Watching Recorded Programmes ......28 Table of Contents Timeshift Recording ..........28 Disk Format ............29 Safety Information ..........2 Schedule List ............29 Markings on the Product........2 CEC ...............29 Introduction ............4 Features ..............4 Google Cast............30 HBBTV System............30 OLED TV Operations ..........4 Quick Standby Search ...........31 Stand Installation &...
• Do not expose the TV to direct sunlight or do Safety Information not place open flames such as lit candles on the top of or near the TV. • Do not place any heat sources such as electric CAUTION heaters, radiators, etc.
Page 4
WARNING WALL MOUNTING WARNINGS Do not ingest the battery, Chemical Burn Hazard This product or the accessories supplied with the • Read the instructions before mounting your TV product may contain a coin/button cell battery. If the on the wall. coin/button cell battery is swallowed, it can cause •...
intended to achieve, showing the hidden areas of Introduction dark shadows and sunlight with full clarity, colour and detail. HDR/HLG content is supported via native Thank you for choosing our product. You’ll soon be and market applications, HDMI, USB inputs and enjoying your new TV.
Page 6
• It will take about 6 minutes. In order not to interrupt • It will take about 15 minutes. In order not to interrupt the operation it is recommended to wait until the the operation it is recommended to wait until the operation is completed.
Stand Installation & Antenna Connection Wall Mounting Connect the aerial or cable TV plug to the AERIAL INPUT (ANT) socket located on the left side of the TV Assembling / Removing the pedestal or satellite plug to the SATELLITE INPUT (LNB) socket Preparations located on the rear side of the TV.
Other Connections If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them. When using the wall mounting kit Connector Type...
The joystick allows you to control the Volume / Turning On/Off the TV Programme / Source and Quick Standby-On functions of the TV. Connect power Note: The position of the joystick may differ depending on IMPORTANT: The TV set is designed to operate on the model.
Remote Control Standby: Quick Standby / Standby / On Numeric buttons: Switches the channel in Live TV mode, enters a number or a letter in the text box on the screen Language: Switches among sound modes (analogue TV), displays and changes audio language (digital TV, where available) Volume +/- Microphone: Activates the microphone on the remote...
network and press OK if you want to use wireless Initial Setup Wizard connection instead of wired connection. 6. Network Connection Note: Follow the on-screen instructions to complete the initial setup process. Use the directional buttons and the OK button You will be directed to the next step automatically, if on the remote to select, set, confirm and proceed.
Page 12
OK on the remote to confirm and proceed. You can environment. This option is intended only for store also view Terms of Service, Privacy Policy and use. It is recommended to select Home for home use. Play Terms of Service on this screen. To display the 13.
Satellite LNB Configurations: Set the parameters for LNB. For DiSEqC antenna type select the correct DiSEqC If Satellite option is selected, Antenna Type screen port corresponding to your satellite system. Set other will be displayed next. If you have a Direct satellite parameters in accordance with your satellite system system, you can proceed to the next step quickly by if necessary.
device. Press the Home button to display Home rows for favourite apps, recent Live TV programmes Screen. You can also select the Android TV Home and recommendations from streaming apps. In the option from the Inputs menu to switch to Home Discover tab recommendations from streaming Screen.
Page 15
or on the TV to turn the screen on again. Note that Do Not Track: Set your preference regarding the you can not turn the screen on via the Volume +/-, tracking behaviour for HBBTV services. Mute and Standby buttons. These buttons will Cookie Settings: Set your cookie setting function normally.
System Information: Display detailed system Other options information on the current channel such as Signal Add new network: Add networks with hidden SSID’s. Level, Signal Quality, Frequency, etc. Scanning always available: You can let the location Record service and other apps scan for networks, even when WLAN function is turned off.
Page 17
Channel Skip: Set channels to be skipped when or the Right directional button to start scan. The found switching the channels via Programme +/- buttons channels will be stored in the channel list. on the remote. Highlight the desired channel/s on the LCN: Set your preference for LCN.
Satellite Re-scan: Start a satellite scan beginning first selected channel. You can press the Yellow button with the antenna selection screen. When this scanning and enter the number of the channel you want to select. option is preferred, some scanning configurations will Then highlight OK and press OK to go to that channel.
turn them on/off, turn on/off the notifications, clear the Parental Controls data and cache, etc. Highlight an app and press OK (*) To enter this menu PIN should be entered first. Use the PIN to see available options. that you have defined during the initial setup process. If you have Changing the storage location of an app changed the PIN after the initial setup use that PIN.
