Scotsman CME306 User Manual
Scotsman cme306 ice machine: user guide
Hide thumbs
Also See for CME306:
- Technical training manual (58 pages) ,
- Product manual (40 pages) ,
- User manual (33 pages)
Advertisement
Quick Links
HD150
Introduction
To the owner or user: This product manual is a
source of information about the installation, start
up, cleaning, maintenance and repair of the
product.
The HD150 is a hotel/motel ice dispenser. It is
designed to use a Scotsman CME306 or CME456
ice machine as the source for ice.
Ice from the cuber falls into the insulated hopper,
where it is stored until needed. When a user
pushes the dispense button a rotating wheel
scoops the ice up to the top front of the hopper
where there is an outlet to the ice chute.
Table of Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Final Check List/Initial Start Up/Electrical Sequence
. . . . . . . . . . . . . . . page 7
Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Parts lists and wiring diagrams are located in the
center of this manual, printed on yellow paper.
Note the warning symbol where it appears in this
manual. It is an alert for important safety
information on a hazard that might cause serious
injury.
Keep this manual for future reference.
This manual was printed on recycled paper.
May 2000
Page 1
Advertisement
Related Manuals for Scotsman CME306
Summary of Contents for Scotsman CME306
-
Page 1: Table Of Contents
The HD150 is a hotel/motel ice dispenser. It is designed to use a Scotsman CME306 or CME456 ice machine as the source for ice. Ice from the cuber falls into the insulated hopper, where it is stored until needed. -
Page 2: Specifications
F. air maximum. Must be installed indoors. Must allow space to the right for air intake when using air cooled ice machine. Compatible only with Scotsman CME306 or CME456 brand models. Must allow space for utility connections at the back. -
Page 3: Installation
Check that gasket tape is on the top outside edge of Thread the legs into the base of the dispenser. Be the dispenser where the ice machine will rest. sure that the legs are screwed in all the way. Turn the leg levelers in all the way. - Page 4 There is no thermostat to install. Place the ice machine (CME306 or CME456) onto the top of the HD150. The ice machine will sense when ice builds up into its cube port and shut off. It automatically restarts when that ice is removed.
-
Page 5: Kits
A kit is available to install a coin mechanism, and another kit is available to install a room key mechanism. Both come with detailed instructions, summarized here: Coin Mechanism, install after ice machine has been operating: 1. Disconnect electrical power. Electrical Shock Hazard. - Page 6 Key Kit Installation: (KSLDK2) 1. Disconnect electrical power Electrical Shock Hazard. Disconnect electrical power before beginning procedures. 2. Remove sink and drain pan. 3. Remove cover. 4. Remove control box cover 5. From kit, locate brass fitting. Obtain typical door lock cylinder from the motel/hotel.
-
Page 7: Electrical Sequence
6. Check that the sink key, and coin box key if used, are available. To Start: 1. Connect electrical power. 2. Go thru ice machine start up procedures. Let ice machine make two harvests. 3. Push vend switch button in. 4. Rotor should rotate 1/4 turn and stop. - Page 8 HD150 Operational Schematic Ice Machine Ice Chute Gear Motor Sink Storage Bin Drain Pan Drain Condensate Pan May 2000 Page 8...
-
Page 9: Cleaning
3. Locate key and remove sink. 4. Remove top front panel (in front of ice machine). 5. Remove the front top panel (above ice chute). 6. Reach into the opening, locate the large nut securing the wheel to the drive shaft. Remove the nut. -
Page 10: Service Diagnosis
Ice door does not open Drive shaft broken Does not vend, no ice Bin drain leaks May 2000 Page 10 HD150 PROBABLE FIX Check ice machine Check power supply Check/replace vend switch Check/replace sink interlock switch Machine is not level Reinstall panel Check/replace gearmotor Check for power to solenoid. -
Page 11: Removal And Replacement
2. Disconnect electrical power 3. Locate key and remove sink. 4. Remove top front panel (in front of ice machine). 5. Remove the front top panel (above ice chute). 6. Reach into the opening, locate the large nut securing the wheel to the drive shaft.