Table of Contents
  • Table of Contents
  • Advertencias y Precauciones
  • Instalación Típica
  • Instalación en una Construcción Nueva
  • Instalación en Modernizaciones
  • Funcionamiento
  • Limpieza y Mantenimiento
  • Identificación y Solución de Fallas
  • Repuestos
  • Garantía

Advertisement

Available languages

Available languages

Quick Links

READ AND SAVE
THESE INSTRUCTIONS
Installer: leave this guide with homeowner.
Register your product online at www.broan.com/register.
Easy installation in both
new construction and retrofit
© 2014 Broan-NuTone LLC
RB80L
RB110L
n
ULTRA Pro
TM
Ventilation Fan / Light / Night Light
with ULTRAQuick
TM
INSTALLATION GUIDE
Table of Contents
Warnings and Cautions
Typical Installation
New Construction Installation
Retrofit Installation
Operation
Cleaning and Maintenance
Troubleshooting
Service Parts
Warranty
Installation Technology
2
2
3
7
12
12
13
13
14

Advertisement

Table of Contents
loading

Summary of Contents for Broan ULTRA Pro RB80L

  • Page 1 ULTRA Pro THESE INSTRUCTIONS Ventilation Fan / Light / Night Light Installer: leave this guide with homeowner. with ULTRAQuick Installation Technology Register your product online at www.broan.com/register. INSTALLATION GUIDE Table of Contents Warnings and Cautions Typical Installation New Construction Installation...
  • Page 2 GFCI (Ground Fault Circuit Interrupter) - protected branch circuit. 8. Use an ON/OFF switch, timer, or speed control to operate this ventilator. Use of speed control other than the Broan 78V and 78W may cause a motor humming noise. 9. This unit must be grounded.
  • Page 3 Page 3 RB80L RB110L Installation Guide New Construction Installation Tools needed Materials needed • Power screwdriver with a Phillips bit • 4" round metal ducting recommended for best performance. Use of other ducting is acceptable but may impact performance. • Phillips screwdriver •...
  • Page 4 Page 4 RB80L RB110L Installation Guide New Construction Installation Snap-in and Secure Housing Position Housing between joists and crimp channel on both sides of Mounting Frame to lock Housing in place. Do not crimp Housing. Screws from Parts Bag Attach Flange, Transition and Ducting Top and bottom flanges Screw from go outside Housing...
  • Page 5 Page 5 RB80L RB110L Installation Guide New Construction Installation Connect Wires and Install Knockout Plate • Run 120VAC electrical wiring to the installation location. • Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag. •...
  • Page 6 Page 6 RB80L RB110L Installation Guide New Construction Installation Insert Mask and Finish Ceiling • Install ceiling material. • Cut out around Housing. Mask protects unit during construction. Remove before installing Grille. Install Grille Install Bulbs Night Light (purchase separately) See Page 12 for Operation and Cleaning and Maintenance.
  • Page 7 Page 7 RB80L RB110L Installation Guide Retrofit Installation Tools needed Materials needed • Power screwdriver with a Phillips bit • Ruler • Tape to seal duct connections • Phillips screwdriver • Pencil • Existing rigid duct will require the addition of a short length of flexible duct •...
  • Page 8 Page 8 RB80L RB110L Installation Guide Retrofit Installation Remove Blower Assembly Set aside Blower Assembly Both sides Remove Wiring Panel Set aside Wiring Panel Set aside screw Insert Mounting Frame Remove screws from Mounting Frame Bend up and set aside four tabs...
  • Page 9 Page 9 RB80L RB110L Installation Guide Retrofit Installation Secure Mounting Frame Screws set aside in Step 7 Snap-in Housing Pull existing wiring into Housing as it is inserted into Mounting Frame Attach Flange, Transition, and Ducting Screw from Parts Bag Pull existing 4"...
  • Page 10 Page 10 RB80L RB110L Installation Guide Retrofit Installation Install Knockout Plate, Connect Wires and Install Wiring Panel • Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag. • Connect wires as shown in wiring diagram. •...
  • Page 11 Page 11 RB80L RB110L Installation Guide Retrofit Installation Insert and Secure Blower Assembly Screws from Parts Bag If ceiling repairs are needed, place Mask in Housing after Blower Assembly is secured. See New Construction Installation Step 6. Install Grille Remove Mask before installing Grille.
  • Page 12 To Operate Fan Refer to Retrofit Installation Step 14 (above). Use an ON/OFF switch, timer, or speed control to operate 1. Carefully insert a small this ventilator. Use of speed control other than the Broan M.O.L. 3.9" (100 mm) flathead screwdriver 78V and 78W may cause a motor humming noise.
  • Page 13 Page 13 RB80L RB110L Installation Guide Troubleshooting Service Parts Symptom: The fan does not run. • Check for an open fuse or circuit breaker in the building’s service panel. • Check that the plug-in connection for the Motor is seated firmly in place.
  • Page 14 Fan or part thereof, to the extent Broan finds it to be covered by and in breach of this limited warranty. Broan will ship the repaired or replaced Fan or replacement parts to you at no charge.
  • Page 15: Table Of Contents

    Ventilador / Lámpara / Lámpara de noche Instalador: entregue esta guía al dueño de casa. con la tecnología de instalación ULTRAQuick Registre su producto en línea en el sitio www.broan.com/register. GUÍA PARA LA INSTALACIÓN Tabla de contenido Advertencias y precauciones Instalación típica...
  • Page 16: Advertencias Y Precauciones

    8. Utilice un interruptor ENCENDIDO / APAGADO, el temporizador, o de control de velocidad para usar este ventilador. El uso de un control de velocidad que no sea la Broan 78V y 78W puede causar un zumbido del motor. 9. Esta unidad debe estar conectada a tierra.
  • Page 17: Instalación En Una Construcción Nueva

    Página 3 RB80L RB110L Guía para la instalación Instalación en una construcción nueva Herramientas necesarias Materiales necesarios • Destornillador eléctrico con punta Phillips • Conducto circular de metal de 4 pulg. recomendado para un mejor • Destornillador Phillips rendimiento. Se acepta el uso de otro tipo de conducto pero esto puede afectar el rendimiento. •...
  • Page 18 Página 4 RB80L RB110L Guía para la instalación Instalación en una construcción nueva Coloque el compartimiento a presión y asegúrelo ¡Presione hasta que trabe! Ubique el compartimiento entre las vigas y ajuste el canal a ambos lados del bastidor de montaje para que el compartimiento quede asegurado en su lugar.
  • Page 19 Página 5 RB80L RB110L Guía para la instalación Instalación en una construcción nueva Conecte los cables e instale la placa metálica • Extienda un cableado eléctrico de 120 VCA hasta el sitio de la instalación. • Utilice conectores aprobados por UL para asegurar el cableado hasta la placa metálica que se incluye en la bolsa de piezas. •...
  • Page 20 Página 6 RB80L RB110L Guía para la instalación Instalación en una construcción nueva Introduzca la máscara y acondicione el techo La máscara protege • Instale el material del techo. la unidad durante la construcción. Retírela • Corte alrededor del antes de instalar la compartimiento.
  • Page 21: Instalación En Modernizaciones

    Página 7 RB80L RB110L Guía para la instalación Instalación en modernizaciones Herramientas necesarias Materiales necesarios • Destornillador eléctrico con punta Phillips • Regla • Cinta para sellar las conexiones de los conductos • Destornillador Phillips • Lápiz • Los conductos rígidos existentes requerirán el •...
  • Page 22 Página 8 RB80L RB110L Guía para la instalación Instalación en modernizaciones Retire el conjunto del ventilador Aparte el conjunto del ventilador Ambos lados Retire el panel con los cables Aparte el panel con los cables Aparte el perno Introduzca el bastidor de montaje Retire los pernos del bastidor de montaje...
  • Page 23 Página 9 RB80L RB110L Guía para la instalación Instalación en modernizaciones Asegure el bastidor de montaje Pernos apartados en el Paso 7 Coloque el compartimiento a presión ¡Presione hasta que trabe! Tire del cableado existente en el compartimiento mientras lo introduce en el bastidor de montaje Fije el reborde, la transición, y los conductos Perno de la...
  • Page 24 Página 10 RB80L RB110L Guía para la instalación Instalación en modernizaciones Instale la placa metálica, conecte los cables e instale el panel de cableado • Utilice conectores aprobados por UL para asegurar el cableado hasta la placa metálica que se incluye en la bolsa de piezas. •...
  • Page 25 Página 11 RB80L RB110L Guía para la instalación Instalación en modernizaciones Introduzca y asegure el conjunto del ventilador Pernos de la bolsa de piezas Si fuera necesario efectuar reparaciones en el techo, coloque la máscara en el compartimiento después de asegurar el conjunto del ventilador. Consulte el Paso 6 de Instalación en una construcción nueva.
  • Page 26: Funcionamiento

    El uso de un control de velocidad que no sea y la lente, luego gire para retirar la lente. la Broan 78V y 78W puede causar un zumbido del motor. 2. Compre dos (2) lámparas fluorescentes tipo GU24 de Funcionamiento de las luces 18W (máx.), con una longitud máxima general (MOL) de...
  • Page 27: Identificación Y Solución De Fallas

    Página 13 RB80L RB110L Guía para la instalación Identificación y solución de fallas Repuestos Síntoma: El ventilador no funciona. • Verifique la presencia de un fusible o interruptor abierto en el panel de servicios del edificio. • Verifique que la conexion del motor está bien unidas. •...
  • Page 28: Garantía

    Esta garantía cubre sólo el reemplazo o la reparación de los Ventiladores o piezas con defectos del mismo en la plana principal de Broan y no incluye los costos del transporte del servicio en campo ni los gastos de estadía.

This manual is also suitable for:

Ultra pro rb110l

Table of Contents