử dụng ....12-13 Tìm hiểu thêm....14 Vệ sinh máy điều hòa ..15-16 Những vấn đề thường gặp ........17-20...
  • Page 4: Hướng Dẫn Sử Dụng An Toàn

    Hướng dẫn sử dụng an toàn Để tránh gây thương tích cho bản thân, người khác hoặc tổn thất về tài sản, hãy làm theo những chỉ dẫn dưới đây: BÁO ĐỘNG Vận hành sai hướng dẫn sử dụng có thể gây ra hư hại với các mức độ...
  • Page 5 Nguồn cấp điện CẢNH BÁO Không sử dụng các dây đã bị sửa đổi, các dây nối, hoặc các dây không theo chỉ định Khối trong nhà và khối ngoài trời để tránh bị quá tải và cháy nổ. Không vệ sinh máy bằng nước, benzen, chất ăn Để...
  • Page 6 Hướng dẫn sử dụng an toàn Phải đảm bảo rằng các chất ngoại lai (dầu, BÁO ĐỘNG nước, vân vân) không chui vào ống. Tương tự, khi bảo quản đường ống, cần bọc kín đầu hở bằng kẹp, dây buộc (bảo quản R32 giống như bảo quản R410A).
  • Page 7 f) Cần có các bước phòng ngừa để tránh 2. Bảo trì những rung lắc quá mạnh có thể ảnh 2-1. Nhân viên bảo trì hưởng tới đường ống làm lạnh. • Hệ thống được kiểm tra, thường xuyên giám g) Cần đảm bảo các thiết bị...
  • Page 8 Hướng dẫn sử dụng an toàn 2-3. Kiểm tra chất làm lạnh 2-7. Kiểm tra thiết bị làm lạnh • Toàn bộ khu vực làm việc phải được kiểm tra • Khi phải thay đổi các thiết bị điện, phải sử với thiết bị...
  • Page 9 3. Sửa chữa các bộ phận đã được bịt kín 6. Phát hiện môi chất lạnh dễ bắt cháy • Trong suốt quá trình sửa chữa các bộ phận • Trong bất kỳ trường hợp, không được sử đã được bịt kín, phải ngắt không cho các bộ dụng các nguồn bắt lửa tiềm ẩn trong quá...
  • Page 10 Hướng dẫn sử dụng an toàn 8. Di chuyển và tiêu hủy 9. Quy trình nạp nhiên liệu • Khi can thiệp vào hệ thống làm lạnh để tiến • Ngoài các bước nạp nhiên liệu thông thường, hành sửa chữa – hoặc để thực hiện bất phải tuân thủ...
  • Page 11 e) Nếu không thể dùng máy hút chân không, • Thiết bị thu hồi phải đang trong điều kiện hoạt cần lặp đi lặp lại các hoạt động trên để động tốt với các chỉ dẫn liên quan tới thiết bị có...
  • Page 12: Cách Sử Dụng

    Cách sử dụng Cánh đảo gió ngang Mắt nhận Các đèn hiển thị AUTO POWER TIMER nanoeX Lưới lọc khí Khe lấy gió vào Để điều chỉnh tốc độ quạt • Dùng điều khiển từ xa để điều chỉnh tốc độ quạt theo ý...
  • Page 13 Để tận hưởng môi trường tươi mới hơn và sạch hơn • bắt đầu tự động khi thiết bị được bật. • Nhấn để OFF (TẮT) thao tác này theo cách thủ công. • Chế độ này có thể được kích hoạt ngay cả khi máy đang OFF (TẮT). Chú ý rằng tốc độ của cánh đảo gió...
  • Page 14: Tìm Hiểu Thêm

    Tìm hiểu thêm... Chế độ hoạt động FAN (QUẠT GIÓ) : Để kích hoạt chế độ lưu. COOL (LÀM LẠNH) : Đem lại sự làm mát dễ chịu một cách hiệu quả và phù hợp với nhu cầu của bạn. DRY (HÚT ẨM) : Khi nhiệt độ...
  • Page 15: Vệ Sinh Máy Điều Hòa

    Vệ sinh máy điều hòa Cần tiến hành vệ sinh và bảo dưỡng định kỳ để đảm bảo máy hoạt động tối ưu. Máy bẩn sẽ gây ra hỏng hóc. Liên hệ trạm bảo hành ủy quyền để được trợ giúp. •...
  • Page 16 Vệ sinh máy điều hòa Bảo trì lưới lọc khí • Nên làm vệ sinh lưới lọc sau mỗi 6 tuần. • Sau khi lưới lọc được làm sạch, nhấn để khởi động. Tùy chọn (Đối với tất cả các khối trong nhà) Vui lòng tham khảo ý...
  • Page 17: Những Vấn Đề Thường Gặp

