Page 1 Please access our websites for further information. The U.S. mainland www.toyota.com Hawaii www.toyotahawaii.com © 2006 TOYOTA MOTOR CORPORATION All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.
Page 2 Important information about this manual Safety and vehicle damage warnings Safety symbol Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows: CAUTION This is a warning against anything which may...
Page 3 None of these systems, either indi- Toyota encourages you and your family to take the time vidually or together, can ensure that there is no injury to read Section 1−3 of this Owner’s Manual carefully.
Page 4 Toyota recommends you to read the provisions in Sec- D Engine speed tion 1−3 carefully and refer to them as needed during your time of ownership of this vehicle.
Page 5 D SRS airbag deployment data Toyota will not disclose the data recorded in an EDR to a third party except when: D SRS airbag system diagnostic data D An agreement from the vehicle’s owner (or the leas- If your vehicle is equipped with a vehicle stability con-...
Page 6 New vehicle warranty Important health and safety information about your Toyota Your new vehicle is covered by the following Toyota limited warranties: D New vehicle warranty CAUTION D Emission control systems warranty D Others WARNING: Engine exhaust, some of its constitu- For further information, please refer to the “Owner ’s...
Page 7 TEMS, SRS airbag system and seat belt pretensioner system, This vehicle should not be modified with non−genuine be sure to check with your Toyota dealer for precaution- Toyota products. Modification with non−genuine Toyota ary measures or special instructions regarding installa- products could affect its performance, safety or durabili- tion.
Page 8 Owner’s Manual. For details about tire infla- service shop or by your Toyota dealer before you dis- tion pressure and load limits, see pages 330 and pose of your vehicle.
Page 9 Leak detection pump On−pavement and off−road driving tips This pump performs fuel evaporation leakage check. This check is done approximately five hours after the This vehicle belongs to the utility vehicle class. Utility engine is turned off. So you may hear sound coming vehicles have a significantly higher rollover rate than from underneath the luggage compartment for several other types of vehicles.
Page 11 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview ........Instrument cluster overview .
Page 12 Instrument panel overview "View A 1. Side vents 2. Side defroster outlets 3. Instrument cluster 4. Center vents 5. Electric moon roof switches and/or personal lights 6. Tire pressure warning select switch (in the glove box) 7. Glove box 8. Power door lock switches 9.
Page 13 "View B (Vehicles with navigation system) 1. Headlight, turn signal and front fog light switches 2. Cruise control switch 3. Ignition switch 4. Wiper and washer switches 5. Emergency flasher switch 6. Navigation system including air condi- tioning controls (See separate “Navigation System Owner’s Manual”.) 7.
Page 14 "View B (Vehicles without navigation system) 1. Headlight, turn signal and front fog light switches 2. Cruise control switch 3. Ignition switch 4. Wiper and washer switches 5. Emergency flasher switch 6. Clock, outside temperature and trip in- formation display 7.
Page 15 "Lower part of center cluster panel 1. Ashtray 2. Cigarette lighter 3. Power outlet...
Page 16 Instrument cluster overview 11C501b 1. Voltmeter 4. Tachometer 8. Odometer and two trip meters 2. Speedometer 5. Height control indicator light 9. Trip meter reset knob 3. Service reminder indicators and 6. Engine oil pressure gauge 10. Fuel gauge indicator lights 7.
Page 17 Indicator symbols on the instrument panel ∗ 1 Brake system warning light ∗ 1 Tire pressure warning light ∗ 1 ∗ 1 Driver’s seat belt reminder light Unengaged “Park” warning light Automatic transmission fluid temperature warning ∗ 1 Charging system warning light ∗...
Page 18 Automatic transmission indicator lights Vehicle stability control system off indicator ∗ 1 light Vehicle stability control system and active ∗ 1 traction control system warning light Active traction control system indicator light Slip indicator light ∗ 3 Roll sensing of curtain shield airbags off indicator light ∗...
Page 19: Table Of Contents
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobilizer system .
Page 20: Keys
NOTICE of keys. 1. Master keys (black)—These keys work When using a key containing a trans- in every lock. Your Toyota dealer will ponder chip, observe the following need one of them to make a new key precautions: with a built−in transponder chip.
Page 21 z Do not use the key with electromag- netic materials. z When starting the engine, do not z Do not bend the key grip. use the key with other transponder z Do not cover the key grip with any keys around (including keys of oth- material that cuts off electromagnet- er vehicles) and do not press other ic waves.
Page 22: Engine Immobilizer System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on except sponds to the registered ID code for number.
Page 23: Wireless Remote Control
The This device complies with Part 15 of the indicator light will go off. FCC Rules. Operation is subject to the For your Toyota dealer to make a new key following two conditions: with a built−in transponder chip,...
Page 24 The wireless remote control key is an If you lose your wireless remote control electronic component. Observe the follow- key, contact your Toyota dealer as soon ing instructions in order not to cause dam- as possible to avoid the possibility of age and trouble to the key.
Page 25 NOTE: *The 2−step unlocking function can be changed. **The turn signal lights can be set not to flash. Ask your Toyota deal- er for details.
Page 26 The alarm will last for 1 minute. To stop NOTICE: Connect the equipment into an outlet the alarm midway, push the “PANIC”, This equipment has been tested and on a circuit different from that to “LOCK” or “UNLOCK” switch, or unlock found to comply with the limits for a which the receiver is connected.
Page 27 1. Remove the screw, and then the cover. 2. Remove module from z Replace frame. only with same equivalent type recommended by a Toyota dealer. z Dispose of used battery according to the local laws. Replace the battery by following these procedures:...
Page 28: Side Doors
After replacing the battery, check that the neously.* key operates properly. If the key still does NOTE: *The 2−step unlocking function can not operate properly, contact your Toyota be changed. Ask your Toyota dealer for dealer. details.
Page 29 LOCKING UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch down on the front side. To unlock: Push the switch down on the l12093a rear side. All the side doors and back door lock or unlock simultaneously.
Page 30 —Automatic door locking and unlocking functions AUTOMATIC DOOR LOCKING CAUTION You can select the following functions: Locking linked with the shift position Before driving, be sure that the doors closed locked, especially All doors are automatically locked when when small children are in the ve- the selector lever is moved out of “P”...
Page 31 You can set or cancel the automatic To select the locking linked with the AUTOMATIC DOOR UNLOCKING door locking functions: vehicle speed: You can select the following functions: Be sure to apply the parking brake when 1. Close all doors and turn the ignition Unlocking linked with the shift posi- performing the following operations.
Page 32: Power Windows
Power windows You can set or cancel the automatic To select the unlocking linked with the unlocking functions: ignition switch: Be sure to apply the parking brake when 1. Close all doors and turn the ignition performing the following operations. switch to the “ON”...
