en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡...
Safety en 1.4 Safe installation WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Connect the appliance to a power supply with alternating cur- rent only via a properly installed socket with earthing. ▶...
Page 6
en Safety WARNING ‒ Risk of injury! The high weight of the appliance may result in injury when lifted. ▶ Do not lift the appliance on your own. If this appliance is not correctly installed in a washer-dryer stack, the installed appliance may fall. ▶...
Safety en ▶ Wear protective gloves when installing and transporting the ap- pliance. 1.5 Safe use WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. ▶ Never operate a damaged appliance. ▶ Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
Page 8
en Safety WARNING ‒ Risk of poisoning! Detergents and care products may result in poisoning if con- sumed. ▶ If accidentally swallowed, seek medical advice. ▶ Keep detergents and care products out of the reach of children. WARNING ‒ Risk of explosion! Laundry that has been pretreated with cleaning agents that con- tain solvents may cause an explosion in the appliance.
Safety en 1.6 Safe cleaning and maintenance WARNING ‒ Risk of electric shock! Incorrect repairs are dangerous. ▶ Only use genuine spare parts when repairing the appliance. ▶ If the power cord of this appliance is damaged, it must be re- placed by the manufacturer, the manufacturer's Customer Ser- vice or a similarly qualified person in order to prevent any risk.
en Preventing material damage If the water pressure is too high or 2 Preventing material too low, the appliance may not be able to operate properly. damage Ensure that the water pressure in ▶ the water supply system is at least ATTENTION! 100 kPa (1 bar) and max.
Environmental protection and saving energy en Set the maximum spin speed if you 3 Environmental protec- want to dry the laundry in the tumble tion and saving energy dryer afterwards. a The drier the laundry, the shorter the programme duration when dry- 3.1 Disposing of packaging ing which, in turn, reduces energy consumption.
en Installation and connection Replace the accessories in ques- ▶ 4 Installation and con- tion before operating the appli- ance. nection → "Accessories", Page 29 Note: The appliance has been tested 4.1 Unpacking the appliance at the factory to check it is in working order. As a result, water stains may ATTENTION! remain in the appliance.
Page 13
Installation and connection en ATTENTION! Installation loca- Requirements If residual water in the appliance tion freezes, this may cause damage to Against a wall Do not trap the the appliance. power cord or Do not install or operate this appli- ▶ the hoses ance anywhere that is liable to ex- between the wall...
en Installation and connection Unscrew and remove all of Put on the 4 cover caps. the screws for the 4 transit bolts using a WAF 13 wrench. Push the 4 cover caps downwards. Remove the power cable from the holder. Note: To install the transit bolts to transport the appliance, perform these steps again in the reverse or- Remove the 4 sleeves.
Page 15
Installation and connection en Connect the water inlet hose to a Plastic pipe with Fix and secure tap (26.4 mm = 3/4"). rubber sleeve or the water outlet gully hose with an el- → Page 29. Connecting the appliance to the electricity supply Note: Your electrical domestic install- ation for this appliance must comply Open the water tap carefully and with the local legal provisions and...
en Installation and connection Use a WAF 17 wrench to tighten 4.6 Aligning the appliance the lock nuts against the housing In order to reduce noise and vibra- until they are hand-tight. tion and to prevent the appliance from moving, align the appliance cor- rectly.
Familiarising yourself with your appliance en 5 Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. On certain models, specific details such as the colour and shape may differ from those pictured. 5.2 Detergent drawer Maintenance flap for the drain pump → Page 38 Note: Observe the manufacturer's in-...
en Familiarising yourself with your appliance Manual dosing compartment : Dispenser for fabric softener : Dispenser for liquid deter- gent 5.3 Control panel You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. Programmes → Page 25 Programme selector → Page 30...
first time en Add washing powder that contains first time 6 Before using for the a bleaching agent to the manual dosing compartment. first time Prepare the appliance for use. first time 6.1 Starting an empty wash- ing cycle Your appliance was inspected thor- oughly before leaving the factory.
en Display 7 Display The display shows the current settings, options or relevant information. Example: Display Display Description 0:40 Expected programme duration or programme time re- maining in hours and minutes. Program end time → "Buttons", Page 23 10.0 Recommendation for the maximum load capacity for the selected program in kg.
Page 21
Display en Display Description Spin Programme status Program end Programme status ¡ Lights up: The childproof lock is activated. ¡ Flashes: The childproof lock is activated and the appli- ance has been operated. → "Deactivating the childproof lock", Page 32 (Easy Iron) The crease-reduction function is activated.
Page 22
en Display Display Description The detergent drawer has not been pushed in fully. E:35 / -10 Error code, error display, signal. → "Troubleshooting", Page 42 Example...
Buttons en 8 Buttons The selection of programme settings depends on the programme that is set. Button Selection More information Start/Reload ¡ Start Start, cancel or pause the pro- gramme. ¡ Cancel ¡ Pause Speed Perfect ¡ Activate Activate or deactivate a shorter pro- gramme duration.
