Toshiba Satellite P75-A User Manual
Toshiba Satellite P75-A User Manual

Toshiba Satellite P75-A User Manual

Hide thumbs Also See for Satellite P75-A:
Table of Contents

Advertisement

Quick Links

User's Manual
Satellite P70-A/P75-A/P70t-A/
P75t-A
Qosmio X70-A/X75-A
series

Advertisement

Table of Contents
loading

Summary of Contents for Toshiba Satellite P75-A

  • Page 1 User's Manual Satellite P70-A/P75-A/P70t-A/ P75t-A Qosmio X70-A/X75-A series...
  • Page 2: Table Of Contents

    Using the Touch Pad ................4-2 The Keyboard ..................4-3 Remote Controller ................. 4-6 Optical disc drives ................4-11 TOSHIBA VIDEO PLAYER ..............4-18 TOSHIBA Blu-ray Disc Player ............4-20 3D Playback on an External 3D Device ..........4-22 TV Tuner ....................4-27 User's Manual...
  • Page 3 TOSHIBA System Settings ..............5-10 USB Charge ..................5-11 Sleep and Music .................. 5-14 TOSHIBA Media Player by sMedio TrueLink+ ........5-15 Using CyberLink MediaShow 6 for TOSHIBA ........5-16 TOSHIBA PC Health Monitor .............. 5-18 AirGet for TOSHIBA ................5-19 Using the Hard Disk Drive (HDD) Protection ........
  • Page 4: Chapter 1 Toshiba Legal, Regulatory And Safety

    TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
  • Page 5: Regulatory Information

    ® The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
  • Page 6 Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s External RGB monitor port, Universal Serial Bus (USB...
  • Page 7 EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected/implemented those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards.
  • Page 8 Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
  • Page 9 The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. TOSHIBA will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation.
  • Page 10: Video Standard Notice

    For more detailed information about recycling of this product, please visit our website (http://www.toshiba- india.com) or contact call center (1800-200-8674). These symbols may not stick depending on the country and region where you purchased.
  • Page 11 ------------------------ /*===================================================== Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 12 ---------------------------------- /* Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to.
  • Page 13: Energy Star Program

    ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer...
  • Page 14: Disposing Of The Computer And The Computer's Batteries

    Disposing of the computer and the computer's batteries Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government. This computer contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them.
  • Page 15: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
  • Page 16 Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat. To keep your computer in prime operating condition, protect your work area from: Dust, moisture, and direct sunlight. Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
  • Page 17 Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely - in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.
  • Page 18: Safety Icons

    Instruction Manual for Safety and Comfort All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer. Safety Icons Safety icons are used in this manual to bring important information to your attention.
  • Page 19: Chapter 2 Getting Started

    Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
  • Page 20: Short Name

    Click Tap the Touch Pad or click the left Touch Pad control button once. Left click the mouse once. Tap the touch screen once (only for touch screen models). Right-click Click the right Touch Pad control button once. Right click the mouse once. Press and hold on the touch screen (only for touch screen models).
  • Page 21: Using Your Computer For The First Time

    DC power and reduces the voltage supplied to this computer. Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.
  • Page 22 Never plug the AC adaptor into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury. Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use.
  • Page 23 Figure 2-3 Connecting the power cord to the AC adaptor (3-pin plug for X70-A) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on your computer.
  • Page 24 Figure 2-6 Opening the display panel 1. Display panel Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Be careful not to open the display panel too far as this could put stress on the display panel’s hinges and cause damage.
  • Page 25 After you turn on the power for the first time, do not turn it off until you have set up the operating system. Volume cannot be adjusted during Windows Setup. Open the display panel. Press the computer's power button. Figure 2-8 Turning on the power 1.
  • Page 26: Turning Off The Power