Page 33 Window lock switch 12C011a l12088a 12C007b Automatic operation: Push the switch Automatic operation: Push the switch OPERATING THE PASSENGERS’ WIN- completely down or pull it completely up, completely down or pull it completely up, DOWS and then release it. The window will fully and then release it.
Page 34 CAUTION Never leave anyone (particularly a small child) alone in your vehicle, To avoid serious personal injury, you especially with the ignition key still must do the following. inserted. Otherwise, could power window Before you close the power win- switches and get trapped in a win- dows, always make sure there is dow.
Page 35: Power Quarter Windows
Power quarter windows Back door CAUTION To avoid serious personal injury, you must do the following. Before you close the power quarter windows, always make sure there is nobody around the power quarter windows. You must also make sure the hands and other parts of the bodies of all occupants are kept completely inside...
Page 36 Pull the handle toward you and pull LOCKING AND UNLOCKING FROM IN- Push the handle and push down the down the lower side of the back door. SIDE lower side of the back door. When closing the back door, make sure To lock: Push the knob.
Page 37 CAUTION CAUTION Keep the back door closed while Before driving, be sure that the back driving. This not only keeps the door is closed and locked, especially luggage from being thrown out but when small children are in the ve- also prevents exhaust gases from hicle.
Page 38: Hood
Hood Theft deterrent system To open the hood: 2. In front of the vehicle, pull up the To deter vehicle theft, the system is auxiliary catch lever and lift designed to sound an alarm if any of 1. Pull the hood lock release lever. The hood.
Page 39 The system will automatically be set after If any of the side door or back door is 30 seconds. When the system is set, the unlocked without the key or wireless re- indicator light will start flashing again. mote control key and the key is not in the ignition switch, all the side doors and 4.
Page 40: Fuel Tank Cap
CAUTION If the system does not work properly, Do not smoke, cause sparks or al- have it checked by your Toyota dealer. low open flames when refueling. The fumes are flammable. When opening the cap, do not re- move the cap quickly. In hot weath-...
Page 41: Electric Moon Roof
CAUTION Make sure the cap is installed se- curely to prevent fuel spillage in the event of an accident. Use only a genuine Toyota fuel tank 12C006b cap for replacement. It is designed to regulate fuel tank pressure. Sliding operation 2.
Page 42 If the moon roof can- rear side. switch. not be operated properly, have it checked by your Toyota dealer. The roof will open and stop partway 30 Jam protection function (closing opera- mm (1.2 in.) from the fully opened posi- tion only): If something gets caught be- tion.
Page 43 CAUTION Never leave anyone (particularly a small child) alone in your vehicle, To avoid serious personal injury, you especially with the ignition key still must do the following. inserted. Otherwise, could use the moon roof switches While the vehicle is moving, always and get trapped in the roof open- keep the heads, hands and other ing.
Page 45 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats ............Front seats .
Page 46: Seats
Front seats— —Front seat precautions Seats While the vehicle is being driven, all ve- Driver seat hicle occupants should have the seatback Slightly recline the back of upright, sit well back in the seat and prop- seat. Although vehicle designs vary, CAUTION many drivers can achieve the 250 erly wear the seat belts provided.
Page 47 —Seat adjustment precautions Front passenger seat Front seats (with SRS side airbags) CAUTION CAUTION CAUTION Do not adjust the seat while the vehicle is moving as the seat may The SRS front passenger airbag The SRS side airbags are installed in unexpectedly move and cause the also deploys...
Page 48 —Adjusting front seats 1. SEAT POSITION AND SEAT CUSHION CAUTION ANGLE ADJUSTING SWITCH Move the control switch in the desired Avoid reclining seatback direction. more than needed. The seat belts pro- Releasing the switch will stop the seat at vide maximum protection in a frontal that position.
Page 49: Armrest
Rear seats— —Rear seat precautions Armrest Tumbling the seats will enlarge the lug- CAUTION gage compartment. See “Cargo and lug- gage” on page 257 for precautions when Do not adjust the seat while the loading luggage. vehicle is moving. Be careful that the seat does not hit a passenger or luggage.
Page 50 —Moving second seat —Adjusting second seats third seat entry SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION Avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the second seat passengers are sitting...
Page 51 —Tumbling second seat CAUTION After returning the seat, make sure the seat is securely locked by push- ing forward and rearward on the top of the seatback and by trying to pull I13378b I13340a up the edge of the bottom cushion. BEFORE TUMBLING SECOND SEAT 2.
Page 52 TUMBLING SECOND SEAT 2. Unlock the seat cushion. Swing the 3. Hook the strap. whole seat up and forward. When returning the second seat to its 1. Lower the outer head restraint to the original position, put the holding strap into lowest position and pull up the cen- the hole.
Page 53 CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 54 —Adjusting third seats —Tumbling third seats SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION I13377b Avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the third seat passengers are sitting up...
Page 55 I13262c 2. Make sure the shoulder belt passes TUMBLING THIRD SEAT 2. Unlock the seat cushion and slide through the hanger when folding the the whole seat the rear−most 1. Lower the head restraint to the low- third seat. position while pulling up the handle. est position.
Page 56 13c558 13c559 13c557a 3. Swing the whole seat up. 4. Hook the strap. 5. Remove the seat hook covers from the back of the seat cushion, and When returning the third seat to its origi- install them over the seat hooks. nal position, put the holding strap into the hole.
Page 57 —Removing third seats CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 58: Head Restraints
Head restraints CAUTION When reinstalling the seat, be care- ful not to hit the seat against you When removing or reinstalling the or inside of the vehicle. seat, observe the following precau- Install each seat in the same posi- tions to prevent personal injury: tion from which it was removed.
Page 59: Seat Heaters
Seat heaters For your safety and comfort, adjust the Right side CAUTION head restraint before driving. front seat To raise: Pull it up. Occupants must use caution when op- To lower: Push it down while pressing the erating the seat heater because it lock release button.
Page 60: Seat Belts
Seat belts— —Seat belt precautions Toyota strongly urges that the driver and Do not allow any children to stand up or NOTICE passengers in the vehicle be properly re- kneel on either rear or front seats. An strained at all times with the seat belts...
Page 61 —Fastening 3−point seat belts CAUTION Be careful not to damage the belt webbing or hardware. Take care that Persons should ride in their seats they do not get caught or pinched properly wearing their seat belts in the seat or doors. whenever vehicle moving.
Page 62 If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from death or serious...
Page 63 CAUTION Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be l13197b kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in a colli- sion.
