Table Of Contents; Safety Considerations - Amana MVC96 BB Series Installation Instructions Manual

This device, which was assembled by Goodman Manufacturing
Company, L.P., contains a component that is classified as an intentional
radiator. This intentional radiator has been certified by the FCC: FCC ID
QOQBGM111. And this international radiator has an Industry Canada
ID: IC 5123A-BGM111.
This device complies with Part 15 of the FCC's Rules. Operation of this
device is subject to two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including
interference that may cause undesirable operation.
And this device meets the applicable Industry Canada technical
specifications.
The manufacturer of the intentional radiator (model no. BGM111) is
Silicon Laboratories Finland Oy, which can be contacted by calling 617-
951-0200. (www.silabs.com)
Goodman Manufacturing Company, L.P. may be contacted by calling
713-861-2500, or at 19001 Kermier Rd., Waller TX 77484.
(www.goodmanmfg.com)
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
This equipment complies with FCC radiation exposure limits. To ensure
compliance, human proximity to the antenna shall not be less then
20cm during normal operations.
Changes for modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.

TABLE OF CONTENTS

Safety Considerations ................................................. 2
Location Requirements & Considerations ............... 5
Combustion & Ventilation Air Requirements........... 8
Installation Positions .................................................. 8
Horizontal Applications & Considerations .............. 9
Vent/Pipe and Combustion Air .................................. 11
Special Instructions for Products Installed
in the State of Massachusetts ............................ 16
Condensate Drain Lines & Drain Trap ..................... 17
Gas Supply and Piping ................................................ 22
Propane Gas/High Altitude Installations............... 22
Duct Work .................................................................... 26
Electrical Connections ............................................. 29
Accessories .................................................................. 34
Startup Procedure & Adjustment ............................ 36
Normal Sequence of Operation ............................... 39
Safety Circuit Description ....................................... 40
Troubleshooting ......................................................... 40
Maintenance ................................................................. 41
Filters ............................................................................ 41
Before Leaving an Installation ................................ 42
Repair and Replacement Parts ................................. 42
Menu Options ................................................................ 43
Status Codes ................................................................ 44
Troubleshooting Chart ............................................. 45
Wiring Diagram ............................................................ 50
Start-Up Checklist ...................................................... 51

SAFETY CONSIDERATIONS

Adhere to the following warnings and cautions when
installing, adjusting, altering, servicing, or operating the
furnace. To ensure proper installation and operation,
thoroughly read this manual for specifics pertaining to the
installation and application of this product.
This furnace is manufactured for use with natural gas. It
may be field converted to operate on L.P. gas by using the
appropriate L.P. conversion kit listed in the PROPANE
GAS/HIGH ALTITUDE INSTALLATIONS section of this
manual
Install this furnace only in a location and position
as specified in LOCATION REQUIREMENTS &
CONSIDERATIONS section and INSTALLATION
POSITIONS section of this manual.
Provide adequate combustion and ventilation air to the
furnace as specified in COMBUSTION & VENTILATION
AIR REQUIREMENTS section of this manual.
Combustion products must be discharged to the outdoors.
Connect this furnace to an approved vent system only, as
specified in VENT/FLUE PIPE & COMBUSTION AIR PIPE
section of this manual.
Never test for gas leaks with an open flame. Use a
commercially available soap solution made specifically for
the detection of leaks to check all connections, as specified
in GAS SUPPLY AND PIPING section of this manual.
Always install a furnace to operate within the furnace's
intended temperature-rise range with a duct system which
has external static pressure within the allowable range, as
specified on the furnace rating plate and OPERATIONAL
CHECKS section of these instructions.
A gas-fired furnace for installation in a residential
garage must be installed as specified in the LOCATION
REQUIREMENTS AND CONSIDERATIONS section of
this manual.
2