• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
HSB-600(A) 2006.4.25 12:29 PM 페이지 3 1. Read Instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.
Page 5
HSB-600(A) 2006.4.25 12:29 PM 페이지 4 FOR YOUR SAFETY Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. U.S.A CAUTION 120 V...
HSB-600(A) 2006.4.25 12:29 PM 페이지 5 CONTENTS Introduction • READ THIS BEFORE OPERATING YOUR UNIT • SAFETY INSTRUCTIONS • ACCESSORIES | 5 Part Names and Functions • FRONT PANEL • BACK PANEL • REMOTE CONTROL • REMOTE CONTROL OPERATION RANGE •...
HSB-600(A) 2006.4.25 12:29 PM 페이지 6 Part Names and Functions FRONT PANEL 1. POWER (ON/STANDBY) button Each time the POWER button is pressed, this unit is turned on to enter the operating mode or off to enter the standby mode. 2.
HSB-600(A) 2006.4.25 12:29 PM 페이지 7 REMOTE CONTROL OPERATION RANGE LOADING BATTERY Remove the cover. • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. Load the battery(CR2025) matching the polarity.
HSB-600(A) 2006.4.25 12:29 PM 페이지 8 System Connections • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to observe the color coding when connecting component cords. • Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to this unit. •...
Page 10
In such a case, make the digital audio connection(and the analog audio connection if needed) between the source equipment and the display equipment(or A/V amp, receiver). Connecting the display equipment with the DVI IN connector • If your display equipment has the DVI IN connector compatible with DVI and High-bandwidth Digital Content Protection (HDCP), connect it to the HDMI OUT connector of this unit using a commercially available HDMI- DVI converter cord.
Since the HDMI-to-DVI connection cannot carry audio signals, you should make the digital audio connection(and the analog audio connection if needed) between the source equipment and the display equipment (or A/V amp, receiver) Connecting the display equipment • For details on how to connect the display equipment, refer to "Connecting the display equipment with the HDMI IN connector"...
In such a case, connect the IR IN jack to the output of the connecting block. Note: • Remote operation may become unreliable if the IR receiver is exposed to strong light such as direct sunlight or inverted fluorescent. 4. RS-232C •...
HSB-600(A) 2006.4.25 12:29 PM 페이지 12 Operations Turn the power on. • Each time the POWER(ON/STANDBY) button on the front panel is pressed, this unit is turned on to enter the operating mode (the STANDBY indicator lights up in bule) or off to enter the standby mode (the STANDBY indicator lights up in red).
Video Interface (DVI) by encrypting its transmission between the video source and the digital display (receiver). The video source might be a computer, set-top box, or digital versatile disc (DVD) player, and the digital display might be an liquid crystal display (LCD), television, plasma panel, or projector.
HSB-600(A) 2006.4.25 12:29 PM 페이지 14 Troubleshooting Guide If a fault occurs, run through the table below before taking your unit for repair. If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your dealer.
HSB-600(A) 2006.4.25 12:29 PM 페이지 15 Specifications • Digital input/output level Optical, 660 nm -21~ -15 dBm • Component video input sensitivity, 75 Ω (75% color bar) R-Y signal B-Y signal Y signal • HDMI 19 pin Picture resolution Audio sampling frequency •...