    Charms Use the Windows Charms to start apps, find documents, set up system components, and perform most other computing tasks. By pointing the mouse pointer to the upper or lower right corner of your screen, you will find a list of charms: Search, Share, Start, Devices and Settings.
  • Page 27 If you have entered data, either save it to the Hard Disk Drive or to other storage media. Make sure all disk/disc activity has stopped before removing the disk/ disc. If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk.
  • Page 28 Please note that keyboard keys can only be used if the Wake- up on Keyboard option is enabled within the TOSHIBA System Settings. If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.
  • Page 29 Close the display panel. Please note that this feature must be enabled within the Power Options. Press the power button. Please note that this feature must be enabled within the Power Options. When you turn the power back on, you can continue where you left off when you shut down the computer.
  • Page 30 Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature. Allows the use of the panel power off feature. Starting Hibernation Mode To enter Hibernation Mode, follow the steps below. Click the Settings charm.
  • Page 31: Chapter 3 The Grand Tour

    Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section.
  • Page 32: Left Side

    DC IN/Battery The DC IN/Battery indicator shows the condition indicator of the DC IN and the battery's charge - white(P70-A)/red(X70-A) indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor. Please refer to the Monitoring of power conditions section for more information on this...
  • Page 33 Figure 3-3 The left side of the computer (P70-A) Figure 3-4 The left side of the computer (X70-A) 1. Security lock slot 4. Universal Serial Bus (USB 3.0) port 2. TV tuner jack* 5. Universal Serial Bus (USB 3.0) port 3.
  • Page 34: Right Side

    Universal Serial Bus Two Universal Serial Bus ports, which comply to (USB 3.0) port the USB 3.0 standard, are provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.
  • Page 35 Figure 3-6 The right side of the computer (X70-A) 1. Headphone jack 5. HDMI out port 2. Microphone jack 6. External RGB monitor port 3. Universal Serial Bus (USB 3.0) port 7. Cooling vents 4. Universal Serial Bus (USB 3.0) port 8.
  • Page 36: Back

    HDMI out port HDMI out port can connect with Type A connector HDMI cable. External RGB monitor This port provides 15-pin, analog RGB port. port Please refer to the External RGB monitor port pin assignment section for information on external RGB monitor port pin assignment.
  • Page 37: Underside

    Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to the Battery section. Underside The following figures show the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
  • Page 38: Front With The Display Open

    Battery release latch Slide and hold this latch into its "Unlock" position in order to release the battery pack for removal.For more detailed information on removing the battery pack please refer to the Battery section. Memory module slot The memory module slot allows for the installation, replacement and removal of additional memory module.
  • Page 39 Figure 3-11 The front of the computer with the display panel open (P70-A) Figure 3-12 The front of the computer with the display panel open (P70-A touch models) User's Manual...
  • Page 40 Figure 3-13 The front of the computer with the display panel open (X70-A) 1. Wireless communication antennas 8. Keyboard (not shown)* 2. Microphone 9. Stereo speakers 3. Web Camera LED 10. Power button 4. Web Camera 11. Touch Pad 5. Microphone* 12.
  • Page 41 Do not point the web camera directly at the sun. Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty. Display screen 43.9cm (17.3") LCD screen, configured with the following resolutions:...
  • Page 42: Internal Hardware Components

    The processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Health Monitor utility by clicking Desktop -> Desktop Assist -> Support & Recovery -> PC Health Monitor, and then click PC Information.
  • Page 43 SSD is a large-capacity storage media which uses Solid-State Memory in place of a magnetic disk of the hard disk. Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors. Legal Footnote (Hard Disk Drive (HDD) Capacity) For more information regarding Hard Disk Drive (HDD) Capacity, please refer to the...
  • Page 44 Graphics Control ® Some NVIDIA graphics models may include NVIDIA Optimus™ technology feature. ® NVIDIA Optimus™ technology intelligently optimizes notebook performance by seamlessly switching between a discrete NVIDIA GPU for great graphics performance and an Intel integrated graphics chip for sustained battery life.
  • Page 45: Power Condition Descriptions

    This feature can be used if the computer is: running under battery mode using the internal LCD display only The Display Power Saving Technology feature is enabled as the factory default. If you want to disable this feature, you can disable it. ®...
  • Page 46 Power on Power off (no operation) AC adaptor Battery fully • Operates • No charge connected charged • No charge • LED: white (P70-A) • LED: white (P70-A) • LED: red (X70- • LED: red (X70-A) Battery partially • Operates •...
  • Page 47 pack's temperature falls to a normal range, charging will resume - this process will occur regardless of whether the computer's power is on or off. Power indicator Check the Power indicator to determine the power status of the computer - the following indicator conditions should be noted: White(P70-A)/ Indicates power is being supplied to the...
  • Page 48: Chapter 4 Operating Basics

    Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it. Using the Touch Screen Some models are equipped with a touch screen. You can use your finger to manipulate icons, buttons, menu items, the onscreen keyboard, and other items on the touch screen.
  • Page 49: Using The Touch Pad

    Swipe Quickly move your finger in from the edge of the screen, without pausing when you first touch it. Swipe from the left edge: shows your recently opened apps, and so on. Swipe from the right edge: opens or closes the charms (Search, Share, Start, Devices, Settings).
  • Page 50: The Keyboard

    Swipe Quickly move your finger in from the edge of the Touch Pad, without pausing when you first touch Swipe from the left edge: shows your recently opened apps. Swipe from the right edge: opens or closes the charms (Search, Share, Start, Devices, Settings). Swipe from the top edge: opens or closes the app command bar.
  • Page 51 CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. NUM LOCK When the NUM LOCK indicator glows, you can use the number keys on the keyboard for number entry. Function Key The function keys (F1 ~ F12) are the twelve keys at the top of your keyboard.
  • Page 52 Some functions will show the toast notification at the edges of the screen. Those toast notifications are disabled at factory default. You can enable them in the TOSHIBA Function Key application. To access it, click Desktop -> Desktop Assist -> Tools & Utilities ->...
  • Page 53: Remote Controller

    You can use your remote controller with a media player (such as ArcSoft TV5.0, TOSHIBA VIDEO PLAYER, TOSHIBA Blu-ray Disc Player, etc) to play discs and videos, or to watch and record television programs.
  • Page 54 Figure 4-2 Remote controller 1. Power 8. Red Button 14. Channel/Page 20. Pause Control 2. Start 9. Green Button 15. Arrows and OK 21. Stop 3. Teletext 10. Yellow Button 16. Mute 22. Volume Control 4. Recorded TV 11. Blue Button 17.
  • Page 55 Guide Allows you to switch to the Electronic Program Guide (EPG) screen if the ArcSoft TV 5.0 window is active. Live TV Allows you to switch to the Live TV screen if the ArcSoft TV 5.0 window is active. DVD Menu Opens the main menu on a DVD movie, if available.
  • Page 56 Volume Control Increases or decreases the volume while watching TV, viewing DVD's or replaying CD's. Play Plays the selected media. FWD (Fast Forward) Moves the media (video, disc, music, and so on) forwards. REW (Rewind) Moves the media (video, disc, music, and so on) backwards.
  • Page 57 When an obstacle stands between the infrared receiver window of your computer and the Remote Controller. When direct sunlight or strong fluorescent light strikes the infrared receiver window. When the infrared receiver window or the infrared emission part of the Remote Controller is dirty.
  • Page 58: Optical Disc Drives

    Figure 4-4 Pulling the battery tray 1. Battery tray lock 2. Battery tray Remove the discharged battery from the battery tray and lay a new one in place. Be sure to place the battery with correct polarities. Push it forward until you hear a click. Figure 4-5 Replacing the battery Optical disc drives The computer may be installed with a DVD Super Multi drive, Blu-ray™...
  • Page 59 Blu-ray™ Writer drive In addition to the above formats, Blu-ray™ Writer drive supports BD-R, BD- R DL, BD-RE and BD-RE DL. Blu-ray™ Writer drive BDXL™ In addition to the above formats, Blu-ray™ Writer drive BDXL™ supports BD-R TL, BD-R QL and BD-RE TL. Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable.
  • Page 60 Lay the disc, label side up, in the disc tray. Figure 4-7 Inserting a disc 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray.
  • Page 61 When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. Push the center of the disc tray to close it.
  • Page 62 - this may cause you to either lose data or incur other damage to the drive or media. Disclaimer TOSHIBA does not assume responsibility for the following: Damage to any disc that may be caused by writing or rewriting with this product.
  • Page 63 Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YUDEN CO., Ltd.
  • Page 64 DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell, Ltd. (for 3x and 5x speed media) BD-R: Panasonic Corporation BD-R DL: Panasonic Corporation BD-RE: Panasonic Corporation...
  • Page 65: Toshiba Video Player

