Table of Contents
Advertisement
Quick Links
Form No. 3367-431 Rev B
8, 11, and 14 Blade DPA Reel
Mower
Greensmaster
®
3000 Series
Model No. 04610—Serial No. 311000001 and Up
Model No. 04611—Serial No. 311000001 and Up
Model No. 04616—Serial No. 311000001 and Up
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)
Advertisement
Table of Contents
Related Manuals for Toro 04616
Summary of Contents for Toro 04616
- Page 1 Model No. 04610—Serial No. 311000001 and Up Model No. 04611—Serial No. 311000001 and Up Model No. 04616—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or Contents additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Introduction..............2 identifies the location of the model and serial numbers Safety ................ -
Page 3: Safety
Toro replacement parts and • Always wear substantial shoes. Do not operate accessories to keep the Toro all TORO. Never use cutting units while wearing sandals, tennis shoes, "will-fit" replacement parts and accessories sneakers or shorts. -
Page 4: Setup
Setup Media and Additional Parts Description Qty. Ball stud Mount to roller Operator’s Manual Read before installing and operating cutting unit Parts catalog Use to reference part numbers Certification of compliance Installing the Front Roller No Parts Required Procedure The cutting unit is shipped without a front roller. Install the roller using the loose parts supplied with the cutting unit and installation instructions included with the roller. -
Page 5: Using The Cutting Unit Prop
Using the Cutting Unit Prop No Parts Required Procedure Whenever the cutting unit has to be tipped to expose the bedknife/reel, prop up the rear of the cutting unit to make sure the nuts on the back end of the bedbar adjusting screws are not resting on the work surface (Figure 6). -
Page 6: Adjusting The Bedknife To The Reel
Figure 9 Figure 7 1. Snap ring 2. Drive coupler 1. Counter weight 5. Apply grease to the inside diameter of the drive coupler. Install the drive coupler to the left end of 2. On the right end of the cutting unit, remove the the cutting unit reel tube with a snap ring (Figure 9). -
Page 7: Adjusting The Rear Roller
(see the Toro Reel Sharpening Manual). Figure 10 Adjusting the Rear Roller 1. Bedbar adjusting screw No Parts Required 2. -
Page 8: Adjusting The Height Of Cut
2. To adjust rear roller proceed as follows: • Raise the rear of the cutting unit and place a block under the bedknife. • Remove the (2) nuts securing each roller bracket Adjusting the Height of Cut and spacer to each sideplate mounting flange. •... -
Page 9: Adjusting The Cut-Off Bar
3. Hook the screw head onto the cutting edge of the Recommended Bedknife/Height of Cut Chart (cont'd.) bedknife and rest the rear end of the bar onto the High-cut (Optional) 94-6392 .312-1.00 inch (7.9-25.4 rear of the roller (Figure 17). Fairway (Optional) 63-8600 .375-1.00 inch (9.5-25.4... -
Page 10: Product Overview
A selection of Toro approved attachments and accessories are available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. -
Page 11: Operation
Operation bedknife. If a file is occasionally run across the front edge to remove this burr, improved cutting can be obtained. Note: Determine the left and right sides of the After extended running, a ridge will eventually machine from the normal operating position. develop at both ends of the bedknife. -
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Servicing the Bedbar Removing the Bedbar 1. Turn bedbar adjuster screw, counterclockwise, to back bedknife away from reel (Figure 19). Figure 21 1. Bedbar bolt 3. -
Page 13: Backlapping The Reel
Note: Additional instructions and procedures on Backlapping are available in the Toro Sharpening Reel and Rotary Mowers Manual, Form No. 80-300PT. Note: For a better cutting edge, run a file across the front face of the bedknife when the lapping operation is completed. - Page 14 Notes:...
- Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.