Page 1
With Body Mass Index Features Owner’s Manual Cardinal Scale Mfg. Co. 8555-M260-O1 Rev J 203 E Daugherty, Webb City, MO 64870 USA Ph: 417-673-4631 • Fax: 417-673-2153 01/17 Printed in USA www.detecto.com Technical Support: Ph: 866-254-8261 • tech@cardet.com 8555-M260-O1 Rev J • 750EU Owner’s...
Date of Purchase ___________________ Before using this indicator, read this manual and pay special attention to all "WARNING" Purchased From ____________________ symbols: ___________________________________ ___________________________________ ___________________________________ IMPORTANT ELECTRICAL RETAIN THIS INFORMATION FOR FUTURE USE WARNING 8555-M260-O1 Rev J • 750EU Owner’s...
Page 4
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ATTENTION: RISQUE D'EXPLOSION SI LA BATTERIES EST REMPLACE'E PAR UN TYPE INCORRECT. REJETEZ LES BATTERIES UTILISE'ES SELON LES INSTRUCTIONS. 8555-M260-O1 Rev J • 750EU Owner’s...
INTRODUCTION Thank you for purchasing our Model 750EU Weight Indicator. It has been manufactured with quality and reliability and has been tested before leaving our factory to insure accuracy and dependability for years to come. This manual is provided to guide you through installation, operation and maintenance of your indicator.
EN 61000-3-2:2000 EN 61000-3-3:1995+A1 The Technical Construction File required by this Directive is maintained at the corporate headquarters of Cardinal Scale Manufacturing Company, 203 East Daugherty, Webb City, Missouri. _____________________ Mark Levels Quality Assurance Administrator 8555-M260-O1 Rev J • 750EU Owner’s...
Electrical Power The 750EU indicator has been designed to operate from a 110 to 240 VAC 50/60Hz 12 VDC 1A wall plug-in UL/CSA listed AC power adapter (Cardinal part number 6800-1045). Note that a special order is not required for operation at 240 VAC.
Spring Plunger Release Figure No. 3 Interconnections The load cell input and power connections are made at the bottom rear panel of the indicator. Refer to Figure No. 1 for the rear panel layout. 8555-M260-O1 Rev J • 750EU Owner’s...
INSTRUCTIONS. Battery Status The 750EU indicator will operate for up to 100 hours on fully charged Ni-Cad or NiMH batteries depending on the condition of the batteries (from new to about 500 recharges). The battery bar graph on the display indicates the battery capacity in 4 steps:...
If not, remove panel and check for one or more improperly positioned batteries. 11. Return the indicator to the scale mounting bracket. 12. The indicator is now ready for operation. Figure No. 5 8555-M260-O1 Rev J • 750EU Owner’s...
This key is used to reset the display to zero up to the selected limit of either 4% or 100% of scale capacity. The zero limit is set during setup and calibration of the indicator. 8555-M260-O1 Rev J • 750EU Owner’s...
The ZERO key can be used to clear the recorded values. Use the or keys to scroll through the 10 records. Press any other key to return the indicator to normal operation. NOTE! While reviewing the recorded weights, the display will alternate between the transaction number and the weight. 8555-M260-O1 Rev J • 750EU Owner’s...
This annunciator is turned on to indicate that the displayed weight is in pounds. This annunciator is turned on when the displayed height measurement is in centimeters. FEET INCHES These annunciators are turned on when the displayed height measurement is in feet and inches. 8555-M260-O1 Rev J • 750EU Owner’s...
NOTE! The BMI / ENTER key can be used to toggle between the calculated BMI value and the weight until the scale goes below 10% of capacity (40 lbs). At that point, a new height input is required. 8555-M260-O1 Rev J • 750EU Owner’s...
SETUP AND CALIBRATION Your Model 750EU indicator has been thoroughly tested and calibrated before being shipped to you. If you received the indicator with a scale, calibration is not necessary. If the indicator is being connected to a scale for the first time or recalibration is necessary for other reasons, proceed as indicated.
Page 16
Allowable values are: 0 = Minimal Filter 1 = Moderate Filter 2 = Heavy Filter 3 = Custom Filter NOTE! If 3 = Custom Filter is selected, two additional prompts will be displayed. 8555-M260-O1 Rev J • 750EU Owner’s...
Page 17
6. Starting at the left and preceding right, a series of dashes will appear on the display. The dashes will stay on the display momentarily, then disappear, after which the display will proceed to the next prompt. 8555-M260-O1 Rev J • 750EU Owner’s...
Page 18
Consult the factory Tech Support for the Acceleration of Gravity value for your location. NOTE! Once the Gravity Constant has been set, both CALGC= and oPGC= must be set to the same value to disable it. 8555-M260-O1 Rev J • 750EU Owner’s...
Page 19
BMI / ENTER key to save it and proceed to the next prompt. Allowable values are: 0 or 1. PUO=1 (YES) PUO=0 (NO) Weight display will be reset to weight display will not be reset to zero zero automatically on power up 8555-M260-O1 Rev J • 750EU Owner’s...
Page 20
Allowable values are 0 through 9 with 0 disabling Automatic Shutoff. Setup and Calibration Is Completed The setup and calibration process has been completed. The indicator will reset and then turn off. Remove power from the indicator and re-assemble for use. 8555-M260-O1 Rev J • 750EU Owner’s...
SETUP REVIEW The 750EU indicator allows several operational parameters to be reviewed and changed as necessary without having to enter the setup mode. To Enter Setup Review: 1. If indicator is on, press ON / OFF key. 2. Display will show oFF and indicator will turn off.
DO remove power before cleaning with a damp cloth. DO provide clean AC power and adequate protection against lightning damage. DO keep the surroundings clear to provide clean and adequate air circulation. 8555-M260-O1 Rev J • 750EU Owner’s...
EVENT COUNTER The Model 750EU Weight Indicator has been designed with an Event Counter type of security seal. When selected, the 750EU will display two 3-digit numbers representing the Calibration and Configuration counters. Calibration Counter The calibration counter is incremented when a value in the calibration part of setup is changed (USA, int, Unit, UnS, dPP, CAP, FLt, F, br, Sr, CAL, SetGC, CALGC, OPGC).
Page 30
(2) years from date of shipment. Detecto shall be the sole judge of what constitutes a defect.
Page 31
This warranty sets forth the extent of our liability for breach of any warranty or deficiency in connection with the sale or use of the product. Detecto will not be liable for consequential damages of any nature, including but not limited to, loss of profit, delays or expenses, whether based on tort or contract.