    Keep mobile phones and other wireless communication devices away from the computer. TOSHIBA VIDEO PLAYER Please be aware of the following limitations when you use the TOSHIBA VIDEO PLAYER: Notes on use This software can only be used on Windows 8.
  • Page 66 Do not lock the computer using the Windows logo ( ) + L keys when running the TOSHIBA VIDEO PLAYER. The TOSHIBA VIDEO PLAYER does not have a parental control function. In order to protect copyrights, the Windows Print Screen function is disabled when TOSHIBA VIDEO PLAYER is running.
  • Page 67: Toshiba Blu-Ray Disc Player

    TOSHIBA VIDEO PLAYER features and instructions are explained in details in TOSHIBA VIDEO PLAYER Manual. Use the following procedure to open TOSHIBA VIDEO PLAYER Manual. Press the F1 key when TOSHIBA VIDEO PLAYER is launched and click the Help button. TOSHIBA Blu-ray Disc Player Please be aware of the following limitations when you use TOSHIBA Blu- ray Disc Player.
  • Page 68 When you purchase Blu-ray™ Video, make sure it matches your drive, otherwise it will not play properly. To playback video on an external display or TV using TOSHIBA Blu- ray Disc Player, use output devices like external displays or TV that have HDCP supported HDMI port.
  • Page 69: 3D Playback On An External 3D Device

    TOSHIBA Blu-ray Disc Player Manual. Use the following procedure to open TOSHIBA Blu-ray Disc Player Manual. Press the F1 key when TOSHIBA Blu-ray Disc Player is launched and click the Help button. 3D Playback on an External 3D Device 3D playback on an external 3D device feature is only provided with some models.
  • Page 70 2D home video and other 2D contents you created, in 3D according to your personal preferences. The TOSHIBA VIDEO PLAYER is set by default in the 2D format. By pressing the 2Dto3D conversion function button, you decide to activate the 2Dto3D conversion function and therefore decide to watch your 2D content in 3D.
  • Page 71 The protection of intellectual property rights is essential for TOSHIBA. In this respect, TOSHIBA underlines that the Player should not be used in a manner infringing such rights. It is your...
  • Page 72 The picture generated by 2Dto3D conversion function is not the same as a picture produced for 3D playback use. The 2Dto3D conversion function simply uses TOSHIBA's original algorithm to apply pseudo 3D effect to the 2D content. The Player is set by default in the 2D format. By pressing the 2Dto3D...
  • Page 73 Depending on the system environment, the player may automatically switch into 2D if you perform any of the following operations during 3D playback. Furthermore, you may experience some time lag when the switching occurs. - Opening windows or pop-ups such as [Right-Click Menu], [Settings Window], [File Select] or [Error Message].
  • Page 74: Tv Tuner

    TV Tuner Use the ArcSoft TV 5.0 to watch TV programs or record them.The dimensions and shape of the TV Tuner jack vary for different regions. Some models are equipped with a TV tuner. When the ArcSoft TV 5.0 is going to be used, be sure that the computer is hooked up to an AC adaptor, and please use the AC power.
  • Page 75: Battery

    computer using AC power mode. The AC adaptor offers some protection against (but does not entirely prevent) possible electric shock caused by lightning. For complete protection, do not operate your computer during a thunderstorm. Save data, shutdown Windows and turn off the power. Connect the coaxial cable to the TV Tuner jack on your computer.
  • Page 76 The computer's RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed. Dispose of the battery as required by local ordinances or regulations.
  • Page 77 using the computer - if you make heavy use of external devices for example, the battery might scarcely charge at all during operation. Battery charging notice The battery may not begin charging immediately under the following conditions: The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all).
  • Page 78 With repeated discharges and recharges, the battery's capacity will gradually decrease. In view of this it will be noted that an often used, older battery will not operate for as long as a new battery even when both are fully charged. Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on:...
  • Page 79 At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed below. 1. Turn off the computer's power. 2. Disconnect the AC adaptor and turn on the computer's power - if it does not turn on then go to Step 4.
  • Page 80: Lan

