Dimplex Optimyst 3STEP-RGB-EU Operating Instructions Manual page 10

THERMAL SAFETY CUT-OUT
A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if
the heat outlet was restricted in any way. If the cut-out operates, unplug the heater from the socket outlet and allow
approximately 10 minutes before reconnecting. Before switching the heater back on remove any obstruction that may
be restricting the heat outlet, then continue normal operation.
ADVANCE MENU OPTIONS
The Eco handset is equiped with advanced menu options to further enhance the product functionality. To access:
Press the Menu to go to the home screen.
Press and Hold the Menu and Advance button at same time for 3 seconds to access the Advance menu options.
to go to desired menu & press ENTER to select.
Use the or
RUNBACK TIMER
The product will go to standby after designated period.
(will be 昀氀ashing) and Enter to go to time menu.
Select ON using or
Press or to highlight desired preset time period (30min, 1hr, 1.5hr, 2hr, 4hr, 8hr) and ENTER to select.
Will highlight on screen when active.
SET BACK POINT
The maximum temperature set point on the product is 30°C You have the option to reduce this set point.
ADAPTIVE START
The built-in electronics in this appliance have a learning function with regards to how long it takes to heat up a room.
Having learnt how quickly it can heat up your room, the appliance is able to turn on at just the right time in order to get
the room up to a comfortable temperature when you want it. For example, if you get up at 7am, you would normally have
to guess when to turn the heating on in order for it to pre-heat the room in time. Depending on how cold it is outside, this
could mean the room is still cold when you have to get out of bed, or mean that its been warm for half an hour before
it needed to be. Adaptive Start means that if you select 21°C at 7am, the heater will turn on exactly when it needs to in
order to meet this target, running for shorter periods of time when the weather is mild, and ensuring the room is nice and
warm in the winter. The Adaptive Start function will automatically activate when you use the Timer Mode.
FROST PROTECT
Frost protect mode prevents the room from freezing. The heater will turn on if the room temperature drops below 7ºC.
Will indicate on the screen when active.
TEMPERATURE UNITS DISPLAY
to select and ENTER to con昀椀rm.
User can change the Units of the temperature (ºC and ºF). Use or
FLAME CONNECT APP
The 昀椀replace is capable of being controlled using the Flame Connect App for mobile devices. This is available to down-
load to your device from Google Play or Apple App stores. Follow the on screen instructions for set-up.
NOTE: The 昀椀replace will not operate using the provided remote control when the app is open on a mobile device.
LOW WATER / REFILLING THE WATER TANKS
When the water tanks have emptied and the water level in the product is getting low, the product will 昀氀ash its LEDs twice
and beep twice. The product will operate for a further 15 minutes before beeping once and switching into low water
mode. For products being operated with the LED log fuel bed, only the fuel bed will remain illuminated while in low water
mode. At this point, the product can either be switched into stand-by mode using the remote control or Bluetooth receiver
or the product can be re昀椀lled with water. Re昀椀lling the product with water will cause the product to restart automatically.
To re昀椀ll the tank, open the drawer and remove the water tank from its position on top of the sump. Re昀椀ll the water tank
using 昀椀ltered/decalci昀椀ed water only. The tank can then be replaced on top of the sump. If the product was not switched
into stand-by mode after experiencing low later, the product will restart automatically after about 20 seconds of re昀椀lling.
10