Storage Recommendations; Assembly And Adjustments - DeWalt Impact Connect DWAPVCIR Instruction Manual

English
b. Inspect tool and attachments before use for any loose
or missing parts. Never attempt to repair or use a
damaged PVC/PEX cutter, brace or other attachment.
Replace with a new cutter or brace.
c. This tool produces large forces that can break
attachments or parts and cause injury. Always be
attentive and take proper safety precautions, including
wearing eye protection.
d. Before operating, inspect job site for hazards including
chemicals or waste that could remain in pipes.
e. Before operating, read and understand all safety
and operating instructions including the fitting
manufacturer's installation instructions and the
instructions for any other equipment used with this
tool. Failure to follow all instructions and warnings
may result in property damage and/or serious
personal injury.
f. Keep the cutting area of the attachment free from
hands and other objects while the tool is in use.
Fingers could be crushed or cut.
g. For best results, always clamp or anchor the material
to be cut.
h. Cutting operations may cause material pieces to fly.
Flying particles can cause permanent eye damage.
ALWAYS wear eye protection.
i. Always wear gloves when operating tool and handling
materials. The ends of the materials can be sharp and
cause serious personal injury.
j. To reduce the risk of explosion, electric shock and
property damage, never cut gas lines, electrical lines,
or full water lines. Shut off water and drain lines before
making a cut.

Storage Recommendations

The best storage place is one that is cool and dry, away from
direct sunlight and excess heat or cold.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
6
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all documentation
..................... do not expose to rain

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.

WARNING: Never modify this device or any part of
it. Damage or personal injury could result.
Attach the Universal Brace Bracket
(Fig. B - D)
1. Remove battery from impact Driver. Do not reinstall
battery until AFTER the Brace Bracket is installed.
2. Loosen the back knob
wide enough to slip the Impact Driver through (as shown
in Fig. B).
3. Slide the Impact Driver into the Brace Bracket from the top
(as shown in Fig. C).
4. Place the Impact Driver and Brace Bracket on a FlAT surface.
5. Compress the front end together until the Brace Bracket
is snug around the Impact Driver foot, then tighten the
back knob. Both sides should remain parallel during
tightening (as shown in Fig. D).
Attach the Brace Arm and Impact Connect
Attachment (Fig. E - G)
1. Loosen both yellow arm knobs
attachment shank 4
shown in Fig. E).
2. Rotate the arm joint
7 clicks into the bar channel
clicking as you rotate. The yellow slide lock
secure the bar in place (as shown in Fig. F).
3. Ensure the shank is parallel to the ground and finger
tighten all knobs (as shown in Fig. G).
4. Reinstall battery AFTER installation and prior to use.
Scan QR code for installation video.
Replacing Blade (Fig. H)
1. The blade should be fully advanced with the blade cover
installed as the initial step.
2. Advance blade 10 all the way forward by holding the
trigger on the impact driver.
3. Remove battery from impact driver.
1 until the Brace Bracket
3 one turn and insert the
into the impact driver chuck
5 and the arm slider 6 until the bar
8 . There will be an audible
9
2 can open
17 (as
should