    Save your work. Click Power in the Settings charm, and then click Shut down while holding down the SHIFT key - ensure that the Power indicator is off. Remove all cables and peripherals that are connected to the computer. Close the display panel and turn the computer upside down. Slide the battery lock into its unlock ( ) position.
  • Page 81 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). This section describes how to connect/disconnect to a LAN. Do not install or remove a memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
  • Page 82: Additional Memory Module

    When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer. Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions.
  • Page 83 Additional memory module is a precision electronic component that may be fatally damaged by static electricity. Since the human body can carry static electricity, it is important that you discharge yourself before touching or installing any additional memory modules. To discharge your body’s static electricity, simply touch any metal close to you with bare hands.
  • Page 84 Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 4-14 Seating the memory module 1.
  • Page 85 Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 4-15 Seating the memory module cover 1. Memory module cover 2. Screw Product appearance depends on the model you purchased. Install the battery pack - refer to Replacing the battery pack section, if...
  • Page 86: Memory Media

    Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.
  • Page 87 Please note that an adaptor is required to use miniSD/microSD Card. Please note that not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media will operate properly. The slot does not support Magic Gate functions.
  • Page 88 Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards. If you reformat a memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows.
  • Page 89 Inserting memory media The following instructions apply to all types of supported media devices. To insert memory media, follow the steps as detailed below: Turn the memory media so that the contacts (metal areas) face down. Insert the memory media into the memory media slot on the front of the computer.
  • Page 90: External Display

    Do not remove the memory media while the computer is in Sleep or Hibernation Mode. The computer could become unstable or data in the memory media could be lost. Do not remove only the miniSD/microSD Card while leaving the adaptor in the memory media slot. External Display Your computer video capabilities can be enhanced with additional displays.
  • Page 91 At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with suitable size with correct aspect ratio. The HDMI out port HDMI (High-Definition Multimedia Interface) port digitally transfers both video and audio data without reducing the quality.
  • Page 92 1. Click Desktop -> Desktop Assist -> Control Panel -> Hardware and Sound -> Sound. 2. In the Playback tab, select the playback device which you want to switch to. 3. To use the internal speakers on your computer, select Speakers. To use the television or the external monitor that you have connected to the computer, select a different playback device.
  • Page 93: Security Lock

    An external display with HDMI port and a digital adaptor featuring Intel WiDi. The adaptor is a device that connects to the external display via HDMI port and can receive Wi-Fi signals from your computer. Type "Intel WiDi" from the Start screen and click Intel(R) WiDi. Intel WiDi application will launch and you are ready to start the connection.
  • Page 94: Optional Toshiba Accessories

    You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: Memory Kit DDR3/DDR3L-1600/1866 memory modules can easily be installed in the computer.
  • Page 95 Click Desktop and right click on the Speakers icon on the Taskbar, and then select Playback devices from the sub menu. Select Speakers, and click Properties. On the Enhancements tab select the sound effects you would like, and click Apply. DTS Studio Sound DTS Studio Sound™...
  • Page 96: Chapter 5 Utilities And Advanced Usage

    Assist. Furthermore, some utilities can also be launched from Start screen and desktop shortcut. TOSHIBA Desktop TOSHIBA Desktop Assist is a graphical user Assist interface that provides access to specific tools and TOSHIBA utilities and applications that make the use and configuration of the computer easier.
  • Page 97 Using the Hard Disk Drive (HDD) Protection section for more details. TOSHIBA HDD TOSHIBA HDD Accelerator is a utility that can Accelerator improve hard drive access performance by using part of the main memory of the computer as a cache.
  • Page 98 To start this utility, click Desktop -> Desktop Assist -> Media & Entertainment -> TOSHIBA Blu-ray Disc Player. For details on how to use TOSHIBA Blu-ray Disc Player, see the help file. TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption.
  • Page 99 To start this utility, type CyberLink from the Start screen, and then click CyberLink MediaShow 6 for TOSHIBA from the list that appears. For details on how to use CyberLink MediaShow, see the help file by clicking ? button in the main window.
  • Page 100 TOSHIBA Service This application allows your computer to Station automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited...
  • Page 101: Special Features