Page 64 If the seat belt does not function Keep as low on hips as possible normally, immediately contact your Toyota dealer. Do not use the seat Sit up straight and well back in the Remove excess length of the belt and until the seat belt is fixed, because seat.
Page 65 Toyota dealer free of charge. Please contact your local Toyota dealer so that the dealer can order the proper re- quired length for the extender. Bring the heaviest coat you expect to wear for prop- er measurement and selection of length.
Page 66 Make sure the front passenger oc- Do not use the seat belt extender cupant classification indicator light when installing child restraint indicates “ON” when using the seat system on the front or rear passen- belt extender for the front passen- ger seat.
Page 67 If the seat belt does not function normally, immediately contact your The driver and front passenger seat belt Toyota dealer. Do not use the seat pretensioners are designed to be acti- until the seat belt is fixed, because vated in response to a severe frontal...
Page 68 The front passenger’s seat belt pretension- er will not activate if no passenger is CAUTION detected in the front passenger seat by Make sure the roll sensing of cur- the front passenger occupant classification system. However, the front passenger’s tain shield airbags indicator...
Page 69 Failure to follow these instructions switch able the system, which could result can result in death or serious inju- in death or serious injury. 5. Seat belt pretensioner assemblies ries. Consult your Toyota dealer about any repair and modification. 6. Airbag sensor assembly...
Page 70 Do not perform any of the following assemblies, curtain shield airbag sensor changes without consulting your assemblies, driver’s seat position sensor, Toyota dealer. Such changes driver’s seat belt buckle switch, front pas- interfere with proper operation of the senger occupant classification system and...
Page 71: Srs Airbags
In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- dealer as soon as possible: tem) front airbags are designed to pro-...
Page 72 The driver and front passenger can child restraint system. Toyota The SRS front passenger airbag will not be killed or seriously injured by the strongly recommends that all in- activate if there is no passenger sitting in inflating airbags if they do not wear fants and children be placed in the the front passenger seat.
Page 73 The SRS front airbags are designed to deploy in severe (usually frontal) colli- sions where the magnitude and duration of the forward deceleration of the ve- Hitting a curb, Falling into or hicle exceeds the designed threshold edge of pavement jumping over a Collision from the rear level.
Page 74 8. Driver’s seat position sensor Deployment of the airbags happens in a fraction of a second, so the airbags must 9. Airbag sensor assembly inflate with considerable force. While the 10. Airbag module for driver system is designed to reduce serious inju- (airbag and inflator) ries, primarily to the head and chest, it The airbag sensor assembly consists of a...
Page 75 SRS driver’s air- can be killed or seriously injured. bag system will judge that the driv- Toyota strongly recommends that: er wears the seat belt even if not wearing it. In this case, the driver’s The driver sit as far back as pos-...
Page 76 “Child should not hold objects in their serious injury. restraint” on page 83. arms or on their knees. Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification.
Page 77 Toyota dealer. It may assemblies, curtain shield airbag sensor dangerously interfere with the SRS assemblies, driver’s seat position sensor, front airbags operation.
Page 78 The SRS side airbag on the passenger seat will not activate if there is no pas- In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- senger sitting in the front passenger seat. dealer as soon as possible:...
Page 79 To ensure maximum protection child restraint system. Toyota in an accident, the driver and all strongly recommends that all in- passengers vehicle must fants and children be placed in the...
Page 80 When you push the roll sensing of curtain shield airbags off switch for a few sec- CAUTION onds with the ignition switch on, the roll Make sure the roll sensing of cur- sensing of curtain shield airbags off indi- cator light comes on and the roll sensing tain shield airbags...
Page 81 Collision from the rear Collision from the front The angle of Skidding vehicle vehicle tip−up hitting a curb Vehicle rollover is marginal stone The SRS side airbag and curtain shield The SRS side airbags are not generally The curtain shield airbags may inflate airbag system may not activate if the designed to inflate if the vehicle is in- if the angle of vehicle tip−up is margin-...
Page 82 Collision from Falling into or jump- Hitting a curb, edge of Collision from 13c538d the front ing over a deep hole pavement or hard sur- the rear face Pitch end over end Landing hard or vehicle falling The SRS side airbag and curtain shield The curtain shield airbags are not gen- The SRS side airbags and curtain shield airbag system consists mainly of the fol-...
Page 83 7. Curtain shield airbag sensors When the airbags inflate, they produce a fairly loud noise and release some smoke CAUTION 8. Side and curtain shield airbag sensors and residue along with non−toxic gas. This 9. Airbag sensor assembly SRS side airbags and curtain shield does not indicate a fire.
Page 84 Sit up straight and well back in the seat, distributing your weight evenly in the seat. Do not apply excessive weight to the outer side of the seats with a side airbag and to the front and rear pillar, front, center 13c562 and rear garnish and roof interior with the curtain shield airbag.
Page 85 Do not allow anyone to kneel on the passenger seat, facing the pas- senger’s side door, since the side airbag and curtain shield airbag could inflate with considerable speed and force. Otherwise, he/she may be killed or seriously injured. 13c563 Special care should be taken espe- cially when you have a small child in the vehicle.
Page 86 Do not hook a hanger, heavy or sharp pointed objects on the coat hook. If the curtain shield airbags inflate, those items will be thrown away with great force or the curtain shield airbags may not activate cor- 13c800b rectly, resulting in death or serious injury.
Page 87 Such changes may disable curtain shield airbags to inflate ac- Toyota dealer. Such changes can in- the system or cause the curtain cidentally, resulting in death or seri- terfere with proper operation of the shield airbags to inflate accidental- ous injury.
Page 88 It goes off after about 6 seconds. This or seat belt pretensioners. Contact your means the SRS side airbags and curtain Toyota dealer as soon as possible. shield airbags are operating properly. The light does not come on when the ignition key is turned to the “ON”...
Page 89 —Front passenger occupant classification system In the following cases, contact your Toyota Your vehicle is equipped with a front dealer as soon as possible: passenger occupant classification sys- tem. This system detects the conditions Any of the SRS side airbags and cur- 1.
Page 90 If the front passenger occupant classifica- Make sure that the “ON” indicator is illu- tion system determines that a person of minated when an adult is seated in the adult size sits in the front passenger seat front passenger seat. If the “OFF” indica- but the “OFF”...
Page 91 Condition and operation in the front passenger occupant classification system Indicator/ warning light Devices Condition detected by Curtain shield Front passenger Front Side airbag on Front the front passenger Front airbag in the SRS warning occupant passenger’s the front passenger’s occupant classification front passenger...
Page 92 CAUTION Do not recline the front passenger Wear the seat belt properly. seatback so far that it touches a Make sure the front passenger’s To avoid potential death or serious rear seat. This cause seat belt tab has not been left in- injury when the front passenger occu- “OFF”...
