Table of Contents
Advertisement
12
BALANCE setting mode. Then press the - or + buttons on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: This setting is saved permanently including after powering off
the RC-1572MKII.
To make temporary changes not saved after power off, from the remote
C
control press the BAL
button to access the BALANCE setting menu, then
E
press the up/down/left/right
Tone Control Bypass 8 C
Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. To turn on the tone control from
the front panel, press the MENU
then press the - or + buttons on the front panel to turn bypass on or off.
When tone bypass is set to on, the front display will show TONE BYPASS.
NOTE: This setting is saved permanently including after powering off
the RC-1572MKII.
To temporarily changes the Tone Control Bypass, press the BYPASS
on the remote control to toggle the Bypass mode enabled and disabled.
Bass and Treble Controls 8C
To set the Bass or Treble controls from the front panel , press the MENU
button to toggle to the Tone control menu and press the ENTER
to toggle to either the BASS or TREB Setting menu. Then press the - or +
button on the front panel to adjust the value. The Bass and Treble values
range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RC-1572MKII.
To temporarily change the Bass and Treble settings from the remote control,
C
press the BASS or TREB
button, then press the up/down/left/right
arrow buttons on the remote control to adjust the value.
NOTE: Bass and Treble changes are only available when Tone Bypass
is disabled (see Tone Control Bypass section).
A properly setup high-performance audio system produces the most natural
sound with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load
on the amplifier and speakers.
NOTE: Setting the Bass and Treble controls do not automatically turn
on the tone control. To turn on tone control, refer to previous section
Tone Control Bypass.
Source Input Selector 7 K
Press the corresponding input button on the front panel
K
to select the desired listening source.
Push the front panel source buttons to toggle between Optical 1 - 2 and
Coaxial 1- 2 or use the dedicated source button on the remote control.
arrow buttons to adjust.
button to toggle to the Bypass control
8
7
or remote control
Dimmer Control
Display Dimmer 8 B
To change the brightness of the front display, press the MENU
to toggle to the DIMMER Setting. Then press the - or + buttons on the front
panel to change the display brightness.
NOTE: This setting is saved permanently including after powering off
the RC-1572MKII.
To temporarily change the display brightness, press the DIM
the remote control.
POWER LED Dimmer 8
To change the brightness of the Power LED on the front panel, press the
8
MENU
button to toggle to the POWER LED Settings. Then press the - or
+ buttons on the front panel to change the LED brightness.
Valid settings include: BRIGHT, MID, DIM.
C
NOTE: This setting is saved permanently including after powering off
button
the RC-1572MKII.
Rotel Link 0
8
8
button
Rotel Link is not used for RC-1572MKII.
EXT REM IN Jack -
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when
the unit is installed in a cabinet and the front-panel sensor is blocked. Consult
E
your authorized Rotel dealer for information on these external repeaters and
the proper wiring of a jack to fit the mini-jack receptacle.
RS232 w
The RC-1572MKII can be controlled via RS232 for integration with
automation systems. The RS232 input accepts a standard straight DB-9
Male-to-Female cable.
For additional information on the connections, software, and operating codes
for RS232 control of the RC-1572MKII, contact your authorized Rotel dealer.
PC‑USB Input o
See Figure 5
Connect this input using the supplied USB cable to the PC-USB socket of
your computer.
The RC-1572MKII supports both USB Audio Class 1.0 and USB Audio Class
2.0 modes. Windows computers do not require installation of a driver for
USB Audio Class 1.0 and support playback of audio up to 96kHz sampling
rates. The Factory Default setting is USB Audio Class 1.0.
RC‑1572MKII Stereo Control Amplifier
8
button
B
button on
Advertisement
Table of Contents
