Table of Contents
Advertisement
Quick Links
Click anywhere ON THIS PAGE to return to Water Softener information at InspectApedia.com
Use & Care Guide
Manual de Uso y Cuidado
English / Español
Kenmore
Model / Modelo No. 625.383000
Water Softener
with High Flow Valve
Ablandador de Agua
con válvula de alto flujo
Sears Brands Management Corporation
3333 Beverly Road
Hoffman Estates, IL 60179 U.S.A.
www.kenmorewater.com
www.kenmore.com
www.sears.com
®
System tested and certified by NSF
International against NSF/ANSI Standard 44
for hardness reduction and efficiency.
Este sistema ha sido probado y certificado
por NSF International de acuerdo a
Norma NSF/ANSI 44
para la reducción de la dureza y eficiencia.
Printed on recycled paper/
Impreso en papel reciclado
P/N 7324976 (Rev. B 1/31/11)
Advertisement
Table of Contents
Related Manuals for Sears Kenmore 625.383000
Summary of Contents for Sears Kenmore 625.383000
- Page 1 Kenmore Model / Modelo No. 625.383000 Water Softener ® with High Flow Valve Ablandador de Agua con válvula de alto flujo Sears Brands Management Corporation 3333 Beverly Road Hoffman Estates, IL 60179 U.S.A. www.kenmorewater.com www.kenmore.com www.sears.com Printed on recycled paper/ Impreso en papel reciclado P/N 7324976 (Rev.
-
Page 2: Warranty
Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential dam- ages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential dam- ages, or limitation on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you. -
Page 3: Table Of Contents
Table of Contents Warranty ..................2 Safety Guides . -
Page 4: Specifications & Dimensions
Specifications & Dimensions Model No. 625.383000 Model Code 8,300 @ 1.7 lbs. Rated Softening Capacity (Grains @ Salt Dose) 20,400 @ 6.5 lbs. 24,400 @ 11.0 lbs. Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose) 4,880 @ 1.7 lbs. Rated Service Flow Rate 7.3 gpm Amount of High Capacity Ion Exchange Resin... -
Page 5: Packing List
Packing List The parts required to assemble and install the water Remove and discard (or recycle) all packing materials. softener are included with the unit. Thoroughly check To avoid loss of small parts, we suggest you keep the the water softener for possible shipping damage and small parts in the parts bag until you are ready to use parts loss. - Page 6 6. Put the softener in a place where water damage is (city water). least likely to occur if it develops a leak. Sears or the manufacturer will not repair or pay for water 2. Place as close as possible to a water drain such as a damage.
-
Page 7: Installation
Plan Your Installation CHECK YOUR WATER PRESSURE BEFORE INSTALLING For your water softener to work properly, incoming psi, buy and install a pressure reducing valve in the water pressure in your house pipes must be no lower pipe supplying water to the softener’s inlet. than 20 pounds per square inch (psi). - Page 8 Installation INSTALL SINGLE BYPASS VALVE (cont.) ASSEMBLE INLET AND OUTLET PLUMBING Before installing the bypass valve and/or installation Measure, cut (thread if needed) and put together all adaptors, make sure that the turbine and support are pipe and fittings up to the main water pipe. Make sure firmly in place inside the softener valve’s outlet port.
- Page 9 Installation CONNECT THE VALVE DRAIN HOSE COPPER DRAIN TUBE: Local plumbing codes may require the use a copper valve drain tube. A copper Take a length of 3/8” inside diameter drain tubing tube is also best to use if running a drain line overhead. (supplied) and attach one end to the drain fitting (see To adapt a copper drain tube to the softener, purchase Fig.
- Page 10 Installation LEAK TEST SINGLE BYPASS VALVE To check for leaks, complete the following steps: CAUTION: To avoid water or air pressure damage to softener inner parts, and to flush pipe chips Pull stem outward or other residue from the water pipes, be for Service sure to do the following steps exactly as instructed.