Page 93: Child Restraint
Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- When it is unavoidable to install the Toyota strongly urges use of propriate child restraint systems for forward−facing child restraint sys- proper child restraint system which children. tem on the front passenger seat, conforms to the size of the child, The laws of all 50 states in the U.S.A.
Page 94 —Child restraint system A child restraint system for a small A forward−facing child restraint sys- Do not use the seat belt extender child or baby must itself be properly should allowed when installing child restraint restrained on the seat with the lap por- installed on front passenger system on the front or rear passen-...
Page 95 —Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.
Page 96 —Installation with 2−point type seat belt 1. Run the center lap belt through or (A) INFANT SEAT INSTALLATION CAUTION around the infant seat following the An infant seat must be used in rear− instructions provided by its manufactur- facing position only. Do not install a child restraint sys- er and insert the tab into the buckle tem on the third seat if it interferes...
Page 97 2. While pressing the infant seat firmly Contact your Toyota dealer CAUTION against the seat cushion and seatback, immediately. Do not install the child tighten the lap belt by pulling its free...
Page 98 3. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle release button. A convertible seat must be used in for- ward−facing or rear−facing position de- Do not install a child restraint sys- pending on the age and size of the tem on the third seat if it interferes child.
Page 99 1. Run the center lap belt through or 2. While pressing convertible seat Contact your Toyota dealer around the convertible seat following firmly against the seat cushion and immediately. Do not install the child instructions provided...
Page 100 —Installation with 3−point type seat belt 13c564 3. To remove the convertible seat, press (A) INFANT SEAT INSTALLATION CAUTION the buckle release button. An infant seat must be used in rear− facing position only. Push and pull the child restraint sys- tem in different directions to be sure it is secure.
Page 101 Child restraint systems installed on the third seat should not contact the second seatbacks. 13c565 CAUTION Do not install a child restraint sys- tem on the second (or third) seat if Never install a rear−facing child re- it interferes with the lock mecha- straint system on the front passen- nism of the front (or second) seats.
Page 102 1. Run the lap and shoulder belt through 2. Fully extend the shoulder belt to put it Contact your Toyota dealer or around the infant seat following the in the lock mode. When the belt is immediately. Do not install the child...
Page 103 3. While pressing the infant seat firmly 4. To remove the infant seat, press the CAUTION against the seat cushion and seatback, buckle release button and allow the let the shoulder belt retract as far as belt to retract completely. The belt will Push and pull the child restraint sys- it will go to hold the infant seat secure- move freely again and be ready to...
Page 104 Install the child restraint system on the 6. While pressing convertible seat front passenger seat only when it is un- firmly against the seat cushion and avoidable. Your vehicle is equipped with a seatback, let the shoulder belt retract front passenger occupant classification...
Page 105 Remove the child restraint ence of the child restraint system and the front passenger airbag and side system and contact your Toyota dealer. Never install a rear−facing child re- airbag on the front passenger seat straint system on the front passen- could deploy.
Page 106 On vehicle with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar, front, center or rear 13c568 13c501b garnish or roof interior from which...
Page 107 1. Run the lap and shoulder belt through Contact your Toyota dealer or around the convertible seat following immediately. Do not install the child instructions provided restraint system on the seat until manufacturer and insert the tab into the seat belt is fixed.
Page 108 2. Fully extend the shoulder belt to put it 3. While pressing convertible seat CAUTION in the lock mode. When the belt is firmly against the seat cushion and then retracted even slightly, it cannot seatback, let the shoulder belt retract Push and pull the child restraint sys- be extended.
Page 109 13c569 13c570 Move seat fully back 4. To remove the convertible seat, press (C) BOOSTER SEAT INSTALLATION CAUTION the buckle release button and allow the A booster seat must be used in for- belt to retract completely. The belt will ward−facing position only.
Page 110 On vehicle with side airbags and CAUTION curtain shield airbags, do not allow the child to lean his/her head or Always make sure the shoulder belt any part of his/her body against the is positioned across the center of door or the area of the seat, front child’s shoulder.
Page 111 Contact your Toyota dealer immediately. Do not install the child restraint system on the seat until 13C001 the seat belt is fixed. 2. To remove the booster seat, press the...
Page 112 Symbol 13C003 13C004 Anchor brackets Use the anchor bracket located behind the TO USE THE ANCHOR BRACKET: 2. Fix the child restraint system with second seat on the floor to attach the top the seat belt. 1. Remove the head restraint. strap.
Page 113 —Installation with child restraint lower anchorages 13C005 13c571 13C529 Most upright position 4. Replace the head restraint. The lower anchorages for the child re- CHILD RESTRAINT SYSTEM INSTALLA- TION straint system interfaced with FMVSS225 specification are installed in 1. Fold down the seatback and back to the second seat.
Page 114 3. Type A—Latch the hooks of lower straps onto anchorages tighten the lower straps. Type B—Latch the buckles onto the anchorages If your child restraint system has a top 13C532f 13C009b strap, it should be anchored. (For the installation of the top strap, see “—Using a top strap”...
Page 115 CAUTION When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught. Push and pull the child restraint system in different directions to be sure it is secure.
Page 117 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Power tilt and telescopic steering wheel ..... . . Outside rear view mirrors .
Page 118: Power Tilt And Telescopic Steering Wheel
This feature can be set inoperative. Ask ries. your Toyota dealer.
Page 119: Outside Rear View Mirrors
—Power rear view mirror control Outside rear view mirrors— CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.
Page 120: Anti−Glare Inside Rear View Mirror
Anti−glare inside rear view mirror— —Folding rear view mirrors NOTICE If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror. 13C010b The rear view mirrors can be folded Adjust the mirror so that you can just backward for parking in compact areas.
Page 121 —Compass (vehicles without navigation system) When the ignition key is inserted and turned on, the inside rear view mirror al- ways turns on in the “AUTO” mode. When the inside air temperature is low, it may take a little longer for the mirror to darken in response to the detection of 13c570b headlights.
Page 122 Pushing the “AUTO” button for longer NOTICE than 3 seconds turns on or off the compass display. Do not put magnets or a metal object The compass may not show the correct near the inside rear view mirror. Do- direction in the following conditions: ing this may cause malfunction of the compass sensor.
Page 123 If the direction is displayed several sec- onds after adjustment, the calibration is finished. CAUTION Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped. 13C015b L Hawaii is included in zone 6. Zone number...
Page 124 Do not adjust the display while the If calibration cannot be performed because vehicle is moving. Be sure to adjust of the magnetized vehicle, etc., take your the display only when the vehicle is vehicle to Toyota dealer. stopped.
