Toggle Bolts; Top Cabinet; Installation Instructions - GE PVM9179BRTS Installation Instructions Manual

RECIRCULATING
A
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Check Blower Orientation
A4. Adapting Microwave Blower For Recirculation
A5. Mount the Oven
A6. Installing The Charcoal Filter
A1 ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts and
wood screws. At least one wood screw must be
used to attach the plate to a wall stud.
Remove the toggle wings from the bolts.
1
Insert the bolts into the mounting plate through
2
the holes designated to go into drywall and
reattach the toggle wings to
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
12

Installation Instructions

(Non-Vented Ductless)
IMPORTANT: Do NOT
remove the cardboard spacers
between the heat shield and
door
3 4
Bolt End
3/8" TO EDGE OPTION 2
12" STEP 1: Installer uses bracket to make 2 marks. First
OPTION 1 mark is made by using the stampled slot in bracket. Second mark is made on the ouside edge of bracket.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS F. CUT OUT FOR HORIZONTAL
BEFORE PROCEEDING WITH THIS Horizontal line
REAR WALL TEMPLATE. 4" OUTSIDE EXHAUST
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet. CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
1. Use a level to check that the template is positioned Make a mark here, Make a mark here, along STEP 4:
2. Locate and mark at least one stud on the left or accurately. bottom of even with stamped slot provided. inside bottom of the
right side of the centerline. slot stamped
NOTE: It is important to use at least one wood
screw mounted firmly in a stud to support the weight STEP 2:
of the microwave. Mark two additional, evenly spaced the cabinets and makes 2 more marks. Marks are the Installer moves bracket to the other side of
locations for the supplied toggle bolts. same as STEP 1, just opposite side.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for

toggle bolts.

NOTE:: D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Make a mark here, along even with mark here, Make a
Darle vuelta a la hoja para consultar la inside bottom of the stamped slot provided stamped bottom of
versión en Español. (same as Step 1). slot
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE NOTES:
30" MINIMUM WIDTH REQUIRED - 13" Max Cabinet Depth
Locate and mark holes to align with holes in the - 15" deep cabinets require additional steps using
mounting plate. an additional installation kit: JX36BUMP
IMPORTANT: REAR WALL TEMPLATE
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Trim the rear wall template along the dotted line.
A
C
D
B
3 Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
CAUTION
Be careful to avoid pinching
fingers between the back of the mounting plate
and the wall.
Tighten all bolts. Pull the plate away from the wall
4
to help tighten the bolts.
A2
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
Wear safety goggles when drilling
CAUTION
holes in the cabinet bottom.
31-7000092 Rev. 3