Table of Contents
Advertisement
Aeroquip by Danfoss FT1380P Crimp Machine Operator's Manual
Setup and Assembly Instructions
FT1380P-1-2
1. Secure the crimper base to a stable workbench using four 1'2 inch lag screws or other suitable fasteners.
2. Install the die cage hanger bracket on the back of the crimper base. (optional)
3. Place the pump on the bench to the right of the crimper and remove the plugs from the pressure port
and the return port.
4. Install the 2021-6-4S adapter into the pressure port in front and the 2021-6-6S adapter into the return port
on top.
5. Remove the SAE 37° plug from the free end of the GH793-4 hose.
6. Attach the GH793-4 hose to the 2021-6-4S adapter in the pump pressure port.
7. Install one end of the 2556-6 return hose onto the 2021-6-6S adapter in the pump return port.
8. Remove the SAE 37° cap on the 2021-4-6S adapter on top of the valve.
9. Install the free end of the 2556-6 return hose to the 2021-4-6S adapter on top of the valve.
10. Connect compressed air hose to the air inlet port (fittings are not provided for this).
11. Place the pump on the floor to the right of the crimper. If the hoses try to coil or kink, slightly loosen the
upper ends of the hoses, untwist them and retighten.
FT1380P-1-1
1. Secure the crimper base to a stable workbench using four 1'2 inch lag screws or other suitable fasteners.
2. Install the die cage hanger bracket on the back of the crimper base. (optional)
3. Place the pump on the bench to the right of the crimper and remove the plugs from the pressure port
and the return port.
4. Install the 2021-6-4S adapter into the pressure port in front and the 2021-6-6S adapter into the return port
in front.
5. Remove the SAE 37° plug from the free end of the GH793-4 hose.
6. Attach the GH793-4 hose to the 2021-6-4S adapter in the pump pressure port.
7. Install the straight fitting of the 2556-6 return hose onto the 2021-6-6S adapter in the pump return port.
8. Remove the SAE 37° cap on the 2021-4-6S adapter on top of the valve.
9. Install the 90° fitting of the 2556-6 return hose to the 2021-4-6S adapter on top of the valve. If the hoses
try to coil or kink, slightly loosen the upper ends of the hoses, untwist them and retighten.
FT1380P-1-3
1. Secure the crimper base to a stable workbench using four 1'2 inch lag screws or other suitable fasteners.
2. Install the die cage hanger bracket on the back of the crimper base. (optional)
3. Make sure that your pump has the requirements listed in Specifications section.
4. Place the pump on the bench to the right of the crimper and install a -4 SAE 37°adapter in the pressure
port.
5. Install a -6 SAE 37° adapter in the return port.
6. Attach the GH793-4 hose to the -4 SAE 37° adapter in the pump pressure port.
7. Remove the SAE 37° cap on the 2021-4-6S adapter on top of the valve.
8. Install a -6 return hose to pump return port and valve top port. This hose must be capable of containing
200 psi.
5 | Aeroquip by Danfoss FT1380P Crimp Machine Operator's Manual | 2023.06.
Hand Pump Kit & FT1380P-1-4 12Volt DC Kit
Air/Oil Pump Kit
Kit {No Pump)
AQ435955684211en-000101
Advertisement
Table of Contents