Page 125: Sun Visors
Sun visors— —Vanity mirror To block the glare from the front when the To block out glare, move the sun visor. To use the vanity mirror, swing down main sun visor is swung down, swing the main sun visor and open the cover. To block out glare from the front—Swing down the second sun visor.
Page 127 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlight and turn signals ........Emergency flashers .
Page 128: Headlight And Turn Signals
NOTE: *The operating condition or sensi- tivity can be changed. Ask your Toyota dealer for details. The automatic light control sensor is on HEADLIGHTS the top of the passenger’s side instrument...
Page 129 “LOCK” but- ton on the wireless remote control key turns off the headlights. NOTE: *The time before turning off the lights can be changed. Ask your Toyota dealer for details. NOTICE To prevent the battery from being dis-...
Page 130: Emergency Flashers
Emergency flashers Instrument panel light control NOTICE To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running. To turn on the emergency flashers, To adjust the brightness of the instru- push the switch.
Page 131: Front Fog Lights
Front fog lights Interior lights To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”— —Center: Turn the light on when any of side doors and back door are opened.
Page 132: Personal Lights
One front door will be closed with the lock knob pushed forward while the other doors are locked. NOTE: *The interior lights can be set not to come on or the duration of lighting can be changed. Ask your Toyota dealer for details. Center...
Page 133: Ignition Switch Light
Ignition switch light Windshield wipers and washer To turn on the personal light, push the switch on side 1. To turn the lights off, push the switch on side 2. PERSONAL LIGHTS CUT OFF OPERA- TION When the ignition switch is “OFF” and any personal lights in the vehicle stay lighting on, the lights will cut off automatically after 30 minutes.
Page 134: Rear Window Wiper And Washer
To squirt washer fluid on the rear window, blocked. If a nozzle becomes blocked, twist the knob upward or downward as far contact your Toyota dealer to have the as it will go (position 3 or 4). The knob vehicle serviced.
Page 135: Rear Window Defogger
Rear window defogger Outside rear view mirror heaters Make sure you turn the defogger off when the surfaces are clear. Leaving the defog- ger on for a long time could cause the battery discharge, especially during stop−and−go driving. The defogger is not designed for drying rain water or for melt- ing snow.
Page 136 CAUTION Since the mirror surfaces can get hot, do not touch them when the mirror heater switch is on. Make sure you turn the mirror heaters off when the surfaces are clear. Leaving the mirror heaters on for a long time could cause the battery to discharge, especially during stop−and−go driving.
Page 137 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge ..........Engine coolant temperature gauge .
Page 138: Fuel Gauge
Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. 15C004 The gauge indicates the approximate...
Page 139: Engine Oil Pressure Gauge
If the engine oil pressure should stay be- low the normal range, pull off the road to a safe place and stop the engine immedi- ately. Call a Toyota dealer or qualified repair shop for assistance. Engine oil pressure may not build up when the engine oil level is too low.
Page 140: Voltmeter
Voltmeter Tachometer NOTICE Do not let the indicator needle get into the red zone. This may cause severe engine damage. The voltmeter tells whether the battery The tachometer indicates engine speed is charged discharged. Check in thousands of rpm (revolutions per while the engine is running—the needle minute).
Page 141: Odometer And Two Trip Meters
Odometer and two trip meters 3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push.
Page 142: Service Reminder Indicators And Warning Buzzers
Service reminder indicators and warning buzzers If the indicator or buzzer comes on... Do this. If parking brake is off, stop immediately and contact Toyota dealer. (indicators and buzzer) Fasten driver’s seat belt. (indicators and buzzer) Fasten front passenger’s seat belt.
Page 143 If the indicator or buzzer comes on... Do this. Take vehicle to Toyota dealer immediately. Take vehicle to Toyota dealer. If brake system warning light is also on, stop immedi- ately and contact Toyota dealer. Close all side doors and back door.
Page 144 It is dangerous to continue driving Depressing the brake pedal repeatedly a safe place and contact your Toyota normally when the brake fluid level is may turn on the warning light and dealer.
Page 145 Once the ignition key is turned to “ON” or safe place and contact your Toyota “START”, the reminder light flashes if a You need to reset the light after the en- dealer.
Page 146 Have your vehicle the tank as soon as possible. after taking several driving trips. checked by your Toyota dealer as soon as If the lamp will not go off even after sev- possible. eral trips, contact your Toyota dealer as Even if the abnormality of the electronic soon as possible.
Page 147 Contact your It goes off after about 6 seconds. This pant classification system. Toyota dealer as soon as possible to means the SRS airbags and seat belt service the vehicle. pretensioners are operating properly.
Page 148 Although it is no problem to continue If the light does not go off, call a Toyota (j) Open Door Warning Light driving, have your vehicle checked by...
Page 149 OFF” indicator light come on, have your the key when you open the driver’s door 5. Turn the ignition key to “ON”, but do vehicle checked by Toyota dealer as soon with the ignition key in the “ACC” or not start the engine.
Page 150: Trip Information Display
Trip information display (vehicles without navigation system) The following information is shown with Average vehicle speed Driving distance after engine starting the ignition key turned on. Each time The average vehicle speed is calculated The driving distance after engine start- you push the “MODE”...
Page 151 Available driving range Average fuel consumption after re- Current fuel consumption fueling The available driving range is calcu- The current fuel consumption is calcu- lated and displayed depending on the The average fuel consumption after re- lated and displayed based on the driv- amount of remaining fuel.
Page 153 ..........Active height control suspension (AHC) ..... . . Skyhook TEMS (Skyhook Toyota electronic modulated suspension)
Page 154: Ignition Switch
Ignition switch Approximately five hours after the engine “ACC”—Accessories such as the radio is turned off, you may hear a sound com- operate, but the engine is off. ing from underneath the luggage compart- If you leave the key in the “ACC” or ment for several minutes.
Page 155: Automatic Transmission
Automatic transmission Selector lever position P: Parking, engine starting and key removal position R: Reverse position N: Neutral position D: Normal driving position (Shifting into overdrive position) 4: Position for engine braking (Shifting into overdrive not possible) 3,2: Position for more powerful engine braking L: Position for maximum engine braking "...
Page 156 Your automatic transmission has a shift 3. Release the parking brake and brake Shift into the “L” position. The trans- lock system to minimize the possibility of pedal. Depress the accelerator pedal mission will downshift to first gear incorrect operation. This means you can slowly for smooth starting.
Page 157 (c) Using “3”, “2” and “L” positions (d) Backing up NOTICE The “3”, “2” and “L” positions are used for 1. Bring the vehicle to a complete stop. z Be careful not to over-rev the en- strong engine braking as described pre- 2.