- Page 11 Installation INSTALL GROUNDING CLAMP METAL PIPE GROUNDING The house cold water pipe (iron or copper) is often used to ground all electrical outlets in the home. To maintain Valve Inlet this ground, use the ground clamp kit included in the parts bag.
-
Page 12: Programming The Softener
Up moves the display ahead; down bed at least every 6 months. Your local Sears sets the time back. Be sure AM or PM is correct. store has Water Softener Cleaner (Part Number 34427) available. - Page 13 Programming the Softener SET RECHARGE (REGENERATION) START TIME SET SALT LEVEL The water softener has a salt monitor indicator light to If you completed the previous step, the words “SET RE- remind you to add salt to the storage tank. CHARGE TIME"...
-
Page 14: Sanitizing The Water Softener
1. Open salt lid, remove the brinewell cover and pour faucet. about 3 oz. (6 tablespoons) of household bleach into Your new Sears softener is now softening the water for the softener brinewell. Replace the brinewell cover. your household needs. However, your WATER HEATER 2. -
Page 15: Controller Features
Controller Features EXTRA RECHARGE SALT MONITOR SYSTEM Sometimes, a manually initiated recharge (regeneration) The water softener has a salt monitor indicator light to may be desired, or needed. Two examples are: remind you to add salt to the storage tank. NOTE: You must set salt level each time salt is added You have used more water than usual (guests visiting) and you may run out of soft water before the next... - Page 16 Controller Features EFFICIENCY MODE BACKWASH & FAST RINSE TIMES When this feature is ON, the water softener will oper- If you experience salty tasting water after regeneration, ate at salt efficiencies of 4000 grains of hardness per you may need to increase the backwash and fast rinse pound of salt or higher.
-
Page 17: Care Of Your Water Softener
Care of Your Water Softener SALT BRIDGE Push tool into Sometimes, a hard crust or salt “bridge” forms in the salt bridge brine tank. It is usually caused by high humidity or the to break wrong kind of salt. When the salt “bridges,” an empty space forms between the water and the salt. -
Page 18: Service Information
If your water softener does not work properly, make the following easy checks. Often, you will find what is wrong yourself and you won’t have to call and wait for service. If you do not find anything wrong while making the checks, and your softener still does not work properly, call your Sears Service Department. PROBLEM... - Page 19 Service Information MANUALLY INITIATED ELECTRONIC DIAGNOSTICS 1. To enter diagnostics, press and hold the SELECT but- ton until “000 - -” shows in the display. Motor Position Sensor Figure 32 Housing Switch TURBINE OPERATION: If no water is flowing through Turbine the softener, the turbine indicator displays three zeros.
- Page 20 Service Information MANUAL ADVANCE REGENERATION CHECK This check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration flow rates, and Position Markers other controller functions. Always make the initial (valve in service) checks first, and perform the manually initiated elec- tronic diagnostics.
- Page 21 Notes Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com...
-
Page 22: Exploded View & Parts List
Water Softener Exploded View Kenmore Model No. 625.383000 Valve Assembly See Pages 24 & 25 for parts Rating Decal Location Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com... - Page 23 Softener Parts List Part No. Description Part No. Description 7275907 Transformer, 24V, 10VA 7327584 Repl. Bottom Distributor 7324926 Top Cover 0502272 Resin 7324934 Salt Lid (order decal below) 7327607 Repl. Resin Tank, 7” x 40” 7325029 Instruction Decal, English Distributor O-Ring Kit 7112963 (includes Key Nos.
- Page 24 Valve Assembly Exploded View Wear Strip Seal Cross-Section View Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com...
- Page 25 Valve Parts List Part No. Description Part No. Description 7224087 Screw, #8-32 x 1” (2 req.) 7082053 Valve Body 7286039 Motor (incl. 2 ea. of Key No. 50) 7081201 Retainer, Nozzle & Venturi 0900857 Screw, #6-20 x 3/8” (2 req.) 7170319 O-Ring, 1/4”...
- Page 26 Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries ® Marca Registrada / Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC en otros países Marque de commerce /...