Table of Contents
Advertisement
Chapter
2
Preparation
2
Thank you
Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual so that you fully
understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
Unpacking the TV
Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
TV
TV Stand (base)
GB
Instruction Manual
32" LED Smart HD TV
with built-in DVD player
LT-32C695(A) / LT-32C696(A)
Instruction Manual
JVC 32' LED Smart HD TV with built-in DVD player LT-32C695(A)_696(A) Manual.indd 7
for purchasing your new JVC TV.
Stand screws x6
TV Stand (neck)
Setup in
1
Quick Start Guide
15mins
32" LED Smart HD TV
with built-in DVD player
LT-32C695(A)/LT-32C696(A)
2
3
JVC 32' LED Smart HD TV with built-in DVD player LT-32C695(A)_696(A) Quick Start.indd 1-3
Quick Start Guide
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
The latest eco-friendly power-saving technology will switch off the TV if
4
experience. We would suggest that you allow about 15 mins for initial setup.
it is left on and idle for 4 hours. Please refer to "Auto Standby" under the
Connecting the Aerial and Turning on the TV
"Time Settings" section of the instruction manual for more detail.
Please follow this guide for a successful first time installation.
What's in the Box?
1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the ANT socket on the back of your TV.
2. Plug the TV into a mains socket and switch on at the mains.
Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.
3. In standby mode, press the
button on the remote control to turn the TV on. The LED indicator will flash for a few seconds then the TV will switch on.
TV
Remote Control/
Instruction Manual
Please inspect your TV for damage after unpacking. If
AAA Batteries x2
TV Stand
Quick Start Guide
you do notice any damage please consult your dealer.
Operating Your Remote Control
LAN
SPDIF
VGA
1. Slide open the battery compartment on the back of the remote control.
Optic.OUT
AV IN
2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of
the batteries with the (+) and ( - ) ends indicated in the battery compartment.
LAN
3. Slide the battery compartment cover back into place. Make sure it clicks into place.
For extra safety use the screw supplied to screw the battery compartment closed.
VGA
SPDIF
Installing the Base Stand
Optic.OUT
Fitting the Stand to the TV
1. Fit the neck onto the base.
2. Using 2 of the supplied screws, screw the neck to the base.
AV IN
3. Ensure the TV is switched off and not connected to the mains power supply.
4. Lay the TV down on a flat surface ideally on the edge of a table so the base of the TV slightly overhangs
the edge of the table, with the back side facing up. Please make sure a soft cushioned material (such as a
dry bath towel or thick piece of foam) is placed beneath the screen.
5. Slide the stand under the lip, the neck will fit snugly over the screw holes. Then screw the stand to the
RF coaxial cable
TV using the 4 screws supplied.
(not included)
For wall mounting instructions please refer to your Instruction Book.
Router
(not included)
LAN
SPDIF
VGA
Optic.OUT
AV IN
Optional
If you want to connect to the internet via a wired connection
Slide under
then connect your ethernet cable to the LAN socket.
the lip
Cushioned
Protective
Table
material
bag
• Do not connect the TV to the mains supply until you have completed all the connections.
• Always disconnect the TV from the mains socket when not in use for a long period of time.
The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object, or
• The
button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.
anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the
screen could crack.
To completely disconnect the mains power, please remove the mains plug from the mains socket.
LANG.
LANG.
G
BACK
EXIT
Remote Control /
AAA Batteries x 2
04/10/2019 09:01
7
04/10/2019 09:03
Advertisement
Table of Contents