Page 158 If the four–wheel drive control is in the When towing a trailer, in order to main- For ordinary driving, Toyota recommends “N” position while the selector lever is in tain engine braking efficiency, do not using the Normal mode to improve fuel the “P”...
Page 159: Four-Wheel Drive System
Four–wheel drive system— (a) Four–wheel drive contro l Use the center differential lock system if (i) If you cannot shift the selector le- your wheels get stuck in a ditch, or when ver out of “P” position you are driving on a slippery or bumpy If you cannot shift the selector lever from surface.
Page 160 In this mode, the braking feeling that oc- The center differential lock system opera- “H” (high speed position, center differ- ential unlocked): Lever at “H”, center dif- curs when the wheels are negotiating a tion is not completed within 5 seconds ferential lock button left out sharp corner is further reduced than in the while the cruise control system is set,...
Page 161 (b) Shifting procedure Use the “L” position of the automatic SHIFTING BETWEEN “H” (UNLOCKED) NOTICE transmission lever for maximum power AND “H” (LOCKED) and traction when your wheels get stuck For normal driving on dry and hard shift between unlock lock or when you drive down a steep incline.
Page 162: Active Traction Control System
If the “VSC/TRAC” warning light comes controlling the output of the brake and on, have your vehicle checked by your engine. Thus, the system assists driver Toyota dealer as soon as possible. control driving power wheels. When you turn the ignition...
Page 163 (The continuous buzzer sounds for about In the following cases, contact your Toyota your vehicle should be fitted with snow tires or tire chains. Always 3 seconds.) At the time, the “VSC/TRAC”...
Page 164: Vehicle Stability Control System
When replacing the tires or wheels, The vehicle stability control system is acti- substitute for safe driving practices. contact your Toyota dealer. (See vated when the vehicle speed is about Factors including speed, road con- “Checking and replacing tires” on more than 15 km/h (9 mph).
Page 165 If the “VSC/TRAC” warning light and “VSC OFF” indicator light come on, have your vehicle checked by your Toyota dealer as soon as possible. However, there is no problem if the “VSC/TRAC” warning light comes on when the brake actuator tem- perature becomes high.
Page 166: Tire Pressure Warning System
If the continue to drive. tire inflation pressure becomes low, the In the following cases, contact your Toyota light comes on again. In this case, adjust- dealer: ing the tire inflation pressure will turn off The “VSC/TRAC”...
Page 167 The tire pressure warning that you have a flat tire. Check the light will turn off after a few minutes. tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota deal-...
Page 168 As an added safety feature, your ve- Your vehicle has also been equipped TPMS (tire pressure warning system) hicle has been equipped with a tire with a TPMS (tire pressure warning malfunction may occur for a variety pressure monitoring system (TPMS– system) malfunction indicator to indi- of reasons, including the installation tire pressure warning system) that il-...
Page 169 If a radio set at similar frequencies is replaced, have them repaired or re- in use in the vehicle. placed by the nearest Toyota dealer or an authorized tire dealer. The If a window tint that affects the radio tire pressure warning valves and wave signals is installed.
Page 170 Even if you use genuine wheels, the tire This device complies with Part 15 of the Reorient or relocate the receiving an- pressure warning system may not work FCC Rules. Operation is subject to the tenna. properly with some types of tires. following two conditions: Increase the separation between the Pushing the tire pressure warning reset...
Page 171 ID code of tire pres- sure warning valve and transmitter. Have the ID code registered by your Toyota dealer. If the ID code is not registered, the sys- tem will not work properly. After about 1...
Page 172 If initialization not performed. cannot be performed, have the system checked at your Toyota dealer. If you push the tire pressure reset switch accidentally and initialization is performed, adjust the tire inflation pressure to the specified level and initialize the system...
Page 173: Parking Brake
16C524a When you replace a new set of tires, purchase tire pressure warning valves and transmitters from your Toyota dealer and have the new ID code registered by your Toyota dealer. If the tire pressure select switch is set to the wrong tire setting, the system will not work properly.
Page 174: Cruise Control
Cruise control The cruise control is designed to main- CAUTION CAUTION tain a set cruising speed without requir- ing the driver to operate the accelera- Before driving, be sure the parking To help maintain maximum control tor. Cruising speed can be set to any brake is fully released and the park- of your vehicle, do not use the speed above 40 km/h (25 mph).
Page 175 CAUTION To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the “CRUISE” indicator light is off. TURNING THE SYSTEM ON AND OFF SETTING THE CRUISING SPEED To turn the cruise control on, press the The transmission must be in “D”...
Page 176 Toyota deal- control lever down in the “– SET” direc- itself under certain circumstances. Tempo- er at the earliest opportunity.
Page 177: Active Height Control Suspension (Ahc)
The indicator light goes out after it (a) Vehicle height modes comes on. “HI” (high) mode— If this is the case, contact your Toyota The vehicle height is about 40 mm (1.6 dealer and have your vehicle inspected. in.) higher at front and about 50 mm (2.0 in.) higher at rear than the normal...
Page 178 When the vehicle exceeds the specified Extra high mode— “N” (normal) mode— vehicle speed, vehicle height This mode automatically selected The vehicle height in this mode is stan- changes to the following: from the high mode with the four−wheel dard. With the four−wheel drive control lever drive control lever placed in “L”...
Page 179 (b) Automatic leveling function (c) Vehicle height mode changing In the following cases the active height condition control suspension does not operate Regardless of the number of occupants even if the above conditions are all To change the vehicle height, it is nec- or the luggage loading condition, the met.
Page 180 The vehicle height cannot be raised if NOTICE the vehicle load exceeds the following limits: z If you change the vehicle height fre- ∗ Up to 4 occupants plus about 280 kg quently, the pump may overheat. To (617 lb.) in the normal mode prevent this, the active height con- trol suspension should be stopped ∗...
Page 181 Selecting the high mode— NOTICE Push the height select switch on the “ ” Do not select the low mode in the side when the vehicle speed is under bumpy roads. If the underbody of the about 30 km/h (19 mph). vehicle touches the rugged road sur- To change the normal mode to high, face, the vehicle may be damaged.
Page 182 z If your vehicle gets ditched, turn off CAUTION the active height control suspension with height control switch. If you drive through deep water over Otherwise, the vehicle height may about 500 mm (20 in.) in depth, put change because of the automatic the vehicle height in the HI (High) leveling function, resulting in an ac- mode with the active height select...
Page 183 With the active height control suspen- If the vehicle is loaded heavily, the ve- sion turned off, if you operate the hicle height cannot be raised even if height select switch the vehicle the height select switch is operated. If height is changing depending on the underbody vehicle...
