Detecto MedVue MVWIFI Installation, Configuration, And Operation Manual

Detecto MedVue MVWIFI Installation, Configuration, And Operation Manual

Wifi option

Advertisement

Quick Links

Model MVWIFI
WiFi Option
Installation, Configuration,
and Operation Manual
1
8555-M519-O1 Rev D • MedVue MVWIFI Operation

Advertisement

Table of Contents
loading

Summary of Contents for Detecto MedVue MVWIFI

  • Page 1 Model MVWIFI WiFi Option Installation, Configuration, and Operation Manual 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 2 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 3: Specifications

    NOTE: ## is the last 2  digits of the MAC address of the module. PRECAUTIONS Before using this device, read this manual and pay special attention to all NOTIFICATION symbols: ELECTRICAL STATIC IMPORTANT WARNING SENSITIVE 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 4: Fcc Compliance Statement

    Please do your part by making certain that this device is properly disposed of. The symbol shown to the right indicates that this device must not be disposed of in unsorted municipal waste programs. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 5: Installation

    4. Re-install the end cap and secure with the two (2) screws removed in step 1. 5. Press the ON/OFF key to turn the weight analyzer on. 6. The weight analyzer is now ready to configure for the network. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 6: Network Configuration

    4. You should then be presented with a new page which contains a form that can be used to set up the network configuration to either connect to an existing network, or act as a wireless access point. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 7 6. Press the ENTER key until the RESET ETHERNET prompt is displayed. 7. Change this setting to YES (press the 1/YES key) and then press the ENTER key. 8. Wait for the MedVue to reset the MVWIFI. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 8 The configuration web page in the MVWIFI module allows the module to be configured as either an access point, or to connect to an existing network. In order to accomplish this, a new parameter has been added on the web page “Network Mode”. MedVue 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 9 If this happens, it may be necessary to isolate the MVWIFI module from wireless signals and use the MVWIFI Reset to Defaults procedure to restore the network to a known configuration. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 10 The configuration web page in the MVWIFI module allows the module to be configured as either an access point, or to connect to an existing network. In order to accomplish this, a new parameter has been added on the web page “Network Mode”. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 11 If this happens, it may be necessary to isolate the MVWIFI module from wireless signals use the MVWIFI Reset to Defaults procedure to restore the network to a known configuration. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 12: Operation

    UU = units, upper case (LB, KG, TN, etc.) M = mode, upper case (G=gross, N=Net) SS = status, upper case (CZ=center-of-zero, MO=motion, BZ=gross weight below zero EE=entry - Input in progress, OC=over capacity) CR = carriage return (hex 0D) 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 13 Scale attempts to set the weight (represented as<xxxxxx.xxx> in the string) to the requested value. <LF>M<CR> Scale returns the current tare weight. <LF>U<CR> Scale will toggle between calibration units if conversion units have been set up in scale calibration. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 14 (see <LF>W<CR> above), Height, BMI, ID<CR> NOTE: If the MedVue weight analyzer has been set to continuous mode of outputting weight, it will output the weight in the format listed above for <LF>W<CR> every 500 milliseconds. 8555-M519-O1 Rev D • MedVue MVWIFI Operation...
  • Page 15: Statement Of Limited Warranty

    (2) years from date of shipment. Detecto shall be the sole judge of what constitutes a defect. During the first ninety (90) days Detecto may choose to replace the product at no charge to the buyer upon inspection of the returned item.
  • Page 16 Cardinal Scale Manufacturing Co. 102 E. Daugherty, Webb City, MO 64870 USA Ph: 417-673-4631 or 1-800-641-2008 Fax: 417-673-2153 Technical Support: 1-866-254-8261 Printed in USA E-mail: tech@cardet.com 8555-M519-O1 Rev D 08/19 8555-M519-O1 Rev D • MedVue MVWIFI Operation...

Table of Contents