Advertisement
Quick Links
Quick Start
D
ESCRIPTION
This guide includes the following products:
Part Number
Description
1442821F1
SFP 3.125G BIDI 1310/1550 NM
1442821F2
SFP 3.125G BIDI 1550/1310 NM
The Small Form-Factor Pluggable (SFP) 3.125 Bidirectional
(BIDI) 10 km plugs into ADTRAN equipment designed to accept
SFPs. Installed into an appropriate host unit, the BIDI SFP
provides a 3.125G optical interface to the supporting system.
g
NOTE
The 1442821F1 and 1442821F2 must be deployed as pairs at
each end of the system. The 1442821F1 must be connected to
the 1442821F2 at the other end of the fiber.
I
NSTALLATION
To install the SFP into an appropriate module, complete the
following steps:
1. Inspect the SFP. If damaged, file a claim with the carrier and
then contact ADTRAN Customer Service.
2. Do not remove the protective end cap from the SFP until the
fiber optic cable is ready to be connected.
3. Insert the SFP into the SFP cage on the module. Ensure the
manufacturer's label on the SFP is facing upward for correct
installation.
4. Slide the SFP all the way into the receptacle until there is an
audible "click."
f
CAUTION!
Due to compliance certification requirements, use only SFPs
supplied by ADTRAN. ADTRAN cannot certify system integrity
with other SFPs.
w
NOTICE
The latch on the SFP is used to remove the SFP from the cage on
the circuit card.
Small Form-Factor Pluggable
SFP
3.125G BIDI 10 km
O
PERATIONAL
General
■
Module type: SFP
■
Fiber/Copper: Fiber
♦
SM/MM: Single Mode
♦
Single/Dual-fiber: Single Fiber
■
Optical Connector: LC
■
Applications: OC-48/STM-16; 1.0G, 3.125G
■
Distance: 10 km
■
Digital Diagnostic Monitoring: SFF- 8472 and SFF-8047i
Compliant
Optical
■
Optical Budget: 13 dB
■
Transmitter
♦
Laser Diode Type: DFB
♦
Tx Central Wavelength: 1310 nm
♦
Tx Output optical power: –5.0 dBm to +0.0 dBm
♦
Tx Spectral width: 1 nm
♦
SMSR: 30 dB
♦
Extinction Ratio: 8.2 dB
■
Receiver
♦
Rx Type: PIN
♦
Rx Central wavelength: 1550 nm
♦
Input optical power: +0 dBm to –18 dBm
♦
Receiver Overload: +0 dBm
♦
Receiver Sensitivity: –18 dBm
Environmental
■
Extended Support:
♦
Operational temperature range: –40°C to +70°C
♦
Case temperature hardened range: –40°C to +85°C
♦
Storage temperature range: –40°C to +85°C
♦
Relative humidity to 5 to 95%, noncondensing
February 2017
61442821F1-13A
S
PECIFICATIONS
Advertisement
Related Manuals for ADTRAN SFP Series
Summary of Contents for ADTRAN SFP Series
- Page 1 SM/MM: Single Mode The Small Form-Factor Pluggable (SFP) 3.125 Bidirectional ♦ Single/Dual-fiber: Single Fiber (BIDI) 10 km plugs into ADTRAN equipment designed to accept ■ Optical Connector: LC SFPs. Installed into an appropriate host unit, the BIDI SFP provides a 3.125G optical interface to the supporting system.
- Page 2 EMC Directive and Low Voltage Directive. Standards used to above standards, install only ADTRAN-approved Class 1 Laser demonstrate Compliance are EN 300 386 and EN 60950. Modules in ADTRAN products. For a list of ADTRAN-approved ♦ This device complies with Part 15 of the FCC rules.
- Page 3 1 ne nur ADTRAN zugelassene Klasse 1 Lasermodule in ADTRAN ADTRAN approuvés dans les produits d'ADTRAN. Pour une liste Produkte. Eine Liste der ADTRAN zugelassene SFPs und XFPs des SFP et XFP ADTRAN approuvés, voir http:/www.adtran.com/...
- Page 4 For inquiries, go to: http://adtran.com/training Warranty: ADTRAN will replace or repair this product within the warranty period if it does not ADTRAN CUSTOMER CARE: meet its published specifications or fails while in service. Warranty information can be From within the U.S.