Page 184 Toyota dealer as soon as possible. tact with the underbody of the vehicle. ing limits. The vehicle changes to the se- The height control “OFF”...
Page 185: Skyhook Tems (Skyhook Toyota Electronic Modulated Suspension)
“OFF” indicator blinks again, bring your mode select switch to provide good rid- vehicle to your Toyota dealer as soon as ing comfort and stability. possible and have it checked. 1. For driving on a bumpy road 2.
Page 187 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference ..........Using your audio system .
Page 188: Audio System
—some basics Reference This section describes some of the basic SWITCHING BETWEEN FUNCTIONS features on Toyota audio systems. Some Push “AM·SAT”, “FM”, “TAPE” or “DISC” information may not pertain to your sys- if the system is already on but you want tem.
Page 189 Satellite tuner technology notice: TONE AND BALANCE You must enter into a separate service Toyota’s satellite radio tuners are awarded For details about your system’s tone and agreement with the XMr radio in order to Type Approval Certificates from XMr Sat-...
Page 190 For the installation performed during antenna extension. The of the window tint, consult with maximum extension length is 850 mm your Toyota dealer. (33.5 in.). Every time you turn the radio on, the antenna will extend to its previous posi- tion.
Page 191 YOUR COMPACT DISC PLAYER CAUTION When you insert a disc, gently push it in with the label side up. Before extending the antenna, confirm The discs set in the player are played that no one is close enough to get continuously, starting with disc number 1.
Page 192 —Controls and features Details of specific buttons, controls, and features are described in the alphabetical list that follows. 17c517d...
Page 193 The button number will appear on the *: Use of satellite radio requires XMr tuner the discs will be automatically cancelled. display. and service. Contact your Toyota dealer for details. To tune in to a preset station: Push the (Program) button for the station you want.
Page 194 “AM” to switch from cassette or compact display. *: Use of satellite radio requires XMr tuner disc operation to radio operation. To stop the tape while it is fast forward- and service. Contact your Toyota dealer AUDIO−TUNE Knob ing, push fast...
Page 195 If the malfunction is not rectified, take loading multiple compact discs. After your vehicle to your Toyota dealer. FM button pushing the button, insert a compact disc. Push “FM” to turn on the radio and select At this time, the indicators on both sides DISC the FM band.
Page 196 Loading multiple compact discs— RAND (Random) RDS (Radio Data System) display To load multiple compact discs, push and There are two random features—you can The radio will automatically switch to the hold (until you hear a beep when the au- either listen to the tracks on all the com- RDS mode to receive an RDS station dio system is on).
Page 197 See a another channel. disc you are listening to. When the disc Toyota certified dealer. “– – –”: The channel you selected is no ends, the player will automatically go back longer available. Wait for about 2 seconds “UPDATING”:...
Page 198 *: Use of satellite radio requires XMr tuner XMr satellite radio*— Compact Disc Player and service. Contact your Toyota dealer You can either scan the currently selected There are two scan features—you can ei- for details. channel category or scan only the preset ther scan the tracks on a specific disc or channels for that band.
Page 199 *: Use of satellite radio requires XMr tuner After the beginning of the tape is the amount of channel separation to prev- and service. Contact your Toyota dealer reached, the player will automatically ent the weak signal from creating noise.
Page 200 : Use of satellite radio requires XMr If the entire disc or track title does not tuner and service. Contact your Toyota appear on the display, push and hold the If the entire the message is not displayed, dealer for details.
Page 201: Audio System Operating Hints
*: Use of satellite radio requires XMr tuner RADIO RECEPTION Each time you push the “ ” or “ ”, the and service. Contact your Toyota dealer Usually, a problem with radio reception program type changes as in the following: for details.
Page 202 *: Use of satellite radio requires XMr tuner ened, and there is another strong station and service. Contact your Toyota dealer nearby on the FM band, your radio may for details. tune in the second station until the origi-...
Page 203 Avoid using cassettes with a total play- CARING FOR YOUR CASSETTE PLAYER If this equipment does cause harmful ing time longer than 100 minutes (50 AND TAPES interference to radio or television re- minutes per side). The tape used in For the best performance for your cas- ception, which can be determined by these cassettes is thin and could get...
Page 204 CARING FOR YOUR COMPACT DISC PLAYER AND DISCS The player is intended for use with 12 cm (4.7 in.) discs only. Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.
Page 205 NOTICE z Do not use special shaped, trans- parent/translucent, low quality or la- beled discs such as those shown in the illustrations. The use of such discs may damage the player or changer, or it may be impossible to eject the disc. z This system is not designed for use Correct Wrong...
Page 206: Rear Seat Audio System
Rear seat audio system (b) When the radio mode is selected ” button: Push this button to “ select a preset station on the preset but- ton of the front audio system. Each push of the button changes to the station with higher numbered preset button.
Page 207: Audio Remote Controls (Steering Switches)
Audio remote controls (steering switches) (c) When the “TAPE” mode is selected (e) Some basics ” button: Push this button This system cannot be used if the audio “ PROG system is not turned on. to select the other side of a cassette tape.
Page 208 XMr satellite radio*— To select a preset channel, push the “ ” or “ ” side of the switch. Repeat until a desired channel is found. *: Use of satellite radio requires XMr tuner and service. Contact your Toyota dealer for details.
Page 209: For Vehicle Equipped With Navigation System, Please Refer To The Separate "Navigation System Owner's Manual
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Front air conditioning system: Controls ..........Air flow selector settings .
Page 210: Front Air Conditioning System: Controls
Front air conditioning system— —Controls 1. Temperature selector knob 2. “AUTO” button 3. Temperature display 4. Fan speed display 5. Air flow display 6. “MODE” button 7. “A/C” button 8. Windshield air flow button 9. Fan speed control button 10. Air intake control button 11.
Page 211 “MAX COLD” appears when you adjust to “AUTO” button maximum cooling, and “MAX HOT” ap- For automatic operation of the air condi- pears when you adjust to maximum warm- tioning, press the “AUTO” button. An indi- ing. cator light will illuminate to show that the automatic operation mode has been se- “OFF”...
Page 212 flows mainly When the “A/C” button is not pressed in, 4. Floor/Windshield—Air from the floor vents and windshield pressing “MODE” button turns off the air vents. conditioning. It is recommended that you close the For details about air flow selector setting, lower vent.
Page 213 If this happens, take your ve- hicle to a Toyota dealer for service. Air intake control button Press the button to select the air source. An indicator light will illuminate to show which air intake mode is being selected.
Page 214: Air Flow Selector Settings
—Air flow selector settings —Operating tips To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
Page 215 If following another vehicle on a dusty Heating Air conditioning road, or driving in windy and dusty For best results, set controls to: For best results, set controls to: conditions, it is recommended that the air intake control button be temporarily Fan speed—“AUTO”...
