Stanley FATMAX FME650 Original Instructions Manual page 9

Hints for optimum use
● Always hold the tool securely. For precision work, hold the
tool near the front.
● Clamp the workpiece whenever possible, especially when
using cutting blades.
● Do not exert too much pressure on the tool.
● Always use the appropriate type of attachment for the
workpiece material and type of cut.
● Regularly check the condition of accessories. Replace
when necessary.
● Mark the desired starting point.
● Switch the tool on and slowly feed attachments into the
workpiece at the desired starting point.
● Clamp a piece of plywood or soft wood to the back of the
workpiece and saw through the combination in order to
obtain a clear cut.
● Do not force the cutting blade into the workpiece. Note
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
● When cutting metal spread a thin film of oil along the
cutting line before cutting.
● When sanding new layers of paint before applying another
layer, use extra fine grit.
● On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
● Consult your retailer for more information on
available accessories.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
Warning! Before performing any maintenance
on the tool, unplug the tool. Unplug the charger
before cleaning it.
● Regularly clean the ventilation slots in your toolusing a
soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
(original instructions)
Technical data
Voltage V
AC
No-load speed min
-1
Oscillating angle Degrees
Power W
Weight
kg
Level of sound pressure according to EN62841:
Sound pressure (L ) 94.2 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 105.2 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN62841:
Cutting wood (a ) 7.9 m/s , uncertainty (K) 1.5 m/s
2
h, CW
Cutting metal (a ) 7.9 m/s , uncertainty (K) 1.5 m/s
2
h, CM
Sanding (a ) 8.2 m/s , uncertainty (K) 1.5 m/s
2
h
EC declaration of conformity
%
MACHINERY DIRECTIVE
FME650 oscillating tool
STANLEY FATMAX declares that these products described
under "technical data" are in compliance with:
EN62841-1:2015 , EN62841-2-4:2014.
These products also comply with Directive 2006/42/EC,
2014/30/EU and 2011/65/EU. For more information, please
contact STANLEY FATMAX at the following address or refer to
the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
STANLEY FATMAX .
STANLEY FATMAX Europe, Egide Walschaertsstraat14-18,
Guarantee
English
FME650 (Type 1)
230
10,000-22,000
1.4 - 2.8
300
1.53
2
2
2
A. P. Smith
Technical Director of Engineering
2800 Mechelen, Belgium
30/04/2019
9