    Những vấn đề thường gặp Những hiện tượng sau không phải sự cố thuộc thiết bị. Hiện tượng Nguyên nhân Hệ thống không bật hoặc phản hồi với bộ điều • Đối với sản phẩm mới lần đầu bật nguồn sau khi lắp đặt, khiển từ...
  • Page 18 Những vấn đề thường gặp Lấy mã lỗi Nếu máy ngừng hoạt động và đèn báo TIMER (HẸN GIỜ) nhấp nháy, dùng điều khiển từ xa để lấy mã báo lỗi. Nhấn trong 5 giây Nhấn nút hoặc cho đến khi mã đến khi bạn nghe thấy tiếng được hiển thị...
  • Page 19 Hiển thị chẩn đoán Vấn đề/Kiểm soát bảo vệ Bộ điều khiển từ xa bị lỗi khi nhận tín hiệu từ khối trong nhà Bộ điều khiển từ xa bị lỗi khi truyền tín hiệu đến khối trong nhà Khối trong nhà bị lỗi khi nhận tín hiệu từ bộ điều khiển từ xa Khối trong nhà...
  • Page 20 Những vấn đề thường gặp Khi... ■Điều khiển bị mất hoặc không hoạt động AUTO POWER TIMER nanoeX 1.Nhấn nút AUTO OFF/ON (TỰ ĐỘNG TẮT/BẬT) một lần để sử dụng ở chế độ COOL (LÀM LẠNH). 2.Nhấn nút AUTO OFF/ON (TỰ ĐỘNG TẮT/BẬT) lần nữa để tắt máy. ■...
  • Page 21: Thông Tin Cần Lưu Ý

    Thông tin cần lưu ý Thông tin cho người sử dụng về việc thu gom và hủy máy cũ và pin đã qua sử dụng [Thông tin về việc hủy máy ở các nước ngoài Liên minh châu Âu.] Những ký hiệu này chỉ có giá trị trong Liên minh châu Âu. Nếu bạn muốn hủy những sản phẩm này, vui lòng liên hệ...
  • Page 22: Quick Guide

    Use the remote control within 8 m from the remote control receiver on the indoor unit. Quick Guide Inserting the batteries Clock setting Press , then press set the time. • Press approximately 5 seconds to Pull out the back cover of show the time as 12-hour remote control.
  • Page 23 Thank you for purchasing Panasonic Air Conditioner. Table of Contents Quick Guide ....22-23 Safety Precautions ..24-31 How to Use ....32-33 To Learn More....34 Cleaning the Air Conditioner ....35-36 Troubleshooting ....37-40 Information ......41 Accessories Included: • Remote control • AAA or R03 batteries × 2 •...
  • Page 24: Safety Precautions

    Safety Precautions To prevent personal injury, injury to others or property damage, please comply with the following: WARNING Incorrect operation due to failure to follow instructions below may cause harm or damage, the seriousness of which is classifi ed as below: Indoor unit and outdoor unit This appliances is not intended for accessibility by the general public.
  • Page 25 Power supply CAUTION Do not use a modifi ed cord, joint cord, extension cord or unspecifi ed cord to prevent Indoor unit and outdoor unit overheating and fi re. Do not wash the indoor unit with water, To prevent overheating, fi re or electric shock: benzine, thinner or scouring powder to avoid •...
  • Page 26 Safety Precautions Must always ensure that foreign matter (oil, WARNING water, etc.) does not enter the piping. Also, when storing the piping, securely seal the opening by pinching, taping, etc. (Handling of R32 is similar to R410A.) This appliance is fi lled with R32 •...
  • Page 27 f) Precautions shall be taken to avoid 2. Servicing excessive vibration or pulsation to 2-1. Service personnel refrigerating piping. • The system is inspected, regularly supervised g) Ensure protection devices, refrigerating and maintained by a trained and certifi ed piping and fittings are well protected service personnel who is employed by the against adverse environmental effects person user or party responsible.
  • Page 28 Safety Precautions 2-3. Checking for presence of refrigerant 2-7. Checks to the refrigerating equipment • The area shall be checked with an • Where electrical components are being appropriate refrigerant detector prior to and changed, they shall be fi t for the purpose and during work, to ensure the technician is aware to the correct specifi...
  • Page 29 3. Repairs to sealed components 6. Detection of fl ammable refrigerants • During repairs to sealed components, all • Under no circumstances shall potential electrical supplies shall be disconnected from sources of ignition be used in the searching or the equipment being worked upon prior to any detection of refrigerant leaks.
  • Page 30 Safety Precautions 8. Removal and evacuation 9. Charging procedures • When breaking into the refrigerant circuit • In addition to conventional charging to make repairs – or for any other purpose procedures, the following requirements shall – conventional procedures shall be used. be followed.
  • Page 31 e) If a vacuum is not possible, make a manifold • The recovery equipment shall be in good so that refrigerant can be removed from working order with a set of instructions various parts of the system. concerning the equipment that is at hand and f) Make sure that cylinder is situated on the shall be suitable for the recovery of fl...
  • Page 32: How To Use

