Radio Shack 2003 Hummer H2 60-4358 - Motorized Toy Car Manual

Step 1. Installing the Batteries

You will need...

• One 9V Battery for the Transmitter
• One 9V Battery for the Hummer H2
• One 7.2V Rechargeable Battery Pack

Install Batteries in Hummer H2

• Turn off the Hummer H2.
• Remove the battery compartment cover.
  
• Place the 9V battery in the battery compartment, matching the polarity symbols (+ and -) as marked inside.
• Place the battery pack in the recessed area with the battery pack's connector on the same side as the Hummer H2's matching connector.
• Attach the battery pack's connector to the Hummer H2's matching connector. They fit together only one way. Do not force them.
• Close the cover.

You must charge the battery pack with a battery charger (not supplied), available at your local RadioShack store.

Install Battery in the Transmitter

• Turn the transmitter off.
• Slide the battery compartment cover in the direction of the arrow to open it.
  
• Place the 9V battery in the com-partment, matching the polarity symbols (+ and -) as marked inside.
• Replace the cover and snap it shut.

What's Included

• Hummer H2
• Transmitter
• Box Wrench
• Plastic Antenna Tube
• Owner's Manual

Step 2. Installing the Antenna Tube

• Route the antenna wire's loose end through the supplied antenna tube.
• Insert the antenna tube securely into the Hummer H2's antenna tube hole at the top of the vehicle.

Step 3. Driving the Hummer H2

• Extend the transmitter's antenna to its full length for best reception.
• Turn on the transmitter and the Hummer H2. The headlights and the LED indica-tor illuminate.
• Select the specific fre-quency by setting the Band ABC switch on the transmitter and the Hummer H2 to the same band.
  
• Use the transmitter's speed control trigger to move forward and reverse. Pull the trigger toward the handle to move forward. The head-lights illuminate. Pull all the way back for maximum speed. Push the trigger away from the handle to move backward. The taillights illuminate. Release to stop.
  
• Use the transmitter's steer-ing wheel control to turn the Hummer H2 left and right. Release the steering wheel to drive straight.
• Turn the transmitter and the vehicle off when you finish playing with it.

Removing the Hummer H2's wheels

Use the box wrench to remove and/or replace the Hummer H2's wheels.

Step 4. Adjusting the Trim Controls

Trim I

The transmitter's neutral trim control lets you fine-tune the speed control so the Hummer H2 stops completely when you release the speed control to its center position. If Trim I is set too far to the left, the vehicle will move backward. If it is set too far to the right, the vehicle may continue forward.

Trim II

The transmitter's steering trim control lets you fine-tune the steering so the Hummer H2 drives in a straight line. If it is set too far to the left or right, the vehicle may drive in those directions.

• Turn the Hummer H2 over on its side so the tires do not touch the ground.
• Turn on the transmitter and the Hummer H2.
• If the tires move, turn Trim I until the tires stop.
• If the front tires appear to angle left or right, adjust Trim II until the tires appear to be straight.
• When you finish your adjustments, turn off the transmitter and the Hummer H2.

Do not touch the tires or the steering control during this adjustment. You may have to fine-tune the trim controls after using the Hummer H2 for a while.

Never set Trim I to make the Hummer H2 continually move.

Care & Use

• Use extreme care when running the Hummer H2. It can reach much higher speeds (up to 1200 feet per minute) than most remote-controlled cars.
• Avoid high-impact collisions with peo-ple or objects when you drive the Hummer H2.
• Do not touch the motor immediately after using the Hummer H2, as it might become hot during use.
• Do not play with your Hummer H2 in the street.
• If your Hummer H2 gets stuck under an object, immediately release the transmitter's control levers and retrieve the Hummer H2.
• Keep the Hummer H2 dry. If it gets wet, dry it immediately. Use and store the Hummer H2 in normal temperature environments.
• Wipe the Hummer H2 with a damp cloth to keep it looking new. Keep it away from dust and dirt.

Overview of the Hummer H2

Front View of Hummer H2

Rear View of Hummer H2

Helpful Hints

• Your Hummer H2 comes in three frequencies so you and your friends can play together. If you race other remote-controlled cars, be sure to set your Hummer H2 and transmitter to a different frequency than your playmate.
• Driving your Hummer H2 for long periods of time can cause a high heat level, which causes wear and tear on the motor. To help keep heat levels down, let your vehicle cool for 10 minutes before installing a new battery pack.
• If you want to run your Hummer H2 for extended periods, we suggest you buy an extra battery pack. You can charge one while you use the other.
• If the Hummer H2 moves slowly or not at all, and you have installed a fresh battery pack, check the wheel mechanisms for lint, hair, dust or thread.
• If the Hummer H2's motor runs, but does not respond to the transmitter, move closer to the Hummer H2 and try again.
• If someone uses a CB nearby, it might interfere with control of your Hummer H2. If this happens, move your Hummer H2 away from the CB. You cannot operate the Hummer H2 near devices with transmitters that use the same frequency as your Hummer H2 (27 MHz with three bands).
• If the Hummer H2 does not drive in a straight line, adjust the wheel alighment control on the side of the Hummer H2. If it pulls to the right, slide the control toward L. If it pulls to the left, slide the control toward R.
  

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Radio Shack 2003 Hummer H2 60-4358 - Motorized Toy Car Manual