Advertisement
EZ Connect™ 802.11g 108Mbps
EZ Connect™ 802.11g 108Mbps
EZ Connect™ 802.11g 108Mbps
Wireless to Ethernet Bridge
Wireless to Ethernet Bridge
Wireless to Ethernet Bridge
™ 802.11g 108Mbps
Ethernet Bridge
Access the Web-Based Configuration
1. Configure your Ethernet adapter, which has been connected by wire to the SMCWEBT-G
device for a static IP-address in the 192.168.2.xxx range, where xxx should be between 1.254.
Please do not use the 192.168.2.25 address. Please refer the user manual for further
information about IP-addressing and settings.
2. As subnet mask, enter 255.255.255.0 during the IP-configuration if not selected
automatically.
3. Open up your web browser and enter http://192.168.2.25/
4. This will redirect you to the web configuration of the SMCWEBT-G. Please enter the
administrator password, which is by default: "smcadmin" to access the html pages for
further steps.
Note: If you have already set your Ethernet adapter for this IP address, you can avoid
entering the IP address as URL in your web browser by clicking the Access the
Web-based Configuration link. It will automatically start your default browser and
load the login page of the SMCWEBT-G
Hardware Installation
Hardware Installation
Hardware Installation
1. Select the Site - Choose a location for your SMCWEBT-G unit. Usually, the best location is at
the center of your wireless coverage area, if possible within line-of-sight of all wireless
devices.
2. Place the unit in a position that gives it maximum coverage: Normally, the higher you place
the antenna, the better the performance.
3. Position the antennas as desired. For more effective coverage, position the antennas along
different axes. For example, try positioning the antennas around 45 to 90 degrees apart.
(The antennas emit signals along the toroidal plane - and thus provide more effective
coverage when positioned along different axes.)
SMCWEBT-G
4. If used in Wireless Bridge mode, use an Ethernet cable from the host device to the
SMCWEBT-G. Connect the provided Ethernet cable to the RJ-45 socket of the host device
that you want to connect to your wireless network.
5. If used in Access Point / Repeater mode, the SMCWEBT-G can be wired to an Ethernet
network through an Ethernet device such as a hub or a switch using category 3, 4, or 5 UTP
Ethernet cable and an RJ-45 connector. For the configuration you may need to connect the
unit directly to your PC's Ethernet adapter directly.
6. Connect the power cable - Connect the power adapter cable to the 5 VDC power socket on
the rear panel.
7. Warning: Use only the power adapter supplied with the SMCWEBT-G.
Configuration
8. Check the LED's on the front of the unit to make sure the adapter is turned on properly and
the status is okay.
The installation method makes the process as simple and Plug-and-Play as possible. Please be
sure that you have successfully completed the steps shown in the previous section before
SMCWEBT-G
SMCWEBT-G
SMCWEBT-G
proceeding.
Run the EZ Configuration Wizard
1. Please make sure, your Ethernet adapter is configured correctly. For further information
please refer to the manual or the steps 1 and 2 in the "Access the Web-Based Configuration"
section above.
2. Click on the Run EZ Configuration Wizard button
3. Select the operational mode for your SMCWEBT-G device. (Access Point / Repeater /
Wireless to Ethernet Bridge) and click Next.
4. Enter the SSID and select the used wireless channel for AP / Repeater mode or only the
preferred SSID for Wireless to Ethernet Bridge mode. In the second case the channel will be
selected automatically. Click Next.
5. Select the Encryption method and enter the necessary keys in the fields to enable wireless
security for your SMCWEBT-G. Click Finish to save and apply settings.
6. The device will reboot and load the new configuration immediately.
Configuration
Configuration
Configuration
1. Insert the Installation CD-ROM, wait until the welcome screen appears automatically. If it
doesn't, open up the My Computer folder, select your CD-ROM drive, and double-click on its
icon.
2. Select from following options (shown on the screen) to configure your SMCWEBT-G
a. Access the Web-Based configuration
b. Run the EZ Configuration Wizard
Hardware Installation
EZ Connect™ 802.11g 108Mbps
Wireless to Ethernet Bridge
Configuration
From U.S.A. and Canada
If you are looking for further contact
(24 hours a day, 7 days a week)
information, please visit
(800) SMC-4-YOU; Phn: (949) 679-8000;
www.smc.com
Fax: (949) 679-1481
From Europe : Contact details can be found
38 Tesla
on www.smc.com
Irvine, CA 92618
Phone: (949) 679-8000
INTERNET
E-mail addresses:
techsupport@smc.com
Model Number: SMCWEBT-G
Driver updates:
http://www.smc.com/index.cfm?action=tech
support drivers downloads
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no
responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third
parties, which may result from its use. No license is granted by implication or otherwise under any patent
or patent rights of SMC. SMC reserves the right to change specifications at any time without notice.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
Copyright © SMC Networks, Inc., 2003. All rights reserved.
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc.
Other product and company names are trademarks or registered trademarks of their respective holders.
EZ Conn
SMCWEB
Wireless
Advertisement
