Related Manuals for Costway HW68604
Summary of Contents for Costway HW68604
- Page 1 USER’S MANUAL 8 PIECE RATTAN SOFA SET HW68604 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
-
Page 2: Before You Start
Before You Start Read each step carefully before starting. It is very important to ensure each step followed in correct order, otherwise assembly difficulties may occur. Most of board parts are labeled or stamped on the raw edges. Have a check to make sure all parts are included. Work in a spacious area, preferably on a carpet close to where the unit will be used. - Page 3 Notice 50% Tighten before fixing all screws, Allen wrench is recommended instead of an electric drill. Place the item on a flat ground to adjust and make sure it remains stable. Tighten up all screws with tools gradually. If the screws are not aligned with holes during assembly, please loosen all the other screws to 50% and continue the assembly process.
-
Page 4: Part List
Part List 4 pcs 2 pcs 2 pcs 2 pcs 1 pc 1 pc 1 pc 1 pc 1 pc 1 pc 1 pc 2 pcs 1 pc 2 pcs 2 pcs 2 pcs 1 pc 1 pc 1 pc 1 pc 1 pc 2 pcs... -
Page 5: Hardware List
Hardware List Description Hardware Spec M6 x 60 mm Bolt M6 x 45 mm Bolt M6 x 35 mm 15 pcs Bolt M6 x 30 mm 4 6 pcs Bolt Bolt M6 x 25 mm Bolt M6 x 1 5 mm Plastic washers M6 x 8 mm 109 pcs... - Page 6 STEP 1 STEP 2 STEP 3 Finished...
- Page 7 STEP 4 STEP 5 STEP 6 STEP 7 Finished...
- Page 8 STEP 8 STEP 9 STEP 10 STEP 11 Finished...
- Page 9 STEP 12 STEP 13 STEP 14 Finished...
- Page 10 STEP 15 STEP 16 STEP 17 Finished...
- Page 11 STEP 18 STEP 19 STEP 20 STEP 21 Install part W1 then arrange all cushions inside storage Finished...
- Page 12 STEP 22 STEP 23 STEP 24 Finished...
-
Page 14: Care And Maintenance
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.Using solvents of any kind on your furniture may damage the finish. - Page 15 With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE! Mit Ihrer inspirierenden Bewertung wird COSTWAY konsistenter sein, um Ihnen EIN SCHÖNES EINKAUFSERLEBNIS, GUTE PRODUKTE und EFFIZIENTEN SERVICE zu bieten! Avec votre évaluation inspirante, COSTWAY continuera à...
- Page 16 DANGER WARNING FIRE OR EXPLOSION HAZARD lmproper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner's If you smell gas: information manual provided with this appliance. For assistance or • Shut off gas to the appliance. additional information consult a qualified installer, qualified technician •...
- Page 17 ● Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and should be inspected by a gas WARNING supplier. • The installation of this unit must adhere to local codes or Propane ●...
- Page 18 For assistance with damage. (if external tank) repair or replacement of the burner or any other parts, please contact COSTWAY. ● Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
- Page 19 Panel Door Min. Clearance G x1 H x1 60 in. (152.4 cm) Min. Clearance Min. Clearance 48 in. (121.9 cm) 48 in. (121.9 cm) Table Lid Metal Stand I x1 J x1 Fire Table Protective with Burner Cover K x1 L x1 Combustible materials should not be within 60 inches of the top of the unit, or within 48 inches around the entire unit.
- Page 20 Do not lock the screws until the assembly is complete. P x4 Q x4 R x12 P x12 Attach the panels E,E,G to the legs A,B,C,D Attach the metal stand (I) to the legs A,B,C,D using 12 pcs M6x35mm screws (R) and 12 using 4 pcs M6x25mm screws (Q) and 4 pcs pcs M6 washers (P).
- Page 21 Place propane gas tank (not included) into the metal stand (I). Make sure the gas tank sits on the metal stand (I) completely. Turn the preassembled wing screw on the outer part of metal stand (I) clockwise to secure the propane gas tank tightly. Put the glass panel (F) to the fire table (K).
- Page 22 lava Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections.
- Page 23 • Before performing any maintenance always disconnect propane gas Heating unit won’t Contact COSTWAY for a tank. Igniter pin is broken light replacement part • Store your product indoors during winter months. Avoiding extreme cold temperatures will prevent exposure damage.
- Page 24 Check that the gas tank isn’t No gas flow empty Turn the control knob to the ‘off’ position. Close the tank Sudden valve and disconnect propane drop in gas gas tank. Turn the control knob Excess flow safety valve flow to ‘high’;...