Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

Philips QG3030/20 User Manual

Philips multigroom grooming kit qg3030.

 
QG3030
2
5
8
11
14
1
17
20
English
3
4
introduction
Congratulations on your purchase and welcome
to Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
6
7
general description (Fig. 1)
A 2D Contour Tracking beard trimming comb
(flexible)
B Micro shaver
C Precision attachment
D Trimming attachment
9
10
E Appliance plug
F Adapter
g Charging light
h Cleaning brush
i
Socket for appliance plug
J
On/off slide
12
13
K Release button
l Hair length selector
important
Read this user manual carefully before you use the
appliance and save it for future reference.
15
16
Danger
-
Make sure the adapter and the appliance do
not get wet.
Warning
-
Check if the voltage indicated on the adapter
and on the appliance corresponds to the local
18
19
mains voltage b efore you connect the
appliance.
-
The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
-
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible
for their safety.
-
Children should be supervised to ensure that
they do not play with the appliance.
Caution
-
Use, charge and store the appliance at a
temperature between 15°C and 35°C.
-
Only use the adapter supplied to charge the
appliance.
-
If the adapter is damaged, always have it replaced
with one of the original type in order to avoid
a hazard.
-
Do not use an attachment or comb if it is
damaged or broken, as this may cause injury.
-
This appliance is only intended for
trimming the human beard, moustache and
sideburns, shaving the human beard line and
contouring human scalp hair. Do not use it for
any other purpose.
-
If the appliance is subjected to a major change
in temperature, pressure or humidity, let the
appliance acclimatise for 30 minutes before
you use it.
-
Do not place the beard trimming comb on the
precision attachment.
Compliance with standards
-
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in
this user manual, the appliance is safe to use
based on scientific evidence available today.
Charging
Charge the appliance fully before you use it for the
first time or after a long period of disuse.
It takes approx. 10 hours to charge the battery
fully. A fully charged appliance has a cordless
operating time of up to 35 minutes. When you
charge the appliance for 3 hours, you can use it for
15 minutes.
The appliance does not run from the mains.
Make sure the appliance is switched off during
charging.
Insert the appliance plug directly into the
1
appliance (Fig. 2).
The charging light on the adapter indicates
,
that the appliance is charging. (Fig. 3)
Optimising the lifetime of the
rechargeable battery
-
Do not leave the appliance connected to the
mains for more than 24 hours.
-
Discharge the battery completely twice a year
by letting the motor run until it stops. Then
fully recharge the battery.

Summary of Contents

  • Page 1

    QG3030 English introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. general description (Fig. 1) A 2D Contour Tracking beard trimming comb (flexible) B Micro shaver...

  • Page 2

    (Fig. 13) If you have any difficulties obtaining replacement attachments or combs for your appliance, contact the Philips Consumer Care Centre in your country or consult the worldwide guarantee leaflet. Environment Do not throw away the appliance with the...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: