NEC MultiSync FE791SB User Manual page 4

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG
WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE
COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Contents
Sales Office List
Captive
Signal Cable User's manual
Quick Start
Power Outlet
Power
Cord
Figure A
Figure B
Controls
OSM (On-Screen Manager) control buttons on the front
of the monitor function as follows:
Main Menu
EXIT Exits the OSM menu.
CONTROL Moves the highlighted
Y
area left/right to select
/
one of the sub-menus.
CONTROL Has no function.
–/+
SELECT/ Enters sub-menu.
SBMODE
RESET Resets all the controls
within the highlighted
menu to the factory
setting.
NOTE: When RESET is pressed in the main and sub-menu, a warning
window will appear allowing you to cancel the reset function.
NOTE: When the OSM is off, it will act as the SuperBright (SB) function
key. User can select between SB MODE OFF, SB MODE1, and
SB MODE2. The first time this key is pressed, the current SB
Mode is indicated. Within a 3 second window, if this key is
selected again, the SB MODE will change to the next SB MODE.
4
WARNING
Power Cord
CD ROM
15-pin mini D-SUB
Power Button
Sub-Menu
Exits to the OSM con-
trols main menu.
Moves the highlighted
area left/right to select
one of the controls.
Moves the bar in the - or
+ direction to decrease
or increase the adjust-
ment.
Has no function.
Resets the highlighted
control to the factory
setting.
RISK OF ELECTRIK SHOCK • DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have
sufficient magnitude to cause electric shock. Therefore, it is dangerous to
make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation
and maintenance of this unit has been included. Therefore, it should be read
carefully in order to avoid any problems.
MultiSync FE monitor box* should contain the following:
• • • • • MultiSync FE Monitor with tilt/swivel base
• • • • • Power cord
• • • • • Captive Signal Cable
• • • • • User 's manual
• • • • • Sales Office List
• • • • • CD ROM (includes complete User's Manual in PDF format)
* Remember to save your original box and packing material to
transport or ship the monitor.
To attach the MultiSync FE monitor to your system, follow
these instructions:
1. Turn off the power to your computer and MultiSync FE monitor.
2. If necessary, install the display card. For more information,
refer to the display card manual.
3. For PC: Connect the 15-pin mini D-SUB of the captive signal
cable to the connector for the display card in your system (Figure A).
Tighten all screws.
4. Connect one end of the power cord to the MultiSync FE monitor
and the other end to the power outlet (Figure A).
5. Turn on the monitor (Figure B) and the computer.
6. This completes the installation.
NOTE: If you need more information, please refer to complete
User's Manual in CD ROM.
For example, the current mode is SB MODE OFF, the key is
pressed twice within a 3 second time frame, the SB MODE will
change to SB MODE1 and so on. The color temperature at each
SB Mode is adjusted by appropriate color control except for the
sRGB mode whose color setting cannot be adjusted. When the
unit is turned off, it will reset to SB off mode.
Super Bright Mode OFF: for text based images (normal use)
Super Bright Mode-1 ON: for images
Super bright Mode-2 ON: for moving image such as DVD
movies
Brightness/Contrast Controls
Brightness: Adjusts the overall image and background screen
brightness.
Contrast: Adjusts the image brightness in relation to the
background.
Degauss: Eliminates the buildup of stray magnetic fields which
alter the correct scan of the electron beams and affect the purity
of the screen colours, focus and convergence. When activated,
your screen image will jump and waver a bit as the screen is
demagnetized.
Caution: Please allow a minimum of 20 minutes to elapse
between uses of the Degauss Control.
CAUTION