Builder’s/standard programmable/non-programmable/ programmable thermostat, dual fuel, and thermidistat control (8 pages)
Summary of Contents for Bryant Legacy T2-NHP01-A
Page 1
T2- NHP01- A, T2- NAC01- A Legacyt Series Non- Programmable Thermostat Owner’s Manual...
Page 3
YOU WILL LOVE THIS THERMOSTAT. This Legacy non- programmable thermostat is an easy to use model that provides the most sought- after features for keeping your home comfortable. And with a slim profile, it is designed to be as smart – and smart- looking –...
Page 7
BUTTON IDENTIFICATION Selects whether the fan operates continuously (on) or only when needed for heating or cooling (auto) MODE Selects whether thermostat is set for heating, cooling, emergency heat (heat pump system only), auto (heat and cool as needed), or off Increases the temperature or adjusts the screen selection up when setting advanced features DOWN...
ON- SCREEN INDICATORS heat heat actual temp auto cool set at...
Page 9
ON- SCREEN INDICATORS 1. Fan mode – on or auto 2. System is in auxiliary (supplemental) mode 3. Current temperature 4. Thermostat mode is either off or using emergency heat 5. Fahrenheit 6. Keypad is locked (no padlock means unlocked) 7.
OPERATING THE THERMOSTAT Setting the temperatures for heating and cooling Your thermostat is installed with the heating set at 68 F and the cooling set at 72 F. You can use these or change them so your home is as warm or as cool as you would like it to be.
OPERATING THE THERMOSTAT Using the fan When the fan is on, it helps distribute air throughout your home for a more even temperature in all spaces. You can set the thermostat so that the fan runs only during your heating and cooling cycles (auto mode) or to run continuously. The thermostat is set at the factory to run automatically as needed.
OPERATING THE THERMOSTAT Using emergency heat (heat pump systems only) Emergency heat is useful when the automatic auxiliary heat system can’t keep up with demand. (Systems with heat pumps use “auxiliary heat” when it’s too cold outside for the heat pump to heat the house without help. The display indicator for this is aux heat on.) If the heat pump compressor that works with auxiliary heat fails, or if the heat pump isn’t working at all, you can turn on the emergency heat for that extra help.
OPERATING THE THERMOSTAT Installing or replacing the batteries You can install batteries in your thermostat so that if the power goes out, the display will still show the indoor temperature. In some situations, batteries are also the power source. Then, two AA batteries should last about one year.
Page 14
OPERATING THE THERMOSTAT 2. Press it down. This will disconnect the thermostat from the top of the wall plate. 3. Remove the thermostat from the wall bracket com- pletely by bringing it slightly toward you and lifting it up and off the lip on the lower edge of the wall bracket. 4.
Page 15
OPERATING THE THERMOSTAT 9. With the bottom of the thermostat attached to the bottom of the wall bracket, bring the thermostat back to the wall. Line up the latch at the top of the thermostat with the corresponding lip on the wall bracket. 10.
OPERATING THE THERMOSTAT Using the thermostat to turn the heating and cooling system off To use the thermostat to turn the heating and cooling system off, press the mode button on the left repeatedly until the display shows off in the upper left. Auto changeover The thermostat uses one of five modes: heat, cool, Em heat (heat pump version only), auto, and off.
ADVANCED OPTIONS Advanced options display codes chart You can customize a few features of your thermostat. This chart shows which features you can change and the codes associated with them. The codes will be shown on the display when you follow the instructions. Feature Configuration Change Indication...
ADVANCED OPTIONS Changing from Fahrenheit to Celsius Your thermostat is preset to display the temperature in degrees Fahrenheit. You can change this to Celsius. 1. Press and hold the mode button for about three seconds. The display will show U1 and the letter F in the center. 2.
ADVANCED OPTIONS Turning on the continuous backlighting The thermostat display lights up for a few seconds after you press any button. This is backlighting. It will go dark after a few seconds. If the thermostat is powered by electricity, it is possible to have a constant low level amount of backlighting until you press any button, which increases the lighting temporarily.
ADVANCED OPTIONS Keypad lockout The keypad lockout feature lets you “lock” the thermostat so nobody can change the temperature – or make any other changes – by pressing buttons. Keypad lockout is not activated when the thermostat is installed. Here’s how to activate it. 1.
ADVANCED OPTIONS Unlocking the keypad Here’s how to temporarily unlock the keypad. 1. Press and hold the up and down buttons on the right simultaneously for about five seconds. 2. The padlock icon will disappear. This means the keypad is unlocked and can be used.
Page 22
WHAT IF . . . The battery icon is displayed The battery icon appears on the display only when the battery starts to lose power. Replace it when one- third of the icon is black. If your thermostat is battery powered and you wait until the icon is just a silhouette with no black bars, you will slowly lose thermostat functions until it doesn’t work at all.
Page 23
WHAT IF . . . There is a power outage If you lose electricity and have batteries installed, the thermostat will continue to display the indoor temperature because it has a battery backup power source. This means that even though your heating and cooling system doesn’t work, you will still be able to monitor your home’s temperature.
Page 24
COMMON TERMS AND WHERE TO FIND THEM Auto changeover page 14 ......... . This feature automatically switches your system from heating to cooling –...
Page 28
Copyright 2017 Bryant Heating & Cooling Systems, 7310 W. Morris St. Indianapolis, IN 46231 Catalog No: OM- T2NHPA - 02 Replaces: OM- T2NHPA- 01 Edition Date: 04/17 Manufacturer reserves the right to change, at any time, specifications and designs without notice...