Advertisement
Quick Links
Advertisement
Related Manuals for Sears 625.34929
Summary of Contents for Sears 625.34929
- Page 1 -- HOW TO INSTALL- Read All Safety Guides Before HOW IT WORKS- You Start to Install Your CARE OF- Dispensing System -- SPECIFICATIONS -- REPAIR PARTS-- SAVE THIS MANUAL Sears, Roebuck and Coo, Chicago, IL 60684 U.S.A. PRINTED IN U S A...
- Page 2 THE NEAREST SEARS applies only while this pro- rights which vary Chicago, IL 60684 talk to your Sears Salesman. Installers INSTALLATION WARRANTY to any war ranty extended to you on the involved, which warranty date merchandise the workmanship of any Sears...
- Page 3 If the water is not treated in some way, it may be useless, into the water is a good way to treat the water. Your Sears Solution Dispensing following kinds of water problems, SYSTEM IN AN ATTEMPT POLLUTED WATER.
- Page 4 If your water needs write your nearest Sears store for help_ CHECK YOUR WATER SUPPLY PRESSURE For your solution dispensing to work right, water system pressure than...
-
Page 5: Tools And Materials
TREATING WELL WATER PRE-TREATING PRIVATE WELL HAVING IRON BACTERIA -- Before dispensing system together and install inate the well if it contains more than 10 parts per million (ppm) of bacterial iron. steps. NOTE: If you don't chlorinate the well, have iron in your water for up to 2 months... - Page 6 PUT YOUR DISPENSING 1, Fasten the solution pump to the base with 4 nylon screws and nuts, as shown 2. Working through the tank fill hole, assemble Low Level Indicator to the tank as shown, upper window port so the red indicator 3.
- Page 7 42 gallon (or larger) tank, as shown in FIG. to get time. A blending tank is avail- Sears, Stock No. 42.34028o of all Solution Dispensing a blending tank is needed Solution mixing° A blending tank but in some (shallow...
- Page 8 I BLENDING TANK Pressure Tank BLENDING TANK 42 ga! minimum ' ,ill i -- separate inlet & outlet -- no air bag or diaphragm PRESSURE TANK INSTALLED "ON" THE MAIN SUPPLY LINE GUXDESTO nNSTALL YOUR (:_ SOLUTION INJECTION 1. Set the solution dispensing system you chose...
- Page 9 GUBDESTO BNSTALL YOUR S SOLUTION INJECTION INTO 1. Turn off the electrical power and turn off the gas or electric supply heater 2. Open a faucet for a few seconds, water pressure, then close 3. Close the shut-off valve on the main water close to the pressure tank NOTE:...
- Page 10 I GUIDES TO SOLUTION INJECTION 1. Turn off the electrical power and turn off the gas or electric heater, 2. Open a faucet a few seconds water pressure, then close 3o Close the shut-off valve on the main supply close to the pressure tank NOTE: If you...
- Page 11 ELECTRICAL WgRRNG GUIDE, € CAUTION: WIRING IF YOU TRICITY. CALL A GOOD ELECTRICIAN CAUTION: DO NOT DO ANY LIVE CIRCUITS ALWAYS TURN ELECTRICAL POWER AT THE SOURCE, NOTE: All wiring must follow electrical codes. 1. Looking at FIG.7and8or9, in a duplex, 3-prong, 115 volt "...
- Page 12 I RLL THE TANK WnTH THE SOLUTION DISPENSING VOIR (TANK) HOLDS 15 GALLONS HOWEVER, ON THE FIRST FILL, ALLOW ROOM IN THE TANK STRENGTH CAN BE CHANGED PENDING ON THE WATER PROBLEM TREATING, FILL THE TANK AND SET THE FEED RATE AS FOLLOWS.
- Page 13 TREATMENT voir (tank) cover and fill the tank with 8 gallons WARM water. Pour in 80 oz. (10 oz water) of Sears Neutralizing Compound, 42-34475. Stir until the compound solved, 1. Plug the pump power cord in and open a nearby...
-
Page 14: Controls And Features
FILL THE TANK WnTH 3. Turn the relief-release valve FIG. 11, page 12) to the open position_ Solution pumped through the suction tubing, head, then returned to the tank (takes 3-5 minutes). 4. When you see solution returning through fill hole), close the relief-release CONTROLS AND FEATURES RELIEF-RELEASE VALVE -- The solution... - Page 15 KEEP YOUR DaSPENSUNG RESERVOIR (TANK) SOLUTION installing the solution dispensing the solution level in the tank daily. the Low Level Indicator when about solution remains. After awhile, you will know about how much solution it uses each day and how often to refill the tank.
- Page 16 I KEEPYOUR DUSPENSnNG LUBRICATION least lubricate the solution pump as follows: 1. Unplug the electrical power cord, 2. Loosen the set screw in the feed control and remove the knob and bushing, 3. Remove the pump top cover, 4. Clean all the grease from the moving parts and inspect for wear, damage or corrosion.
- Page 17 KEEP YOUR D SPENSING If the dispensing system is exposed replace the solution tubing every6 place the tubing yearly if the system indoors. CLEAN THE STRAINER-- Before with solution, remove strainer, threaded fitting from the end of the strainer, clean by forcing water backwards...
- Page 18 25---'- MODEL NO. 625.349290 RETURN...
-
Page 19: Parts List
PARTS LiST PART DESCRIPTION NUMBER 818405 Float Assembly 818399 Pipe, Low Level Indicator 818510 Tank Cap 8800650 Tank, 15 Gal. (incl. Cap, Key No. 3) U0812612 Bulkhead Fitting (2 req.) Tank Base 818382 811704 Nylon Nut (4 req.) 811703 Nylon Screw (4 req.) 8800418 Strainer... - Page 20 Sears salesperson or call your nearest information Sears, Roebuck and Co., Chicago, IL 60684 U.S.A. Solution Dispensing System, parts or service, simply contact and Co stores you call or visit Dispensing...