    To access the setup files of the drivers/utilities, type Applications from the Start screen, and then click Applications and Drivers from the list that appears. TOSHIBA Media Player by sMedio TrueLink+ application is not included in the setup files above but can be downloaded from Windows Store. Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use.
  • Page 102 Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Intelligent power A microprocessor in the computer's intelligent power supply detects the battery's charge, supply automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor.
  • Page 103: Toshiba Password Utility

    TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password. User Password To start the utility, click the following items: Desktop ->...
  • Page 104 To end the BIOS Setup, press F10, and then press ENTER to accept the changes. The computer will restart. If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE.
  • Page 105: Toshiba System Settings

    To run TOSHIBA System Settings, click Desktop -> Desktop Assist -> Tools & Utilities -> System Settings. The TOSHIBA System Settings window contains a number of tabs to allow specific functions of the computer to be configured. In addition there are also three buttons: OK, Cancel and Apply.
  • Page 106: Usb Charge

    TOSHIBA System Settings window. Some options shown in grey are possible to confirm their status. TOSHIBA System Settings screen may have the following tabs: General—Allows you to view the current BIOS version or change certain settings back to their default values Sleep and Charge/Sleep and Music—Allows you to set advanced...
  • Page 107 To set USB Sleep and Charge feature, click Desktop -> Desktop Assist - > Tools & Utilities -> System Settings -> Sleep and Charge. Move the slider to enable or disable the Sleep and Charge function. The Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification.
  • Page 108 When USB device cannot be charged by Auto Mode, change to Alternate Mode. This function may not be able to be used with some connected external devices even if the appropriate mode is selected. In this situation, disable and stop using this function. Some external devices cannot use Auto Mode.
  • Page 109: Sleep And Music

    It is recommended that AC adaptor be connected to the computer while supplying USB bus power (DC5V, 1.5A). When your computer battery capacity is too low to continue, "System ON CDP Charge Mode" may not work. In those cases, connect the AC adaptor and reboot the computer.
  • Page 110: Toshiba Media Player By Smedio Truelink

    This setting is only available when the Function under Battery Mode is enabled. TOSHIBA Media Player by sMedio TrueLink+ Please be aware of the following limitations when you use the TOSHIBA Media Player by sMedio TrueLink+: Notes on use This software is a multimedia player which can be used to play back video, music and photo.
  • Page 111: Using Cyberlink Mediashow 6 For Toshiba

    Operating TOSHIBA Media Player by sMedio TrueLink+ The steps for playing a video file on a local library: Click My Local Library on the Start Page of TOSHIBA Media Player. Click a video file to playback. The steps for playing a music file on a local library: Click My Local Library on the Start Page of TOSHIBA Media Player.
  • Page 112 Insert a DVD-R, DVD+R, DVD-RW, DVD+RW, BD-R or BD-RE disc into the optical disc drive. Add your media files by dragging it to Media Tray. Click Create -> Movie Disc. Select DVD-Video, AVCHD or Blu-ray Disc from Step1: Choose disc format. Select a destination drive.
  • Page 113: Toshiba Pc Health Monitor

    An Internet connection is required for uploading and downloading. TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health and the system cooling, informing you of significant system conditions. This...
  • Page 114: Airget For Toshiba

    Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel. Doing so will automatically delete all collected information from the HDD/SSD.
  • Page 115 If you tap the upload/download button during video playback, the current video will restart playback from the beginning. Preparation Before using AirGet for TOSHIBA, you need to install AirGet for TOSHIBA in your mobile device and pair the device with your computer by the following steps: Make sure both computer and mobile device have internet connections.
  • Page 116: Using The Hard Disk Drive (Hdd) Protection

    Done to go to the main menu. You can also skip the Remote Wake up test by clicking Skip. Using AirGet for TOSHIBA AirGet for TOSHIBA enables you to access files stored in your computer from mobile device. If the computer and mobile device are connected to the same network (e.g.
  • Page 117 Move the slider to the right to show HDD Protection icon in the Taskbar. There are the following conditions for HDD Protection icon. Normal TOSHIBA HDD Protection is enabled. Protection TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position. TOSHIBA HDD Protection is disabled. User's Manual 5-22...
  • Page 118 Detection Level There are four sensitivity levels in which vibrations, impacts and their similar signs are detected can be set to OFF, 1, 2 and 3 in ascending order. Level 3 is recommended for better protection of the computer. However, when the computer is used in a mobile environment or in other unstable conditions, setting the detection level to 3 could result in frequent execution of HDD Protection, which will slow down Hard Disk Drive reading and writing.
  • Page 119: System Recovery

