Summary of Contents for SimpleTech STI-17ESH2
- Page 1 Cellphone Cables and Drivers STI-17ESH2 STI-17FJH2 STI-17MBH1 STI-17MOH1 STI-17MOH2 STI-17MOH3 STI-17NCH1 STI-17NCH3 STI-17NCH4 STI-17OKH1 STI-17OKH2 STI-17OKH3 STI-17NKH1 STI-17NKH2...
-
Page 2: Table Of Contents
Introduction ... 3 1. Select the appropriate CellPhone Cable ... 3 2. Connect cellphone cable with the modem ... 5 3. Installation Procedure for Cellphone Driver ... 6 3A . Installation Procedure for Win 3.1x or Win 95 ... 6 Running Modem Upgrade Utility ... -
Page 3: Introduction
To order a cellphone cable, look up the Part Number for the cable specific to your cellphone. Then order the cable through your Simple Technology dealer. For a Simple Technology dealer near you, contact Simple Technology at 1(800) 367 7330 or (714) 476-1180 or support@simpletech.com. List of Cellphone Cables Cellphone Manufacturer AT&T... - Page 4 P110, P120, P180, Sport P200, P201, P300, P301 P700 Series, P800 Series 2120, 2160, 2168 900, 910 1145, 1150 1300, 1325, 1335, 1375 700, 720 900, 920 Cellphone Cable STI Part Number STI-17ESH2 STI-17ESH2 STI-17ESH2 STI-17ESH2 STI-17ESH2 STI-17ESH2 STI-17ESH2 STI-17FJH2 STI-17ESH2 STI-17ESH2 STI-17ESH2...
-
Page 5: Connect Cellphone Cable With The Modem
2. Connect cellphone cable with the modem Attach the Cellphone cable to the Simple Technology modem PC Card as shown below. Then insert the PC card modem in the PCMCIA socket. Do not connect the Cellphone cable to the PC Card modem until the installation of CellPhone driver is done as indicated in the following chapter. -
Page 6: Installation Procedure For Cellphone Driver
Installation Procedure for Cellphone Driver Make sure the PC Card modem is inserted in the PCMCIA slot. Install the CellPhone driver as described below. 3A . I nstallation Procedure for Windows 3.1x or Windows95 Proceed as follows: 1. Install the modem communication software, if not already installed, as described in the User Guide that came with the modem. -
Page 7: Running Modem Upgrade Utility
7. When the following screen appears, click continue to install the modem upgrade utility in c:\modem directory. 8. After the installation of the utility is complete, the following screen appears and a program group icon “Modem Upgrade Utility” is created as shown below. Running Modem Upgrade Utility Make sure the PC Card modem is inserted in the PCMCIA slot. - Page 8 The software will test for presence of modems on different COM ports. If the following message appears, click Yes to continue. When the following message appears, click on Yes. Page 8...
- Page 9 10. The Load Driver window appears as shown below. Select the appropriate cellphone model and Firmware list (e.g., Select 1510C_US.336 for 33.6 kbauds) and click on load driver. The driver is downloaded into the modem flash memory. This takes from five to ten minutes.
- Page 10 12. Once the appropriate drivers are loaded and the modem is reset, the following message appears to indicate that the firmware upgrade is complete. Click OK. Congratulations! The cellphone driver update installation for PC Card modem is complete. The AutoLine setup will automatically detect whenever you use the modem with a cellphone.
-
Page 11: Using The Cellphone With Cellphone Cable
4. Using the CellPhone with Cellphone cable Switch off the CellPhone, insert the modem PC Card in the PCMCIA slot and connect the Cellphone to the modem using the cellphone cable. Then switch on the CellPhone and Use the modem as directed in the documenta- tion that came with the modem. - Page 12 CellPhone connection icon, go to file and click on proprieties. This will show how the connection is currently setup. 4. First verify that the correct modem is selected. Next click on Configure. On the cellular connection, it is advisable to turn down the baud rate to around 19200 bps.
- Page 13 is to be established, is to set the dialup connection to bring up a pre-dial up terminal window. This is checked under the OPTIONS tab. This allows the user to issue AT commands to verify a stable connection. 6. Now that these changes have been made, you are ready to connect. Plug the cell phone cable into the modem and into the cell phone, turn the phone on and launch your Dial-up networking account.
- Page 14 modem is responding and is ready to connect via cellular. First type AT and press enter on your keyboard. You should receive the response OK. This tells you that the modem is ready and is waiting further instructions. Now type AT^T6. You should receive one of the following responses: 000 = Cellular driver loaded, no cellular cable attached to the modem.
-
Page 15: Technical Support
If you are experiencing difficulties with the installation or have any questions regarding the cellphone cable and driver, contact Technical Support at the following : • Tel: 714-476-1180 • 1-800-367-7330 (US & Canada only) • Fax: 714-476-1209 • Email: support@simpletech.com • Web: http://www.simpletech.com Page 15... - Page 16 STI to notify any person of such revision. Products and brand names are trademarks and/or registered trademarks of their respective companies. 1-800-367-7330 3001 Daimler Street, Santa Ana, California 92705 Tel: (714) 476-1180 Fax: (714) 476-1209 WebSite: http://www.simpletech.com Page 16 60000-00010-011...