Nedis ACMB1WT12 - Local Air Conditioner Manual

Also See for ACMB1WT12:

Quick start manual (36 pages)

Table of Contents

Contents

1 Description
2 Installation
3 Protection functions
4 Technical data
5 Safety
- 5.1 Electrical safety
6 Cleaning and maintenance
7 Documents / Resources
- 7.1 Download manual

Nedis ACMB1WT12 - Local Air Conditioner Manual

Description

Device overview
Device (fig. A)

Control panel
Air outlet
On/off button	Press the button to switch on or off the device.
Mode button	Repeatedly press the button to select the mode: Cooling mode / Dehumidifying mode / Fan mode.
Up button Down button	Cooling mode: Press the up button or the down button to change the set temperature. Simultaneously press both buttons to switch between Celsius (°C) and Fahrenheit (°F). Press the up button or the down button to change the set timing value.
Timer button	Press the button to set the timer. Note: The timer can be set upto a maximum of 24 h.
Wind Speed selection button	In cooling or fan mode, press the button repeatedly to select the fan speed: Low / Medium / High. In dehumidification mode the wind speed selection button is invalid. The fan remains in low wind speed operation.
Display window	The display window shows the set temperature or the set timing.
Cooling mode indicator	This indicator shows that the device is in cooling mode.
Dry mode indicator	This indicator shows that the device is in dehumidifying mode.
Fan indicator	This indicator shows that the device is in fan mode.
Water reservoir indicator	This indicator shows that the water reservoir needs drainage.
Celsius indicator	This indicator shows that the temperature is set in Celsius (°C).
Fahrenheit indicator	This indicator shows that the temperature is set in Fahrenheit (°F).
Hr indicator	This indicator shows that the device is in timer mode.
Sleep mode indicator	This indicator shows that the device is in sleeping mode. This function is only available in cooling mode. Simultaneously press buttons 5 and 8 to activate.
On/off indicator	This indicator shows that the device is on or off.
Handle
Continous drainage hole	In the cooling and dehumidification mode continuous draining is possible: Unplug the water plug and connect the water outlet to a water container or drainage.
Power cord fixing board
Remote control holder
Drainage hole	To drain the device, switch off the device and disconnect the power plug of the mains socket. Loosen the drainage cover and unplug the water plug. Let the water flow into a water container. Connect the water plug and tighten the drainage cover.
Air filter	For an optimum filtration clean the filter frame and inner filter regularly.
Exhaust connector
Air filter	For an optimum filtration clean the filter frame and inner filter regularly.
Wheels	Place the device on a flat and dry surface.
Power cord
Exhaust pipe	Connect the exhaust pipe to the exhaust connector and the connector of the window adapter. The length of the exhaust hose must be between 28 and150 cm. Do not use extension tubes. Make sure that the exhaust is unobstructed.
Connector of the window adapter	The device can be placed in horizontal or vertical direction.

Remote control overview
Remote control (fig. B)

Remote control	Use the remote control to control the device from a distance of maximum 5 m.
On/off button	Press the button to switch on or off the device.
Timer button	Press the button to set the timing value.
Swing button	Press the swing button to open or close swing style. The air flow of the air outlet can blow at different angles.
Sleep mode	In cooling mode, press the button to select sleep mode. Note: After selecting the sleep mode the temperature increases by 1°C after one hour and again 1°C after two hours. After two hours the temperature remains constant.
Up button Down button	Press the up button to increase the temperature or the timing set value. Note: The temperature can be set to a minimum of 16°C and a maximum of 31°C. Press the down button to decrease the temperature or the timing set value.
Mode selection button	Repeatedly press the button to select the mode: Cooling mode / Dehumidifying mode / Fan mode.
Fan button	Press the fan button to select high, medium or low wind speed output.
Celsius - Fahrenheit button	Press the button to switch between Celsius (°C) and Fahrenheit (°F).

Installation

Refer to the illustration to install the device.

(fig. C)

Note: The distance between the device and the wall or other objects must be at least 50 cm.

Protection functions

The device has five protection functions: Frost protection function, overfow protection, automatic defrosting, automatic thermal protection and protection of the compressor.

Technical data

Electrical power	1357 W
Cooling capacity	12,000 BTU / 3.5 kW
Energy efficiency ratio (EER)	2.60
Coefficient of performance (COP)	2.50
Energy class	A
Air circulation	400 m³/h
Noise level	≤ 65 dB
Room size capacity	18 - 26 m²
Dehumidification	28 l/day
Refrigerant	R290, 230 g
Dimensions	42 x 72 x 36 cm
Weight	28 kg

Safety

Read the manual carefully before use. Keep the manual for future reference.
Only use the device for its intended purposes. Do not use the device for other purposes than described in the manual.
The manufacturer is not liable for consequential damages or for damages to property or persons caused by nonobservance of the safety instructions and improper use of the device.
The device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the device in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised. Keep the device and the mains cable out of the reach of children younger than 8 years. Children shall not play with the device.
Do not use the device if any part is damaged or defective. If the device is damaged or defective, replace the device immediately.
Do not use the device outdoors. The device is suitable for indoor use only.
The device is suitable for domestic use only. Do not use the device for commercial purposes.
Do not use the device near bathtubs, showers, basins or other vessels containing water.
Do not immerse the device in water or other liquids. If the device is immersed in water or other liquids, do not remove the device with your hands. Immediately remove the mains plug from the wall socket. If the device is immersed in water or other liquids, do not use the device again.
Keep the device away from heat sources. Do not place the device on hot surfaces or near open flames.
Do not use the device near explosive or flammable materials.
Keep your hands away from the moving parts. Do not insert fingers, pencils or other objects through the guard.
Before moving the device, always remove the mains plug from the wall socket. Do not pull the mains cord.

Electrical safety

RISK OF ELECTRIC SHOCK
DO NOT OPEN

To reduce risk of electric shock, this product should only be opened by an authorized technician when service is required.
Disconnect the product from the mains and other equipment if a problem should occur.
Do not use the device if the mains cable or mains plug is damaged or defective. If the mains cable or mains plug is damaged or defective, it must be replaced by the manufacturer or an authorised repair agent.
Before use, always check that the mains voltage is the same as the voltage on the rating plate of the device.
Connect the device to an earthed wall socket. If necessary, use an earthed extension cable of a suitable diameter.
Always fully unwind the mains cable and the extension cable.
The device is not intended to be operated by means of an external timer or separate remote-control system.
Do not move the device by pulling the mains cable. Make sure that the mains cable cannot become entangled. Make sure that the mains cable does not hang over the edge of a worktop and cannot be caught accidentally or tripped over.
Do not immerse the device, the mains cable or the mains plug in water or other liquids.
Do not leave the device unattended while the mains plug is connected to the mains supply.

Cleaning and maintenance

Before cleaning or maintenance, switch off the device, remove the mains plug from the wall socket and wait until the device has cooled down.
Do not use cleaning solvents or abrasives.
Do not clean the inside of the device.
Do not attempt to repair the device. If the device does not operate correctly, replace it with a new device.
Clean the device using a soft, damp cloth. Thoroughly dry the device with a clean, dry cloth.
Use a vacuum cleaner with brush nozzle to remove dust from the airfow outlet.
Clean the filters under warm water with a neutral detergent. Do not dry the filters in direct sunlight.