Page 1
NOTE: This product may require approval of the relevant regulators and/or the sewerage system operator. Waste disposal must be installed according to AS/NZS 3500.2 requirements. This waste disposer is intended exclusively for home use. 220-240V AC, 50/60 Hz, 375 W OWNER’S MANUAL # QKGA016...
. to operate on 220-240 VAC, 50/60 Hz electrical circuits . 6 . When not operating a disposer, leave the drain cover (stopper) in place to reduce the risk of objects falling into the disposer . SAVE THESE INSTRUCTIONS QKGA016...
Warranty FIVE (5) YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported . We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation . ACM Pty Limited warrants this product to be free from defects in materials or workmanship for five (5) years from the date of purchase.
Flange ring Screw Ring tool Includes: NOTE: This waste disposer is intended to be plugged Supporting plate into a grounded receptacle that is controlled by a Top supporting ring (with 3 screws) dedicated switch (usually wall mounted) . Cushion mount QKGA016...
Installation REMOVAL OF OLD UNIT CAUTION: Risk of electric shock . Turn off electric power at fuse box or circuit breaker before removing old unit . General instructions - your model may vary . NOTE: CAUTION: Be sure to support the disposer when removing the mounting ring or it may fall .
(see Fig. 8b). Top supporting - Tighten the 3 top supporting ring screws sequentially until the Fig . 8b Fig . 8c ring screw flange is very securely fastened to the sink (see Fig. 8c) QKGA016...
Installation (continued) If at any time the bottom supporting ring becomes disengaged from the body of the waste disposer, then: Slot 1 . Align the slot in the bottom supporting ring with tab on the waste disposer body . 2 . Lower the bottom supporting ring and make the slot fit in the tab .
Insert a screw driver into the tool mount for added leverage, if Bottom needed (see Fig 13a) . supporting Tool ring Mount Tool Mount Fig.13 Fig.13a If you are unable to fully engage the bottom supporting ring, release and lower the waste disposer (see Fig 13b) . Fig. 13b QKGA016...
Installation (continued) Turn the bottom supporting ring 1/3 of a turn counter-clockwise Fig. 13c and repeat the mounting procedure described above (see Fig 13c) . - Connect the bottom of the elbow to the trap by tightening the slip nut (Fig . 14) . - Run water and check all connections for leaks .
. DO NOT BE ALARMED, the stainless steel turntables used will not corrode . SINGLE BOWL DOUBLE BOWL CENTER OUTLET approx 26 cm approx 26 cm 34 cm DOUBLE BOWL END OUTLET approx 26 cm QKGA016...
Troubleshooting Before seeking repair or replacement, we recommend that you review the following: Problem Solution The disposer is making loud noises . Other than the noises during grinding of small bones and fruit pits, these are usually caused by accidental entry of a spoon, bottle cap or other foreign objects .
Removable splash guard QHG114 Includes: Sink flange Rubber sink flange gasket QHG115 Flange ring Ring tool Includes: Supporting plate QHG117 Top supporting ring (with 3 screws) Cushion mount Bottom supporting ring QHG112 Includes: Elbow gasket Discharge elbow QHG106 Flange elbow Screw QKGA016...
Page 13
47 Stonedon Drive, East Tamaki, Auckland 2013 New Zealand www.acmptyltd.com Customer Service Hotline Telephone : 0800 744 794 - 8.00am – 4.30pm Made in China and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license by Conglom International Ltd. All Rights Reserved.