Table of Contents
Advertisement
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 10.
42a
42b
42d
42
Fig. 29
1. Turn the handle (45) to the closed position. Drive
out the pin (44). Remove the handle.
2. Remove the base (43).
3. Unscrew the drain valve (42). The gasket (42a)
and seat (42b) will stay in the valve.
Technical Data
Power Requirements
. . . . . . . . . . . . . . . . . . .
Generator
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Working Pressure Range
. . . . . . . . . . . . . . . . . . . . .
Motor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cycles/Gallon (liter)
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Delivery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tip Size
. . . . . . . . . . . . . . . . . . . . . . . .
with latex at 2000 psi (138 bar, 13.8 MPa)
Power Cord
. . . . . . . . .
14 AWG (1.5 mm
Inlet Paint Strainer
. . . . . . . . . . . . . . . .
Outlet Paint Strainer
. . . . . . . . . . . . . . .
Pump Inlet Size
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Outlet Size
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound Data:
Sound Pressure Level
. . . . . . . . . . . . . . . . . . . . . . .
Sound Power Level
. . . . . . . . . . . . . . . . . . . . . . . . .
*Measured while spraying with a .017 tip
Wetted Parts:
Displacement Pump
. . . . . . .
PTFE
, Aluminum, Polyethylene, Delrin , Leather
Filter
. . . . . . . . .
Aluminum, Steel,
NOTE:
PTFE
and Delrin are trademarks of the
Drain Valve
Apply thread sealant
Apply grease
to face of base
Torque into pump
manifold to 185 in–lb
42c
(21 N.m)
Handle shown
in closed position
43
44
45
02819
110 VAC, 50 Hz,
1 phase, 10A minimum
3000W minimum
0–3000 psi
(0 – 210 bar , 0–21 MPa )
3/4 hp
620 (164)
0.5 gpm (1.9 lpm)
one gun to 0.023 new tip
2)
, 3 wire, 6 ft (1.8 m)
12 mesh (1525 micron)
Stainless Steel Screen, reusable
60 mesh (250 micron)
1/2 npt(f)
1/4 npsm
79 dB(A)*
88 dB(A)*
Stainless steel, Carbon steel,
PTFE
, Stainless steel
Company.
Repair
1. Unscrew the spring retainer from the valve body.
Remove the spring, washers and stem/ball. Clean
any debris from the ball or seat area.
2. If replacing the gasket (42a) or seat (42b), pry out
the gasket.
NOTE: Whenever the gasket (42a) is removed, re-
place it with a new one.
3. Coat the o-ring (42d) with grease. Press the stem
into the valve body. Install the spring, washers and
spring retainer into the valve body.
4. Place the seat (42b) in the valve body so the
lapped side is toward the ball. Apply a small
amount of grease to the new gasket (42a) and
install it in the valve body.
NOTE: The gasket will protrude from the end of the
valve until the valve is tightened into pump, which
correctly seats the gasket.
Replacement
1. Apply a small amount of thread sealant (42e) onto
the valve (42) threads. Tighten the valve into the
pump manifold to 185 in–lb (21 N.m).
2. Lightly grease the face of the base (43) and install
the base. Turn the stem so the pin hole is vertical.
3. Securely install the handle (45) and drive pin (44).
Dimensions
Weight (dry w/o packaging)
Height
Length
Width
DANGER LABELS
The English language DANGER label shown on page
4 is also on your sprayer. If you have painters who do
not read English, order one of the following labels to
apply to your sprayer. The drawing below shows the
best placement of these labels for good visibility.
Order the labels directly from Graco, free of charge:
1–800–328–0211
French
185–956
Spanish
185–961
German
186–041
Greek
186–045
Korean
186–049
English
185–953
37 lb (17 kg)
19 in. (483 mm)
15 in. (381 mm)
14 in. (356 mm)
Apply other
language here
Advertisement
Table of Contents
