Advertisement
CONNECTIONS AND ADJUSTMENTS
b Attaching the lens
Use any DC type and CS mount lens equipped with an auto iris (sold separately).
1
3
• Depending on the type of the lens, the shape of
Pin layout for LENS terminal
the lens plug may differ. In this case, consult your
Brake coil (–)
Drive coil (+)
dealer or an Authorized Sanyo Service Center.
• Apply adapter ring (sold separately) when you use
Brake coil (+)
Drive coil (–)
any C mount lens.
b Supported coaxial cables
Cable type – Length:
• RG-59U (3C-2V) – 250 m/273 yd max.
• RG-6U (5C-2V) – 500 m/547 yd max.
• RG-11U (7C-2V) – 600 m/656 yd max.
• When using an RG-59U (3C-2V) cable, do not use it on piping or air
wiring.
• If you use a cable other than the type above, the image or sync signal will
be attenuated and will not be transmitted correctly.
Monitor
: VIDEO IN
Digital video recorder
: VIDEO OUT
b Power cable
<AC 24 V connection>
<DC 12 V connection>
GND AC24V
DC12V
To prevent a fire hazard use any UL
Check that polarity is correct.
listed wire rated VW-1.
b Camera attachment
When attaching the camera, make sure to verify that the attachment surface will allow full
tightening of the screws. Plaster board, etc., may not give a strong enough attachment, and
it is recommended to use a reinforcement, or other method so that the screws are anchored
2 2
securely.
• When monitoring lighting or other extremely bright objects
5 mm/0.2 in. max.
(which exceed the maximum required illumination),
smearing may occur in the vertical or horizontal direction
(either above and below the high-brightness object or as a
perpendicular band). In such a case, adjust the angle of
illumination and other factors while observing the monitor.
• You can change the bracket topside down. Make sure to
use the longer screws A to secure the bracket.
b Camera adjustments/settings
The camera comes pre-adjusted and ready to install at the
time of factory shipment, but you can make adjustments or
settings if you need.
If you have trouble adjusting the camera, consult your dealer
or an Authorized Sanyo Service Center.
VIDEO OUT
POWER
BLC
D/N
ON
CENT
EI
MULTI
AI
OFF
GND AC24V
DC12V
B Camera screws (shorter)
A Bracket screws (longer)
1
Iris setting (EI/AI)
EI (Electronic Iris)
When using a manual or fixed
iris lens and the electronic iris
function is on
• For indoor use
NOTE on EI setting:
• Set the lens aperture to the shortest F stop.
• If fluorescent lighting is used where the camera is installed, the
LL
object will flicker as a result. This type of phenomenon can be
MANU
avoided by replacing the fluorescent lighting with incandescent
L
H
lamps.
• If the light entering the lens exceeds the maximum required
illumination, the image cannot be displayed properly. In that
INT
R
WB
B
PHASE
LEVEL
ATW
case, manually adjust the lens iris.
NOTE on AI setting:
If the entire image is too dark or too bright, adjust the contrast
using the LEVEL dial.
• L (Counterclockwise):
Closes the lens iris, making the entire image darker.
• H (Clockwise):
Opens the lens iris, making the entire image brighter.
2
Day/Night function (D/N)
ON
Automatically switches to
B/W (non-IR sensitive) to
optimize low light surveillance
b Flange-back adjustment
This normally does not need adjustment. If the picture is out of focus at the telephoto
position, adjust the flange-back position as described below.
1
Loosen.
4
Tighten.
A
2
Set to the maximum telephoto
position and focus the picture.
B
Repeat steps 2 and 3 until the image stays in-focus when changing from a wide-angle position to
a telephoto position.
3
Backlight compensation
(BLC)
AI (Auto Iris)
Only when using an auto-iris lens
When using an auto-iris lens
MULTI
(Multi-spot metering)
Backlight compensation
L
H
to the entire screen*
High
1
1
LEVEL
3
* If the background of the object is extremely dark, set to Center zone
metering.
4
White balance (WB)
MANU
(Manual white balance)
5
5
Sync setting (LL/INT)
LL (Line-Lock)
(Only when using an AC power supply)
Synchronizes the unit with power
frequency*
B/W
B/W
Color
Color
Switchover point
* Adjust the roll by turning the PHASE dial on the second and subsequent
cameras.
OFF
If the vertical roll cannot be corrected by adjusting the
Color images only
PHASE dial on the second and subsequent cameras, try
adjusting the PHASE dial on the first camera. If it still cannot
be corrected, please check that the polarity of the power
cords of all connected devices is correct.
2
2
Français
English
3
Set to the maximum
wide-angle position
and focus the
picture.
CENT
(Center zone metering)
Backlight compensation
OFF
to the central portion of
the screen
Normal
4
3
4
3
4
3
4
ATW
(Auto-Tracing
White balance)
Turn clockwise to
augment the color.
5
R
WB
B
INT
(Internal sync)
6
6
PHASE
Advertisement