    System Recovery There is a hidden partition allocated on the Hard Disk Drive for the System Recovery Options in the event of a problem. You can also create recovery media and restore the system. The following items will be described in this section: Creating Recovery Media Restoring the pre-installed software from your created Recovery Media...
  • Page 120 Please note that some of the disc media may not be compatible with the optical disc drive connected to your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding. USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding.
  • Page 121 Recovery Media. However, if you have already created a "Recovery Media", you can use it to restore the recovery partition. If you have not created "Recovery Media", please contact TOSHIBA support for assistance. Restoring the pre-installed software from the...
  • Page 122 You can also perform the restoration through PC settings in the operating system: Click the Settings charm and click Change PC settings. Click General under PC settings. Scroll down to Remove everything and reinstall Windows and click Get started. Follow the on screen instructions to finish the recovery. User's Manual 5-27...
  • Page 123: Troubleshooting

    In reality many problems can be solved simply, but a few may require help from TOSHIBA Support - if you find you need to consult others, be prepared to describe the problem in as much detail as possible.
  • Page 124 Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
  • Page 125 Before using a peripheral device or application software that is not an authorized TOSHIBA part or product, make sure the device or software can be used with your computer. Use of incompatible devices may cause injury or may damage your computer.
  • Page 126: Hardware And System Checklist

    If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the DC IN/Battery indicator. If the indicator is glowing, the computer is connected to a live external power source.
  • Page 127 If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact TOSHIBA Support. AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN/Battery indicator.
  • Page 128 However, if you do not believe the battery is at the end of its operating life, you should speak to TOSHIBA Support. Battery doesn’t If you frequently recharge a partially charged...
  • Page 129 (remapping involves changing or reassigning the function of each key). If you are still unable to use the keyboard, you should contact TOSHIBA Support. Internal display panel Apparent computer's display panel problems may be related to the computer's setup and configuration.
  • Page 130 - if so remove it and try to start the Drive computer again. If this has no effect, check the Boot Priority Options setting within the TOSHIBA System Settings. Slow performance The files on the Hard Disk Drive may be...
  • Page 131 If you are still unable to resolve the problem, contact TOSHIBA Support. Pointing device If you are using a USB mouse, you should also refer to both the mouse section and the documentation supplied with your mouse.
  • Page 132 Control Panel -> Hardware and Sound -> sensitive enough. Mouse. If you are still unable to resolve the problem, contact TOSHIBA Support. USB mouse Problem Procedure On-screen pointer In this instance the system might be busy - Try...
  • Page 133 If you are still unable to resolve the problem, contact TOSHIBA Support. USB device In addition to the information in this section, please also refer to the documentation supplied with your USB device.
  • Page 134 Sleep and Charge Enable the Sleep and Charge function in the function. TOSHIBA System Settings. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons.
  • Page 135 Volume cannot be adjusted during Windows start up or shut down. If you are still unable to resolve the problem, contact TOSHIBA Support. External monitor Please also refer to Operating Basics, and to the documentation supplied with your monitor for further information.
  • Page 136 Display error occurs Check that the cable connecting the external monitor to the computer is firmly attached. If you are still unable to resolve the problem, contact TOSHIBA Support. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub.
  • Page 137: Toshiba Support

    TOSHIBA Support. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first.
  • Page 138 - they are your best resource for current information and support. TOSHIBA technical support If you are still unable to solve the problem and suspect that it is hardware related, visit TOSHIBA technical support website http://www.toshiba.co.jp/ worldwide/. User's Manual 6-16...
  • Page 139: Appendix Specifications

    Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. P70-A Approximately 418.4 (w) x 272.5 (d) x 28/33.7 (h) millimeters (not including parts that extend beyond the main body).
  • Page 140: Ac Power Cord And Connectors