    How to Use Horizontal fl ap Remote control receiver Indicators AUTO POWER TIMER nanoeX Intake grille Air fi lter To adjust fan speed • The fan speed can be adjusted as desired by using remote control. To adjust airfl ow direction OFF/ON MODE nanoeX...
  • Page 33 To enjoy fresher and cleaner environment • automatically starts when the unit is turned on. • Press to turn OFF this operation manually. • This operation can be activated even when the unit is OFF. Note that the fl ap and fan speed will operate according to the remote control setting.
  • Page 34: To Learn More

    To Learn More... Operation mode : To enables air circulation in the room. COOL : Provides effi cient comfort cooling to suit your needs. : When the room temperature is more likely to reach the level that was set, the fan speed is set to ‘‘breeze’’...
  • Page 35: Cleaning The Air Conditioner

    Cleaning the Air Conditioner Cleaning has to be carried out at regular intervals to ensure the unit is at optimal performance. A dirty unit may cause malfunction. Consult an authorised dealer. • Before cleaning, switch off the power supply and unplug the unit. •...
  • Page 36 Cleaning the Air Conditioner Air fi lter maintenance • lt is recommended to clean the air fi lter every 6 weeks. • After the air filter is cleaned, press to reset. Optional (For all indoor units) Consult your dealer or service center when the (Filter) appears on the display of the wired remote controller.
  • Page 37: Troubleshooting

    Troubleshooting The following symptoms do not indicate malfunction. Symptom Cause The system is not turn on or respond to remote • For new product fi rst time power on after installation, the controller immediately after power on. system requires approximately 5 minutes for “System Auto confi...
  • Page 38 Troubleshooting How to retrieve error codes If the unit stops and the TIMER indicator blinks, use the remote control to retrieve the error code. Press for 5 seconds Press button until until a code is you hear beep sound, then displayed write down the error code TIMER...
  • Page 39 Diagnostic display Abnormality/Protection control Remote Controller Error In Receiving Signal from Indoor Unit Remote Controller Error In Transmitting Signal To Indoor Unit Indoor Unit Error In Receiving Signal from Remote Controller Indoor unit not receiving signal from the outdoor unit Duplication of Indoor Unit Address Setting Duplication of Main Remote Controller Setting Duplication of Main Unit in Group Control...
  • Page 40 Troubleshooting When... ■The remote control is missing or a malfunction has occurred AUTO POWER TIMER nanoeX 1.Press AUTO OFF/ON once to use in COOL mode. 2.Press AUTO OFF/ON again to turn off the unit. ■ Conducting a seasonal inspection after extended period of non-use •...
  • Page 41: Information

    Information Information for Users on Collection and Disposal of Old Equipment and used Batteries [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
  • Page 42 Memo ACXF55-32051_SS1021-1.indb 42 ACXF55-32051_SS1021-1.indb 42 13/10/2021 6:32:29 PM 13/10/2021 6:32:29 PM...
  • Page 43 Memo ACXF55-32051_SS1021-1.indb 43 ACXF55-32051_SS1021-1.indb 43 13/10/2021 6:32:29 PM 13/10/2021 6:32:29 PM...
  • Page 44 Panasonic Corporation Website: http://www.panasonic.com © Panasonic Corporation 2021 ACXF55-32051 Printed in China SS1021-1 ACXF55-32051_SS1021-1.indb 44 ACXF55-32051_SS1021-1.indb 44 13/10/2021 6:32:29 PM 13/10/2021 6:32:29 PM...

Table of Contents