1. Manuals
  2. Brands
  3. Stanley Manuals
  4. Saw
  5. SCM701
  6. Manual

Stanley SCM701 Manual

Hide thumbs Also See for SCM701:
Table of Contents

Advertisement

Quick Links

Download this manual
www.stanleytools-la.com
SCM701

Advertisement

Table of Contents
loading

Related Manuals for Stanley SCM701

Summary of Contents for Stanley SCM701

  • Page 1 SCM701...
  • Page 2 1 17...
  • Page 7 11 36...

  • Page 8: Intended Use

    Use of an RCD reduces the risk of Intended use electric shock. Your STANLEY SCM701 sliding compound mitre saw has 3. Personal safety been designed for sawing wood, plastic and nonferrous metal a. Stay alert, watch what you are doing and use common only.

  • Page 9: Additional Safety Instructions For Mitre Saws

    (Original instructions) ENGLISH h. Do not let familiarity gained from frequent use of tools Shorting the battery terminals together may cause burns allow you to become complacent and ignore tool or a fire. safety principles. A careless action can cause severe d.

  • Page 10: Safety Instructions For Mitre Saws

    Do not use the saw Repairs to the cut line guidance system should be carried to cut other materials than those recommended by the out by authorised repair agents or STANLEY service staff. manufacturer. Remove the battery from the machine before carrying out Do not take hold of the saw blade after working before it any maintenance or when changing the blade.

  • Page 11: Safety Of Others

    (Original instructions) ENGLISH parts. set correctly to support the workpiece and will not Use clamps to support the workpiece whenever interfere with the blade or the guarding system. With- possible. If supporting the workpiece by hand, you out turning the tool “ON” and with no workpiece on the must always keep your hand at least 100 mm from table, move the saw blade through a complete simulated either side of the saw blade.

  • Page 12: Additional Safety Instructions For Batteries And Chargers

    Use specifically designed noise-reduction saw blades. Chargers Labels on tool Use your STANLEY charger only to charge the battery in The following pictograms along with the date code are shown the tool with which it was supplied. Other batteries could on the tool: burst, causing personal injury and damage.
  • Page 13 If the supply cord is damaged, it must be replaced by the Lock down pin (Fig. F) manufacturer or an authorised STANLEY Service Centre Warning! The lock down pin should be used ONLY when in order to avoid a hazard.

  • Page 14: Removing The Blade

    ENGLISH (Original instructions) Changing or Installing a New Saw Blade (Fig. G, H, I) Charging: Warning! To reduce the risk of serious personal injury, turn Green LED Intermittent tool off and remove the battery pack before transporting, making any adjustments or removing/installing attachments or accessories.
  • Page 15 5 seconds, have the tool serviced by an authorised zero degree position. Set and lock the mitre arm at zero, hold STANLEY service centre. the wood firmly on the table and against the fence. With the Always be sure the blade has stopped before removing it from rail lock screw (18) tightened, turn on the saw by squeezing the kerf.

  • Page 16: Bevel Cuts

    Use the material clamp provided with your saw. To purchase a small fibres of wood still split out at the rear of the work piece, material clamp, contact your local retailer or STANLEY service stick a piece of masking tape on the wood where the cut will centre.
  • Page 17 (Original instructions) ENGLISH To install clamp (fig. P) The lower guard (4) on your saw has been designed to au- tomatically uncover the blade when the arm is brought down Insert the clamp (37) into the hole (19) behind the fence. and to cover the blade when the arm is raised.
  • Page 18 ENGLISH (Original instructions) Cutting base moulding up to 3.5" (90 mm) high angles. The chart below gives the proper angles for a variety vertically against the Fence of shapes. Position material as shown in Figure S. All cuts should be Examples made with the back of the moulding against the fence and with the bottom of the moulding against the table.

  • Page 19: Maintenance

    (Original instructions) ENGLISH they can easily shift slightly and very few rooms have exactly wood, as shown in figure V. Release the guard prior to starting square corners, all settings should be tested on scrap the motor. The guard mechanism will function properly during moulding.

  • Page 20: Protecting The Environment

    Further information is available at tion about our authorized service centers and if you need www.2helpU.com technical advice, repair, or genuine factory replacement parts, contact the STANLEY location nearest you or visit us at www. Technical data stanleytools-la.com. SCM701...
  • Page 21 (Original instructions) ENGLISH...
  • Page 22 ENGLISH (Original instructions)
  • Page 23 (Original instructions) ENGLISH...
  • Page 24 ENGLISH (Original instructions) Solamente para propósito de Colombia: Solamente para propósito de Argentina: Importado por: Black & Decker de Colombia S.A.S. Importa y Distribuye: Black & Decker Argentina S.A. Av. Cra 72 # 80-94, Oficina 902. Pacheco Trade Center Colectora de Ruta Panamericana Torre Titan Plaza Centro Comercial y Empresarial.

Table of Contents