Overheating Protection; Cleaning And Maintenance; Technical Data - camry CR 7721 User Manual

Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 6
5. TEMP – set temperature button
7. Up button
9. Maximum heating power indicator
11. Heating activation indicator
13. Timer indicator (time remaining until automatic shutdown)
TThe remote control (V.) operation way is same as buttons on control panel (II).
USAGE
1. Insert the mains plug into a wall socket corresponding to the technical data.
2. Push the power switch (IV.) on the right side of device, the control panel (II.) will light up, showing a readout of the room temperature
indicate (12) in Centigrade (°C) and timer indicator (13). The timer indicator (13) will be set to zero.
3. When you press the power button (3), the minimum heating settings (10) will appear on the readout. The default setting is 35°C, so if the
room temperature drops below the value, the heating system start up.
4. Press the TEMP button (5) once and readout indicating the heating temperature will flash. At his point, use the button (7) and (8) to set
the heating temperature to your preference in range 15-35°C. Keep fixed temperature unchanged for 5 seconds and the device will
remeber your preference, then it will show present room temperature (12).
5. Press the PROG button (4) once to switch between maximum heating level (9) and minimum heating level (10).
6. To set the time (in hours) after which the device turns off automatically, follow the steps below. Press the time button (6) once and the
readout indication the time until the device powers off will flash. At this point, use the button (7) or (8)to set the timer to your preference in
time range 0-24 hours. Keep fixed number of hours unchanged for 5 seconds and the device will record your preference and return the
readout to show the remaining time (13) in hours until the device powers off. If you set the time to zero, the device will not power off
automatically.
7. Press the power button (3) again and switch off the power switch (IV.) to switch off the device.

OVERHEATING PROTECTION

This device is equipped with overheating protection for your safety.
If the temperature inside the device becomes too high, it switches off automatically.
1. Check whether the air inlet or air outlet are clogged. If there are, clean any obstruction.
2. Wait for the device to cool down.
3. Then you can continue to use it normally.
4. If the cause cannot be found and the problem occurs repeatedly, pass the device to authorized service center for repair.

CLEANING AND MAINTENANCE

1. Always unplug the device from the power socket before cleaning.
2. If during cleaning items such as the power plug, thermostat, electrical contacts etc. are soaked before being used again, they should be
thoroughly dried.
3. Do not use aggressive detergents in the form of emulsions, lotions, pastes, etc. to clean the cabinet. They can, among other things,
remove the information graphic symbols, such as warning signs, etc.
4. Ensure that the device has cooled down before cleaning.
5. When the device is not used for long periods of time, it should be protected against dust and stored in a clean dry place.

TECHNICAL DATA:

Voltage: 220-240V ~50/60Hz
Power: 1500W
IPX 0
DO NOT COVER« INSCRIPTION IMPORTANCE
The inscription on the device means that the device is not to be covered with clothing, blankets and other textile
products which could cause ignition.
WARNING: Do not use this equipment near bathtubs, showers, swimming pools and similar
water tanks.
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins.
Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the
environment. Do not dispose this appliance in the common waste bin.
6. TIME – timer button
8. Down button
10. Minimum heating power indicator
12. Room temperature indicator
"Caution Hot Surface" - The temperature of available surfaces may be higher
when the equipment is working, which means that the housing elements become
very hot during operation during operation, SAVE CAREFUL !!!
8

Advertisement

Table of Contents
loading

Table of Contents