Page 1
All manuals and user guides at all-guides.com Transport GX18 B3095 Service Engineer’s Manual...
Page 2
All manuals and user guides at all-guides.com...
Page 3
TYAN products including liability or warranties relating to fitness for a par- ticular purpose or merchantability. TYAN retains the right to make changes to product descriptions and/or specifications at any time, without notice.
Page 4
All manuals and user guides at all-guides.com Federal Communications Commission (FCC) Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules Operation is subject to the following conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation.
Page 5
All manuals and user guides at all-guides.com About this Manual This manual provides you with instructions on installing your Transport GX18 B3095. This manual is intended for experienced users and integrators with hard- ware knowledge of personal computers. This manual consists of the following parts: —...
Page 6
All manuals and user guides at all-guides.com SAFETY INFORMATION Before installing and using the Trophy NR18 B3095, take note of the following precautions: — Read all instructions carefully. — Do not place the unit on an unstable surface, cart, or stand.
All manuals and user guides at all-guides.com Table of Contents Chapter 1: Overview About the Trophy NR18 B3095 Features Accessories Product View Chapter 2: System Setup Installing Motherboard Components 2.1.1 Removing the Chassis Cover 2.1.2 Installing CPU and Heatsink 2.1.3 Installing Memory 2.1.4 Installing the HDD...
Page 8
All manuals and user guides at all-guides.com...
All manuals and user guides at all-guides.com Chapter 1: Overview About the Transport GX18 B3095 Congratulations on your purchase of the TYAN Transport GX18 (B3095), a highly-optimized rack-mountable barebone system. The Transport GX18 (B3095) is designed to support single Intel® Yonah/Merom 2.33GHz pro- cessor with 667/533MHz FSB, providing a rich feature set and incredible performance.
All manuals and user guides at all-guides.com Features Enclosure — Industry 1U rack-mount chassis — Dimension: W 17.13” x D 15.47” x H 1.73” (W 435mm x D 393mm x H 43.5mm) — HDD Tray: 3.5” SATA HDD x 2 Processor —...
Page 11
All manuals and user guides at all-guides.com Front Panel I/O Ports — Serial port with D-Sub 9 pin connector x 1 — D-Sub 15 pin VGA Port x 1 — Two USB 2.0 ports with a dual-stacked USB connector + RJ-45 x 1 —...
Page 12
All manuals and user guides at all-guides.com Environmental Temperature — Operating temperature: 5 C ~ 35 — Non-operating temperature: -40 C ~ 70 Accessories — 1-to-1 PCI Riser Card x 1 (optional) — Al CPU Heatsink x 1 — Power Cord x 1 —...
All manuals and user guides at all-guides.com Product View This section shows the product from different angles. Chassis Internal View 1. Power Supply 2. Memory Slots 3. CPU Socket 4. 3.5” SATA HDD Bay (#1) 5.
Page 15
All manuals and user guides at all-guides.com System Front View USB x 2 Power Button System Rear View 1. USB Ports 2. COM Port 3. VGA Port 4. LAN Jack + USB Ports 5.
Page 16
All manuals and user guides at all-guides.com note...
All manuals and user guides at all-guides.com Chapter 2: System Setup Before You Begin This chapter explains how to install the CPU, CPU heatsink, memory mod- ules, and hard drives. Instructions on inserting a PCI card are also given. Take note of the precautions mentioned in this section when installing your system.
Page 18
All manuals and user guides at all-guides.com Precautions Components and electronic circuit boards can be damaged by discharges of static electricity. Working on a system that is connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to the Trophy NR18 or injury to yourself.
All manuals and user guides at all-guides.com Installing Motherboard Components This section describes how to install components on to the motherboard, including CPU, memory modules and PCI card. Follow these instructions to install the motherboard components. 2.1.1 Removing the Chassis Cover Step 1: Unscrew the chassis cover.
All manuals and user guides at all-guides.com 2.1.2 Installing CPU and Heatsink Step 1: Locate the CPU socket and place the CPU on top of it. Step 2: Screw to secure the CPU.
Page 21
All manuals and user guides at all-guides.com Step 3: Place the heatsink on top of CPU. Make sure to secure four (4) screws. Step 4: Screw to secure the heatsink.
All manuals and user guides at all-guides.com 2.1.3 Installing Memory Step 1: Press the locking levers to a fully open position. Step 2: Install memory in pairs of same type and density for optimal performance. Gently press down the memory until it sits firmly into the slots. The locking levers pop up into place.
All manuals and user guides at all-guides.com 2.1.4 Installing the HDD Step 1: First unscrew the HDD bay. Push the HDD bay backward and then lift it up. Step 2: Install the hard drive into the HDD bay, then secure the hard drive with six (6) screws.
Page 24
All manuals and user guides at all-guides.com Step 3: Screw the HDD bay back into the chassis and connect the SATA cable and power cord. Step 4: Unscrew the second HDD bay and remove it from the chassis. ...
Page 25
All manuals and user guides at all-guides.com Step 5: Screw the hard drive into the HDD bay and replace it to the chassis. Remem- ber to connect the HDD power cord and SATA cable.
All manuals and user guides at all-guides.com 2.1.5 Installing PCI Card (optional) Step 1: Unscrew the PCI card holder. Step 2: Push the PCI card holder open and move the dummy cover to the left to take it off. ...
Page 27
All manuals and user guides at all-guides.com Step 3: Install the PCI riser card into the PCI slot. Step 4: Connect the PCI card with the riser card. Screw the PCI card to the chassis. 2-11...
All manuals and user guides at all-guides.com Rack Mounting After installing the necessary components, the Trophy NR18 system can be mount- ed in a rack using the supplied rack mounting kit. • Mounting Ears x 2 + Screws • Extended Mounting Plates x 2 + Screws Installing the Server in a Rack Follow these instructions to mount the Trophy NR18 into an industry standard 19”...
Page 29
All manuals and user guides at all-guides.com Step 1: Measure the distance of inner side between the front and rear mounting brack- ets in the rack. Secure the mounting plate to the chassis with two screws for each side. Step 2: Lift and mount the chassis into the rack.
Page 30
All manuals and user guides at all-guides.com Step 3: Secure the mounting plate with 2 screws onto each side of chassis. Step 4: Secure the mounting plate with 2 screws onto each back side of the rack. 2-14...
All manuals and user guides at all-guides.com Appendix: BIOS Differences The following table displays the differences in BIOS between B3095 and S3095. For a complete review of S3095 BIOS, refer to the motherboard manual. S3095 Mainboard B3095 Barebone CPUFAN1 Fail Action...
(which can have expensive consequences). If these options are not available for you then Tyan Computer Corpora- tion can help.Besides designing innovative and quality products for over a decade, Tyan has continuously offered customers service beyond their expectations.
Page 33
All manuals and user guides at all-guides.com Help Resources: 1. See the beep codes section of this manual. 2. See the TYAN website for FAQ’s, bulletins, driver updates, and other information: http://www.tyan.com 3. Contact your dealer for help BEFORE calling TYAN.