Table of Contents
Advertisement
Quick Links
ARXP018GLAH
Refer to the rating label for the serial number,
manufactured year and month.
TM
INSTALLATION MANUAL
INSTALLATIONSANLEITUNG
MANUEL D'INSTALLATION
MANUAL DE INSTALACIÓN
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
A uso esclusivo del personale tecnico autorizzato.
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
ΕΣΩΤΕΡΙΚΗ ΜΟΝΑΔΑ (Τύπος αγωγού)
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
UNIDADE INTERIOR (Tipo de tubagem)
РУКОВОДСТВО ПО УСТАНОВКЕ
Только для авторизованного обслуживающего персонала.
INDOOR UNIT (Duct type)
For authorized service personnel only.
INNENGERÄT (Kanaltyp)
Nur für autorisiertes Fachpersonal.
UNITÉ INTÉRIEURE (type conduit)
Pour le personnel agréé uniquement.
UNIDAD INTERIOR (Tipo conducto)
UNITÀ INTERNA (tipo a condotto)
Apenas para técnicos autorizados.
ВНУТРЕННИЙ МОДУЛЬ (Короб)
MONTAJ KILAVUZU
İÇ ÜNİTE (Kanal tipi)
Yalnızca yetkili servis personeli için.
[Original instructions]
PART No. 9373385271
MADE IN P.R.C.
Advertisement
Table of Contents
Related Manuals for Fujitsu Airstage ARXP018GLAH
Summary of Contents for Fujitsu Airstage ARXP018GLAH
- Page 1 INSTALLATION MANUAL INDOOR UNIT (Duct type) For authorized service personnel only. INSTALLATIONSANLEITUNG INNENGERÄT (Kanaltyp) Nur für autorisiertes Fachpersonal. MANUEL D’INSTALLATION UNITÉ INTÉRIEURE (type conduit) Pour le personnel agréé uniquement. MANUAL DE INSTALACIÓN UNIDAD INTERIOR (Tipo conducto) ARXP018GLAH Únicamente para personal de servicio autorizado. MANUALE DI INSTALLAZIONE UNITÀ...
-
Page 2: Table Of Contents
INSTALLATION MANUAL This mark indicates procedures which, if improperly performed, CAUTION might possibly result in personal harm to the user, or damage to PART No. 9373385271 property. VRF system indoor unit (Duct type) Read carefully all security information before use or install the air conditioner. Contents Do not attempt to install the air conditioner or a part of the air conditioner by yourself. -
Page 3: Accessories
2.3. Accessories 2.4. Optional parts When connecting the square duct and round duct, use the optional square flange or WARNING round fl ange. Square fl ange For installation purposes, be sure to use the parts supplied by the manufacturer or other prescribed parts. -
Page 4: Installation Work
[Top view] (unit : mm) 3. INSTALLATION WORK 500 or more Correct initial installation location is important because it is diffi cult to move unit after it is installed. Indoor unit 3.1. Selecting an installation location Service access WARNING Select installation locations that can properly support the weight of the indoor. Install the units securely so that they do not topple or fall. - Page 5 WARNING CAUTION When fastening the hangers, make the bolt positions uniform. When air is taken in from the bottom side, the operating sound of the product will easily eater the room. The distance of is adjustable according to the place of the hanging bolts. Install the product and intake grilles where the affect of the operating sound is small.
-
Page 6: Pipe Installation
CAUTION 4. PIPE INSTALLATION To prevent people from touching the parts inside the unit, be sure to install grilles on the inlet and outlet ports. The grilles must be designed in such a way that cannot be removed without tools. CAUTION If an intake duct is installed, take care not to damage the temperature sensor (the Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with... -
Page 7: Installing Heat Insulation
4.3.1. Flaring Tighten with 2 wrenches. • Use special fl are tool exclusive for R410A. Holding wrench (1) Cut the connection pipe to the necessary length with a pipe cutter. (2) Hold the pipe downward so that cuttings will not enter the pipe and remove any Flare nut burrs. - Page 8 (Right side) Applying 240 mm area of adhesive Joint pipe Hard PVC side (locally purchased) Drain pipe (VP25) (locally purchased) 4 mm or less Wrap the Drain hose insulation around the drain hose connection. Liquid pipe Drain hose insulation Gas pipe (Accessories) Drain port Drain pan...
-
Page 9: Electrical Wiring
6. ELECTRICAL WIRING 6.1. Electrical requirement Voltage rating 220-240 V ~ 50 Hz WARNING 230 V ~ 60 Hz Electrical work must be performed in accordance with this Manual by a person certifi ed Operating range 198 to 264 V (50 Hz) under the national or regional regulations. -
Page 10: Wiring Method
WARNING 6.2. Wiring method When using solid core cables, do not use the ring terminal. If you use the solid core cables with the ring terminal, the ring terminal's pressure bonding may malfunction and Example cause the cables to abnormally heat up. Outdoor unit or RB unit *1 B. -
Page 11: Connection Of Wiring
Tightening torque M3 screw (Transmission /X1, X2) 0.5 to 0.6 N·m (Remote controller /Y1, Y2, Y3) (5 to 6 kgf·cm) CAUTION To peel the fi lm from the lead cable, use a dedicated tool that will not damage the conductor cable. When installing a screw on the terminal block, do not cut the cable by overtightening the screw. -
Page 12: External Input And External Output (Optional Parts)
6.5. External input and external output (Optional parts) DC power supply P.C.B 12 to 24V Load Controller PCB resistance CNA01 Output terminal (CNB01) Apply voltage terminal P.C.B (CNA03) Load (CNA01) resistance CNA01 Dry contact terminal (CNA02) P.C.B connected unit (CNA04) CNA01 ●... - Page 13 [In the case of “Pulse” input] ● When connecting with unit equipped with a power supply Connector Input signal Command P.C.B OFF → ON Operation Connected CNA01 or CNA02 device 1 OFF → ON Stop Connected device 2 * The last command has priority. Connected * The indoor units within the same remote controller group operates in the same mode.
-
Page 14: Remote Sensor (Optional Parts)
6.6. Remote sensor (Optional parts) 6.7. IR receiver unit (Optional parts) • For the installation method, please refer to the INSTALLATION MANUAL of remote • For the installation method, please refer to the INSTALLATION MANUAL of IR receiver sensor. unit. Connection methods Connection methods •... -
Page 15: Drain Pump Unit (Optional Parts)
6.8. Drain pump unit (Optional parts) 7.1. Setting the address Manual address setting method • For the installation method, please refer to the INSTALLATION MANUAL of drain pump • If the receiver unit is attached, the indoor unit address and the refrigerant circuit unit. -
Page 16: Custom Code Setting
(3) Remote controller address 7.3. Static pressure mode i) 3-wire type Rotary switch (RC AD SW)...Factory setting “0” When connecting multiple indoor units to 1 standard wired remote controller, set the CAUTION address at RC AD SW in sequence from 0. If the applicable static pressure does not match the static pressure mode, the static Setting Setting range... -
Page 17: Function Setting
7.4. Function setting 8. TEST RUN • FUNCTION SETTING can be performed with the wired or wireless remote controller. 8.1. Test run using Outdoor unit (PCB) (The remote controller is optional equipment) • Refer to the wired or wireless remote controller manual for detailed setting information. •... -
Page 18: Error Codes
Wired remote controller display 10. ERROR CODES UTY-RNK* / UTY-RNKYT (3-wire type) If you use a wired type remote controller, error codes will appear on the remote control- Error code ler display. If you use a wireless remote controller, the lamp on the photodetector unit will output error codes by way of blinking patterns.