Page 24
en Buttons Button Selection More information Prewash ¡ Activate Activate or deactivate prewash, e.g. for washing heavily soiled laundry. ¡ Deactivate Note: If the intelligent dosing system is activated, the detergent will be dis- pensed automatically for the prewash and the main wash. If the intelligent dosing system is de- activated, place the detergent for the prewash directly in the drum.
Programmes en 9 Programmes Note: The laundry's care labels provide you with additional information on pro- gramme selection. Programme Description Max. load (kg) Đồ cotton Wash hard-wearing items made from cotton, linen 10.0 Cottons or blended fabrics. Also suitable as a short programme for normally soiled laundry when you activate ...
Page 26
en Programmes Programme Description Max. load (kg) Programme setting: ¡ Max. 40 °C ¡ Max. 800 rpm Đồ len Hand- or machine-washable items that are made Wool from wool or contain wool. To prevent the laundry from shrinking, the drum moves the items very gently with long pauses.
Page 27
Programmes en Programme Description Max. load (kg) Tự động 40ºC Wash hard-wearing items made from cotton, or syn- Automatic 40ºC thetic or blended fabrics. The degree of soiling and the type of fabric are automatically detected. The washing process is ad- apted.
en Programmes Programme Description Max. load (kg) Nhanh 15'/30' Wash items made from cotton, or synthetic or blen- Super Quick ded fabrics. 15'/30' Short programme for small items of lightly soiled laundry. The programme duration is approx. 30 minutes. If you wish to reduce the programme duration to 15 minutes, activate ...
Accessories en 10 Accessories Use original accessories. These have been made especially for your appliance. Order num- Water inlet hose ex- Extend the water inlet hose for cold water WMZ2381 tension or AquaStop (approx. 2.50 m). Fixing brackets Improves the stability of the appliance. WMZ2200 Elbow Secure the water outlet hose in place.
en operation 13.4 Loading laundry operation 13 Basic operation Note: To prevent creasing, note the operation maximum load for the programmes. 13.1 Switching on the appli- → "Programmes", Page 25 ance Requirements ¡ The laundry is prepared and sor- Requirement: The appliance has ted. been correctly installed and connec- → "Laundry", Page 29 ted.
operation en a The drum rotates and load detec- The appliance door remains tion takes place. This can take up locked for safety reasons if the to 2 minutes, after which water temperature and water levels are enters the drum. high. a The display shows the programme –...
en Childproof lock This function is available depending 14 Childproof lock on the selected programme and is activated automatically. Secure your appliance against being Note operated unintentionally using the If you are using the intelligent dosing controls. system, do not add additional deter- gent or fabric softener into the com- 14.1 Activating the childproof partment for manual dosing.
Intelligent dosing system en To replace the contents of the dis- Open the dispenser cover. penser with another product, clean the detergent drawer. → "Cleaning the detergent drawer", Page 37 If required, adjust the contents of the dispenser. If required, adjust the basic dosage → Page 34.
en Intelligent dosing system 15.3 Basic dosage The basic dosage depends on the manufacturer's instructions for the de- tergent, the water hardness and the degree of soiling of the laundry. Always set a basic dosage that cor- responds to the dosage for a stand- ard load of 4.5 kg.
Basic settings en 16 Basic settings You can configure the basic settings for your appliance to meet your needs. 16.1 Overview of the basic settings Basic setting Programme Value Description position End signal 0 (off) Set the volume of the signal at the 1 (quiet) end of the programme.
en Cleaning and servicing 16.2 Changing the basic set- 17 Cleaning and servi- tings cing Set the programme selector to po- To keep your appliance working effi- sition 1. ciently for a long time, it is important to clean and maintain it carefully. 17.1 Cleaning the drum CAUTION Risk of injury!
Cleaning and servicing en Remove the pump unit. 17.2 Cleaning the detergent drawer If you want to replace the liquid de- tergent or fabric softener in the dis- penser with another product or if the detergent drawer is dirty, clean the detergent dispenser. ATTENTION! The pump unit contains electrical components.
en Cleaning and servicing Clean the pump unit with a damp cloth. Clean the housing of the detergent drawer in the appliance. Clean the detergent drawer and the cover with a soft, damp cloth or hand shower. Push in the detergent drawer. 17.3 Cleaning the drain pump Dry the detergent drawer, cover Clean the drain pump regularly, at...
Page 39
Cleaning and servicing en Open and remove the mainten- CAUTION - Risk of scalding! ance flap. When you wash at high temperat- ures, the detergent solution gets hot. Do not touch the hot detergent ▶ solution. To allow the detergent solution to flow out into the container, remove the sealing cap.
