Advertisement
技术要求
1.印刷为黑白色单色，正反面印刷；
2.所有印刷内容正确、清晰，不得有漏印、误印，无印刷缺陷；
3.幅面：（210±3）X（145±3），（单位：mm）；
4.未注公差按照GB1800(现行).IT15；
5.颜色及整体效果必须经过研发部确认后方能生产，产品检验以封样件为准；
6.符合RoHS现行标准要求和REACH指令。
1995486
英-长兴HV-6系列
新欧标
版本号
设计
刘大燕 2018.08.04
审 核
崔维明 2018.08.04
工 艺
张梅娥 2018.08.04
标准化
程木聪 2018.08.04
后附图纸12页
B
XECN002958
更改单编号
会签
会签
刘松
批准
石伟泽 2018.08.04
80g双胶纸
重 量
第
张 共
2018.08.04
图形识别符号
比 例
使用说明书
张
X08060351
Advertisement
Table of Contents
Related Manuals for Hisense WFHV6012
Summary of Contents for Hisense WFHV6012
- Page 1 后附图纸12页 技术要求 1.印刷为黑白色单色，正反面印刷； 2.所有印刷内容正确、清晰，不得有漏印、误印，无印刷缺陷； 3.幅面：（210±3）X（145±3），（单位：mm）； 4.未注公差按照GB1800(现行).IT15； 5.颜色及整体效果必须经过研发部确认后方能生产，产品检验以封样件为准； 6.符合RoHS现行标准要求和REACH指令。 1995486 英-长兴HV-6系列 新欧标 80g双胶纸 XECN002958 更改单编号 版本号 重 量 比 例 使用说明书 设计 会签 刘大燕 2018.08.04 会签 审 核 第 张 共 张 刘松 2018.08.04 崔维明 2018.08.04 X08060351 工 艺 张梅娥 2018.08.04 图形识别符号...
- Page 2 S ’ X08060351B , t i...
-
Page 3: Removing The Filter
INSTRUCTIONS FOR USE SAFETY INFORMATION BEFORE USING THE WASHING MACHINE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE OPENING I CLOSING DOOR CHILD SAFETY (IF AVAILABLE) BEFORE THE FIRST WASH CYCLE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES REMOVING THE FILTER DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE... -
Page 4: Safety Information
SAFETY INFORMATION The manufacturer reserves the right for any modifications on the product which might be deemed necessary or useful without informing about it in this IFU. Before operating your new washing machine, please read this instruction carefully, and keep it for future reference. If you have lost it accidentally, ask customer service for e- copy or hard copy. - Page 5 For appliances with ventilation openings in the base, that a carpet must not obstruct the openings. Children of less than 3 years should be kept away unless ensure continuously supervised. The maximum permissible inlet water pressure, 1 MPa, for appliances intended to be connected to the water mains. The minimum permissible inlet water pressure, 0.1 MPa, if this is necessary for the correct operation of the appliance.
- Page 6 that that The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for there cyclingof electrical and electronic equipment.
-
Page 7: Description Of The Washing Machine
BEFORE THE FIRST WASH CYCLE Clean the outside of the washing machine with a damp cloth. Do not use abrasive detergents. To remove any residual water used during testing by the manufacture r, we Never open the door forcibly or use it as a step. recommend that you carry out a short wash cycle without laundry. - Page 8 / soak...
- Page 9 Depending on the model, Insert removal tool like slotted screwdriver into the small opening of bottom baffle, press the bottom baffle downward with much strength and open it. Or, push down on the tabs provided on both the sides and remove it. unds...
- Page 11 solv and Choose the desired programmme to start the machine. The washing machine will not start, and the screen flashes. Check if the water tap is closed. remove some the screen is flashing. Press the the screen is flashing.
- Page 12 Hot / Cold fill fault - For Models with Dual Inlets Fault Code List If you wish to connect hot and cold water supply (Fig.1): Displayed on Display Window Fault Description 1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red filter on the rear side of machine.
-
Page 13: Fault Code
C. Fault code The washer stops when the program is running. The display window shows fault code “F02/F24”, fault codes from “F04’ to “F07”, “F13”,“F14”, “F23” or “Unb”. If fault code “F02/F24” is shown Water level reaches overflow level. Remove it by pressing “Start/Pause” key and feed water. Select and start required program.