Advertisement
10
TOP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
FLOAT
CUP
FILL
VALVE
WATER LEVEL
ADJUSTMENT
CLIP
VALVE
BODY
LOCK NUT
CONE WASHER
COUPLING NUT
(HAND TIGHT ONLY)
12
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
WARNING:
!
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
Repair parts are determined by toilet tank number which can be found marked inside tank.
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
PART NO.
047242-XXX0A
047192-XXX0A
730288-XXX0A
738517-XXX0A
738171-XXX0A
034783-XXX0A
738565-400.0070A
738565-401.0070A
738565-402.0070A
738565-404.0070A
738138-0070A
738484-0070A
738360-0070A
738361-0070A
738757-0070A
738159-0070A
738397-0070A
738358-0070A
738359-0070A
738565-418.0070A
730519-0070A
ARM
REFILL
NIPPLE
TUBE
TANK
LEVER
Fig. 10A
"S"
CLIP
FLUSH
VALVE
LINK
ADJUSTABLE
HEIGHT
FLAPPER
SHANK
WASHER
THREADED
SHANK
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
Diagram 1
REPAIR PARTS LIST
DESCRIPTION
TRIP LEVER
TRIP LEVER
TRIP LEVER
TRIP LEVER
RIGHT HAND TRIP LEVER
BOLT CAP KIT (INCL TWO COVERS & WASHERS)
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUSH VALVE
FLUSH VALVE
FLUSH VALVE
FLUSH VALVE
COUPLING KIT, KIT 242
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLUIDMASTER 400A VALVE
COUPLING KIT, BOWL-TO-TANK KIT 233
ADJUSTMENTS
a.
Adjust water level. Water level
should be adjusted to level
indicated on tank by adjusting float
cup.
See Step 11 for water level
adjustment method
b.
If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 10A)
and take up slack on the chain, and
reinsert on lift rod. Make sure the
chain is not too taught.
- 3 -
11
Turn on water supply.
Adjust water to desired
level by squeezing water
level adjustment clip and
moving FLOAT CUP up or
down along stainless steel
link.
TANK NUMBER
✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔
✔ ✔
✔
✔
✔
✔
✔
730504-1 0 0 REV. E
✔
✔
✔
✔
✔
Advertisement