Page 40
en Cleaning and servicing Insert the pump cap. Cleaning the drain pump Requirement: The drain pump is empty. → Page 38 Since water may remain in the drain pump, unscrew the pump cap carefully. Screw the pump cap as far as it will go. Clean the interior, the thread on the pump cap and the pump hous- ing.
Page 41
Cleaning and servicing en Insert the mains plug. Before the next wash Switch on the appliance. To prevent unused detergent from Pour 1 litre of water into the flowing straight into the outlet in the manual dosing compartment. next wash, run a suitable programme for draining after you have emptied Select a suitable programme for the drain pump.
en Troubleshooting 18 Troubleshooting WARNING Risk of electric shock! Improper repairs are dangerous. Only use genuine spare parts when repairing the appliance. ▶ If the power cord of this appliance is damaged, it must be replaced by the ▶ manufacturer, the manufacturer's Customer Service or a similarly qualified person in order to prevent any risk.
Page 43
Troubleshooting en Fault Cause and troubleshooting "E:36 / -10" If you dose manually, reduce the amount of deter- ▶ gent for the next washing cycle with the same load. "E:10 / -00 / -10 / The pump for the intelligent dosing system is blocked. -20"...
Page 44
en Troubleshooting Fault Cause and troubleshooting The detergent drawer has not been pushed in fully. Push in the detergent drawer until the symbol goes ▶ out. The pump unit is not inserted. Insert the pump unit into the detergent drawer. → "Cleaning the detergent drawer", Page 37 Push in the detergent drawer until the symbol goes out.
Page 45
Troubleshooting en Fault Cause and troubleshooting The appliance is not The mains plug of the power cord is not plugged in. working. Connect the appliance to the power supply. ▶ The circuit breaker in the fuse box has tripped. Check the circuit breaker in the fuse box. ▶...
Page 46
en Troubleshooting Fault Cause and troubleshooting The door cannot Select a suitable programme for draining. ▶ be opened. → "Programmes", Page 25 Power failure. Open the door using the emergency release. ▶ → "Emergency release", Page 53 The water is not drain- Drain pipe or water outlet hose is blocked. ing.
Page 47
Troubleshooting en Fault Cause and troubleshooting Water is not flowing Turn on the tap. ▶ in. Detergent is not The water inlet hose is kinked or jammed. being dispensed. Ensure that the water inlet hose is not kinked or ▶ jammed. The spin cycle runs The unbalanced load detection system eliminates an several times.
Page 48
en Troubleshooting Fault Cause and troubleshooting Drum rotates, water Load detection is active. does not flow in. Not a fault – no action required. ▶ Note: The load detection can take up to two minutes. Heavy foam build-up Detergent dosage is too high. Immediate measure: Mix one tablespoon of fabric ▶...
Page 49
Troubleshooting en Fault Cause and troubleshooting The spin programme The unbalanced load detection system has interrupted does not start. the spin cycle because the laundry is unevenly distrib- uted. Redistribute the laundry in the drum. ▶ Note: Where possible, mix large and small items in the drum.
Page 50
en Troubleshooting Fault Cause and troubleshooting The spin result is not A low spin speed is selected. satisfactory. The laun- The next time you run a wash cycle, set a higher ▶ dry is too wet/too spin speed. damp. Start the Vắt programme. ▶...
Page 51
Troubleshooting en Fault Cause and troubleshooting Detergent residue on If intelligent dosing is activated, reduce the basic ▶ the damp washing. dosage → Page 34. Detergent residue on Detergents may contain water-insoluble substances the dry laundry. that deposit on the laundry. Brush out the laundry after washing and drying. ▶...
Page 52
en Troubleshooting Fault Cause and troubleshooting Water is leaking out at Water inlet hose is not correctly/securely connected. the water inlet hose. Connect the water supply hose correctly. → "Connecting the water inlet hose", Page 14 Tighten the screw connection. Water is leaking out at The water outlet hose is damaged.
Transportation, storage and disposal en 18.1 Emergency release 19.2 Inserting the transit bolts Releasing the door Secure the appliance before trans- Requirement: The drain pump is portation using transit bolts in order empty. → Page 38 to prevent transport damage. ATTENTION! Escaping water may Use a screwdriver to remove the 4 cause material damage.
en Customer Service 19.4 Disposing of old appli- 20 Customer Service ance Detailed information on the warranty Valuable raw materials can be re- period and terms of warranty in your used by recycling. country is available from our after- sales service, your retailer or on our WARNING website.
Technical data en Weight 81.3 kg Water pressure ¡ Minimum: 100 kPa Maximum load 10.0 kg (1 bar) Mains voltage 220-240 V, ¡ Maximum: 50 Hz 1000 kPa Minimum in- 10 A (10 bar) stallation protec- Length of the wa- 150 cm tion ter inlet hose Nominal power 1900-2300 W Length of the wa- 150 cm ter outlet hose Length of the...
Page 56
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.