    Power Requirements AC adaptor 100-240V AC 50 or 60 Hz (cycles per second) Computer 19V DC External RGB monitor port pin assignment Signal Name Description Red Video Signal Green Video Signal Blue Video Signal Reserved Reserved Ground Ground Ground Ground Power Supply Ground Reserved...
  • Page 141 the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.75 mm Current rating: Minimum 2.5 amperes Certification agencies China: U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 Australia: Japan: DENANHO...
  • Page 142: Information For Wireless Devices

    Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.11 Standard on Wireless LANs (Revision a/b/g/n or b/g/ n), as defined and approved by the Institute of Electrical and...
  • Page 143 Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Card from TOSHIBA. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
  • Page 144 TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Card Specifications...
  • Page 145 The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
  • Page 146 Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Europe France: Outdoor use Military Radiolocation limited to 10mW use.Refarming of the 2.4GHz band e.i.r.p. within the has been ongoing in recent years to band allow current relaxed regulation Full 2454-2483.5MHz implementation planned 2012. Italy: For private use, a general authorization is required if WAS/...
  • Page 147 Russian Limited e.i.r.p 100mW. Permitted to use Federation: only for indoor applications, closed industrial and warehouse areas, and on board aircraft. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight.
  • Page 148 check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS 210 of Industry Canada.
  • Page 149 If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations.
  • Page 150 2.4 : This equipment uses a frequency of 2.4GHz. DS : This equipment uses DS-SS modulation. OF : This equipment uses OFDM modulation. 4 : The interference range of this equipment is less than 40m. : This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5MHz.
  • Page 151: Legal Footnotes

    This equipment is approved to the radio standard by the countries/regions in the following table. If you use this equipment in the countries/regions which are not listed in the table blow, please contact TOSHIBA Support. As of March 2013 Austria...
  • Page 152 For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation. Contact TOSHIBA technical service and support, refer to TOSHIBA support section for more information.
  • Page 153 Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
  • Page 154: Glossary

    Graphics Processing Unit (GPU) Graphics processing unit (GPU) performance may vary depending on product model, design configuration, applications, power management settings and features utilized. GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode.
  • Page 155 Direct Current DDR: Double Data Rate DIMM: Dual Inline Memory Module DVD: Digital Versatile Disc DVD-R: Digital Versatile Disc-recordable DVD-RAM: Digital Versatile Disc-random Access Memory DVD-R DL: Digital Versatile Disc Recordable Dual Layer DVD-ROM: Digital Versatile Disc-read Only Memory DVD-RW: Digital Versatile Disc-rewritable DVD+R DL: Digital Versatile Disc Recordable Double Layer...
  • Page 156 RAM: Random Access Memory RGB: Red, Green, and Blue RFI: Radio Frequency Interference ROM: Read Only Memory RTC: Real Time Clock S/P DIF: Sony/philips Digital Interface Format Secure Digital SDHC: Secure Digital High Capacity SDRAM: Synchronous Dynamic Random Access Memory SSD: Solid State Drive TFT:...
  • Page 157: Index

    Index hinges 3-11 opening 2-5 screen 3-11 AC adaptor additional 4-47 Display controller 3-13 connecting 2-3 DC IN 19V jack 3-6 Documentation list 2-1 Dual Pointing Device ASCII characters 4-5 Touch Pad 6-9 DVD Super Multi drive using Battery writing extending life 4-31 monitoring capacity 4-30 real time clock 3-13, 4-28...
  • Page 158 6-5 inserting 4-42 Power 6-4 removing 4-42 Real Time Clock 6-7 Sound system 6-13 TOSHIBA support 6-15 Memory media slot 4-39 Touch Pad 6-9 USB device 6-11 Moving the computer 1-14 USB mouse 6-10 MultiMediaCard removing 4-42...
  • Page 159 2-9 System automatic 5-6 Sound system problems 6-13 TOSHIBA Desktop Assist 5-1 USB device problems 6-11 Video mode 4-48 Video RAM 3-13 Web Camera 3-10 Wireless communication 7-5 User's Manual Index-3...

Table of Contents