NEC MDview Series User Manual page 22

V.RESOLUTION
EXPANSION
SIDE BORDER
COLOR
Tag6 USB SELECTION
EDID EXTENSION
(Digital Input Only)
VIDEO DETECT*
OFF TIMER
OFF MODE
OFF MODE SETTING Adjusts the ILLUMINANCE value for OFF MODE. Shows illuminance.
LED BRIGHTNESS*
LED COLOR*
Tag7 LANGUAGE*
OSD H.POSITION
*2 This item will not be reset by FACTORY PRESET (Tag7).
Adjusts the vertical size by increasing or decreasing the setting.
Press "Right" button to expand the height of the image on the screen.
Press "Left" button to narrow the height of the image on the screen.
Sets the zoom method.
FULL: The image is expanded to full screen, regardless of the resolution.
ASPECT: The image is expanded without changing the aspect ratio.
OFF: The image is not expanded.
CUSTOM: When CUSTOM is selected as the Expansion mode, it becomes possible to
adjust the H. ZOOM., V. ZOOM, and ZOOM POS.
Adjusts the side black bars color between black and white.
USB UP Stream Port Selection for DP/DVI-1/DVI-2/D-SUB. When connecting a computer
to each of the upstream ports, the monitor's USB downstream ports can be used by
selecting this setting for the current input signal. When using only one upstream port, the
connected upstream port is active.
You can change the active display and upstream USB port combination by using the
Input button (see page 9).
NOTE: To avoid data loss, before changing USB upstream ports, ensure that no USB
storage devices are in use by the operating system of the computer attached to the USB
upstream port.
A communication setting with input device, containing signal timing.
NORMAL: When a PC or other computer equipment is connected, select "NORMAL".
Enhanced: Alternate setting for non-PC devices such as DVD players or game consoles.
Note: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems,
please refer to the Troubleshooting section of this User's Manual.
When EDID EXTENSION has been changed, the connected equipment has to be
restarted.
2 Selects the method of video detection when more than one computer is connected.
Press "Left" or "Right" to select.
FIRST: When current video input signal is not present, then the monitor searches for
a video signal from the other video input port. If the video signal is present in the other
port, then the monitor switches the video source input port to the new found video source
automatically. The monitor will not look for other video signals while the current video
source is present.
LAST: When the monitor is displaying a signal from the current source and a new
secondary source is supplied to the monitor, then the monitor will automatically switch to
the new video source. When current video input signal is not present, then the monitor
searches for a video signal from the other video input port. If the video signal is present
in the other port, then the monitor switches the video source input port to the new found
video source automatically.
NONE: The Monitor will not search the other video input port unless the monitor is
turned on.
Monitor will automatically turn off after the preset time period from power on with the
ON/OFF function. When you select "ON", press "SELECT" and "Left" or "Right" to adjust.
Before powering off, a message will appear on the screen asking the user if they want to
delay the turn off time by 60 minutes. Press any OSD button to delay the turn off time.
The Intelligent Power Manager allows the monitor to enter into a power saving mode after
a period of inactivity. The OFF MODE has three settings.
OFF: Monitor does not go into power save mode when the input signal is lost.
STANDARD: Monitor enters power save mode automatically when the input signal is lost.
OPTION: Monitor enters power save mode automatically when the amount of
surrounding light goes below the level that is determined by the user.
2
Controls the brightness of the power LED on the monitor.
2 Toggles the power LED on the front between blue or green.
2
OSD control menus are available in nine languages. Press "Left" or "Right" to select.
You can choose where you would like the OSD control image to appear on your screen.
Selecting OSD Location allows you to manually adjust the position of the OSD control
menu left or right.
English-20