Page 20
Auto Sleep: Define an idle time after which you initial setup. If you didn’t set a PIN during the initial setup, you can use the default PIN. The default PIN is 1234. want your TV to enter sleep mode automatically. 4 Hours, 6 Hours and 8 Hours options are available.
Page 21
MPEG NR: MPEG Noise Reduction cleans up signal type as it is. It can be usable especially for block noise around outlines and noise on the back- RGB inputs. Turn the PC Mode function on or off. ground. Set your MPEG NR preference as Low, De-Contour: Decreases the contour effects in Medium, Strong or turn it off by setting as Off.
Page 22
OLED: Displays OLED settings. Digital Output: Set the digital sound output prefer- ence. Auto, Bypass, PCM, Dolby Digital Plus and OLED Compensation: You can perform this pan- Dolby Digital options will be available. Highlight the el maintenance operation manually to protect the option you prefer and press OK to set.
Page 23
enhancement. Off, Low, Medium and High options instructions and read the information displayed on will be available. Set according your preference. the screen before proceeding. Note: This feature has an effect only if the input audio Note: Formatting the connected storage device will erase format is AC-4 or dolby audio processing is enabled.
Energy Saver: Define a time after which you want Text to speech: With text-to-speech feature, your your TV to turn itself off for energy saving. Set as TV can convert written text into voice text to help Never to disable. visually impaired people listen to the information they are unable to read.
press the OK button. Virtual keyboard will be displayed. favourite list press the Yellow button, then highlight Enter all or a portion of the name or number of the the Delete option and press OK. channel you want to find, highlight the check mark Programme Guide symbol on the keyboard and press OK.
Page 26
Internet menu. You can also highlight the Connected/ connect. For more information refer to Network & Not Connected icon on the Home screen and press OK Internet section under the title of Settings. to access this menu. For further information refer to Network &...
protocol in order to avoid any possible problems while photo and text files a preview of the highlighted file watching videos. will be displayed in a small window on the left side of the screen if the browse mode is set to List View. You You must change your modem’s SSID when there are can also use Programme +/- buttons to jump directly any other modems around with the same SSID.
slide show will stop after the last listed file is displayed Rotate: Rotate the image. The image will be rotated and media player screen will be displayed. 90 degrees clockwise each time you press OK. You can also press the Green button to rotate. This option Info: Display the info bar.
It uses function could lead to copyright infringement of the Multi Media Player application. The media content authors' rights. Toshiba asks you to respect the types have different priorities in order to be played. The intellectual property rights of third parties.
mode. In Manual mode, if you prefer, you can format Devices must support HDMI CEC and must be your USB storage device and specify the storage space connected with an HDMI connection. that will be used for timeshift function. When the setup In order to make use of the CEC functionality the is complete, the Disk Setup Result will be displayed.
if eARC is disabled from the sound menu, then TV tap on it. Available devices will be detected and listed. initiates ARC. Select your TV from the list and tap on it to start casting. In order to activate ARC feature the eARC option To cast an app to the TV screen…...
If you do not notice the flickering, the batteries may Quick Standby Search be exhausted. Replace the batteries. If the remote is still not working, the remote control might be broken If earlier an automatic search is performed, your TV will and needs to be checked.
HDMI Signal Compatibility Source Supported Signals 480i 60Hz 480p 60Hz 576i, 576p 50Hz 720p 50Hz,60Hz 1080i 50Hz,60Hz 24Hz, 25Hz, 30Hz, 1080p 50Hz, 60Hz HDMI 24Hz, 25Hz, 30Hz, 3840x2160p 50Hz, 60Hz 24Hz, 25Hz, 30Hz, 4096x2160p 50Hz, 60Hz In some cases a signal on the TV may not be displayed properly.
Supported DVI Resolutions When connecting devices to your TV’s connectors by using a DVI converter cable (DVI to HDMI cable - not supplied), you can refer to the following resolution information. 56Hz 60Hz 66Hz 70Hz 72Hz 75Hz 640x480 800x600 1024x768 1280x768 1280x960 1360x768...
content. Revocation should not affect unprotected Licences content or content protected by other content access technologies. Content owners may require you to The terms HDMI, HDMI High-Definition Multimedia upgrade PlayReady to access their content. If you Interface, HDMI trade dress and the HDMI Logos are decline an upgrade, you will not be able to access trademarks or registered trademarks of HDMI Licens- content that requires the upgrade.
Disposal Information The following information is only for EU-member states: Disposal of products The crossed out wheeIed dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres.
Restriction of Chemicals), entered into force on 1 June 2007. Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation.