Advertisement
ENGLISH
General description
.
A 2D Contour Tracking beard trimmer comb
B Trimming attachment
C Hair length selector
D Release button
E On/off slide
F Socket for appliance plug
G Cleaning brush
H Barber's comb
I Charging light
J Powerplug
K Appliance plug
L Nose/ear/eyebrow attachment
M Charging stand with storage facility
N Precision attachment
O Hair clipper comb (non-flexible)
P Micro shaver
Important
.
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗ Check if the voltage indicated on the
powerplug corresponds to the local mains
voltage before you connect the appliance.
◗ Only use the powerplug supplied to charge
the appliance. Do not cut off the powerplug
to replace it with another plug, as this will
cause a hazardous situation.
◗ If the powerplug is damaged, always have it
replaced by one of the original type in order
to avoid a hazard.
◗ Make sure the appliance, the charging stand
and the powerplug do not get wet.
◗ Charge, use and store the appliance at a
temperature between 15cC and 35cC.
◗ This appliance is only intended for trimming
and grooming the human beard, moustache,
sideburns, nose hair, ear hair and eyebrows.
◗ Keep the appliance out of the reach of
children.
◗ Do not use the appliance when one of the
attachments is damaged or broken, as this
may cause injury.
◗ Do not place the beard trimmer comb or the
hair clipper comb on the precision
attachment.
Charging
.
Charge the appliance fully before you start using it
for the first time or after a long period of disuse.
It will take approx. 10 hours to fully charge the
battery. A fully charged appliance has a cordless
operating time of up to 35 minutes. When you
charge the appliance for 3 hours, you can use it for
15 minutes.
The appliance does not run from the mains.
Make sure the appliance is switched off during
charging!
You can charge the appliance in 2 different ways:
1
In the charging stand:
◗ Insert the appliance plug into the socket in the
bottom of the stand (fig. 1).
◗ Place the appliance on the pin of the stand
(fig. 2).
2
Outside the charging stand:
◗ Insert the appliance plug directly into the
appliance (fig. 3).
◗ In both situations the charging light on the
powerplug indicates that the appliance is
charging (fig. 4).
Optimising the lifetime of the rechargeable
battery
◗ Do not leave the appliance plugged into the
wall socket for more than 24 hours.
◗ Discharge the battery completely twice a year
by letting the motor run until it stops. Then
fully recharge the battery.
Preparing for use
.
◗ Always comb the hair with the barber's comb
in the direction of growth before you start
trimming.
◗ Make sure that the hair is dry and clean.
Trimming
.
Beard trimming with comb
1
Put the beard trimmer comb on the trimming
attachment and push it home until you hear a
click (fig. 5).
2
Press the hair length selector and slide it to
the desired setting. See table I (fig. 6).
The setting selected will appear in the window to
the left of the hair length selector.
When you are trimming for the first time, start at
B
the maximum trimming length setting (9) to
familiarise yourself with the appliance.
B
Using setting 1 with the comb installed will result
in a 'stubble look'.
3
To trim in the most effective way, move the
appliance against the direction of hair growth
(fig. 7).
Do not move the appliance too fast. Make smooth
and gentle movements and make sure the surface
of the comb always stays in contact with the skin.
◗ Regularly remove the comb to blow and/or
shake out hair that has accumulated.
NB: You have to adjust the trimming length again
after you have removed the comb!
Beard trimming without comb
1
Remove the comb by pressing and sliding the
hair length selector upwards (fig. 8).
Never pull at the flexible top of the comb. Always
pull at the bottom part.
2
Make well-controlled movements and touch
your beard only slightly with the trimming
attachment.
Cutting without the comb will result in a very short
stubble beard.
Defining beard, moustache and sideburns
1
Remove the beard trimmer comb by pressing
and sliding the hair length selector upwards
(fig. 8).
2
Detach the trimming attachment by pushing
the release button (fig. 9).
3
Put the precision attachment on the appliance
(fig. 10).
◗ Hold the appliance upright when you use the
precision attachment (fig. 11).
Grooming facial hair (nose hair, ear hair and
eyebrows)
1
Remove the comb (fig. 8).
2
Remove the trimming attachment (fig. 9).
4203 000 31202
3
Put the nose/ear/eyebrow attachment on the
appliance (fig. 12).
Trimming nose hair
1
Make sure your nostrils are clean.
2
Switch the appliance on and insert the tip of
the attachment into one of your nostrils
(fig. 13).
Do not insert the tip more than 0.5 cm into your
nostril.
3
Slowly move the tip in and out while turning it
round at the same time to remove unwanted
hair.
To reduce the tickling effect, make sure that the
side of the tip is firmly pressed against the skin.
Trimming ear hair
1
Clean the outer ear channel. Make sure it is
free from wax.
2
Switch the appliance on and move the tip
softly round the ear to remove hairs sticking
out beyond the rim of the ear (fig. 14).
3
Carefully insert the tip into the outer ear
channel (fig. 15).
Do not insert the tip more than 0.5 cm into the
ear channel as this could damage the eardrum.
Trimming eyebrows
Use the tip to cut individual eyebrow hairs.
Do not use the appliance to define or trim the
entire eyebrow.
Never try to trim your eyelashes.Never come too
close to your eyes!
1
Place the tip of the attachment on the upper
edge of the eyebrow.
2
Move it along the edge of the eyebrow from
the base of the nose towards the outer tip of
the eyebrow (fig. 16).
Hair clipping
.
Preparing for clipping
Make sure that the appliance is fully charged before
you start clipping.
It is not possible to run the appliance from the
mains when the battery is empty.
◗ Before you start clipping, make sure that the
head of the person whose hair you intend to
cut is at the same level as your chest so that
all parts of his head are clearly visible and
within easy reach.
◗ Only use the appliance on dry hair. Do not
use it on freshly washed hair.
◗ To achieve optimal clipping results, always
move the appliance slowly through the hair
against the direction of hair growth.
◗ Comb the hair in the direction of growth.To
achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Clipping with comb
1
Put the hair clipper comb on the trimming
attachment and push it home ('click') (fig. 17).
2
Press the hair length selector and slide it to
the desired setting. See table 2.
2/3
Advertisement