Page 216: Instrument Panel Vents
—Instrument panel vents Defogging Defrosting The inside of the windshield The outside of the windshield For best results, set controls to: For best results, set controls to: Temperature— Towards high temperature Temperature—Towards high temperature to heat; Air intake—FRESH (outside air) low temperature to cool Air flow—WINDSHIELD Air intake—FRESH (outside air)
Page 217 Lower vent If air flow control is not satisfactory, check the instrument panel vents. The instrument panel vents may be opened or closed as shown. For removing frost or fog, it is recom- mended that you close the lower vent when you use the “Floor”, the “Floor/Wind- shield”...
Page 218: Rear Air Conditioning System
Rear air conditioning system— —Controls 1. Rear air conditioning on−off switch 2. “AUTO” button 3. Air flow selector 4. Fan speed selector 5. Temperature selector 6. “OFF” button 18c507b...
Page 219 Rear air conditioning on−off switch Temperature selector To turn the rear air conditioning on, press Move the lever to adjust the tempera- the “REAR” switch. To turn the rear air ture—to the right to warm, to the left to conditioning off, press the switch again. cool.
Page 220: Air Flow Selector Settings
—Air flow selector settings 18c508a Warm air Cool air...
Page 221 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock ............Outside temperature display .
Page 222: Clock
Clock Outside temperature display To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The key must be in the “ACC” or “ON” position. If quick adjustment to a full hour is de- sired, push the “:00” button. 18C510 18C511 For example, if the “:00”...
Page 223: Rear View Monitor System
Rear view monitor system The display indicates between the range The rear view monitor system assists of –22°F and 122°F. CAUTION the driver by displaying an image of the view behind the vehicle while back- The key must be in the “ON” position. Never depend on rear...
Page 224 When replacing the tires, please consult If the back of the vehicle is hit, the your Toyota dealer. If you replace the position and mounting angle of the tires, the area displayed on the screen camera may change. Be sure to may change.
Page 225 When water droplets are adhering to AREA DISPLAYED ON SCREEN the camera, or when humidity is high Image is displayed approximately level (for example, when it rains) on screen. When foreign matter (for example, The area detected by the camera is snow or mud) adheres to the camera limited.
Page 226: Cigarette Lighter And Ashtray
Do not hold the cigarette lighter pressed mitted by the camera, the light source appears to have a vertical streak above and below it. Use a Toyota genuine cigarette lighter or equivalent for replacement.
Page 227: Power Outlets
Power outlets The power outlets are designed for power supply for car accessories. To use them, open the lids as shown in the following illustrations. The key must be in the “ACC” or “ON” position to be used. NOTICE z To prevent the fuse from being blown, do not use the electricity over the total vehicle capacity of...
Page 228: Roll Sensing Of Curtain Shield Airbags Off Switch
Roll sensing of curtain shield airbags off switch In a severe side impact, the curtain shield airbags on impacted side will inflate even CAUTION if the roll sensing function is turned off. Make sure the roll sensing of cur- If the ignition switch is turned to “ACC” or tain shield airbags off indicator light “LOCK”...
Page 229: Rear Console Box
Rear console box Glove box Garage door opener Buttons Indicator light The garage door opener (HomeLink To use the rear console box, open as To use the glove box, do this. Universal Transceiver) is manufactured un- shown in the illustration. To open: Pull the lever.
Page 230 The battery side of the hand−held trans- mitter must be pointed away from the HomeLink during the programming pro- HomeLink cess. For Canadian users, follow the procedure in “Programming an entrance gate/Pro- 19C514 19C515 gramming all devices in the Canadian 25 to 75 mm market”.
Page 231 6. Repeat steps 2 through 5 for each re- 1. Locate the “training” button on the ceil- maining HomeLink button to program ing mounted garage door opener motor. another device. The exact location and color of the button may vary by brand of garage Programming a rolling code system door opener.
Page 232 Canadian market To program other devices such as home 1. Decide which of the 3 HomeLink but- security systems, home door locks or tons you want to program. lighting, contact your authorized Toyota dealer for assistance. 2. Place your hand−held gate/device 19C517 transmitter 25 to 75 mm (1 to 3 in.)
Page 233 FCC Rules and with RSS−210 of the IC ceiver call the: Rules. Operation is subject to the fol- When programming the HomeLink Toyota Customer Experience Center at lowing two conditions: (1) This device Universal Transceiver, you may be 1−800−331−4331 (U.S.A.)
Page 234: Auxiliary Boxes
Auxiliary boxes— To use the auxiliary boxes, open as shown in the following illustrations. CAUTION To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving. Type A (luggage compartment) Type C (rear console) Type B (luggage compartment)
Page 235: Cup Holders
—First−aid kit holder —Warning reflector holder Cup holders The cup holder is designed for holding cups or drink−cans securely. To use them, observe the following illustra- tions. CAUTION Do not place anything else other than cups or drink−cans in the cup holder, such items...
Page 236 19C008 For front seats For front seat For second seats The cup holder can be adjusted to the To use a cup holder in the console box. size of cups by changing the separator 1. Open the console box lid. Pull down position or moving the separator arms.
Page 237: Card Holder
Card holder Tie−down hooks For third seats (left−hand side) You can store a card in the slot as To secure your luggage, use the tie− shown in the illustration. down hooks as shown above. See “Cargo and luggage” on page 257 for precautions when loading luggage.
Page 238: Cargo Net Hooks
Cargo net hooks Roof luggage carrier Side Cross knobs rails Upper knob Roof rails These hooks are designed to hang car- The roof luggage carrier consists of ADJUSTING THE POSITION OF CROSS go net. roof rails and sliding cross rails. RAILS: To hang the cargo net, use the cargo net 1.
Page 239 Follow the manufacturer’s instructions and precautions when installing the attach- ments or their equivalent. CAUTION When you load cargo on the roof lug- gage carrier, observe the following: Place the cargo so that its weight is distributed evenly between the front and rear axles.
Page 240: Floor Mat
Floor mat If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then dur- ing the trip to make sure the cargo remains in its place. Do not exceed 70 kg (154 lb.) cargo weight on the roof luggage carrier.
Page 241: Coat Hooks
Coat hooks To use the coat hook, push the hook. CAUTION Do not hook a hanger, heavy or sharp pointed object on the coat hook. If curtain shield airbags inflate, those items will be hurled away with great force or the curtain shield air- bags may not active correctly.
Page 243 INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Off−road vehicle precautionss .......
Page 244: Off−Road Vehicle Precautionss
Off−road vehicle precautions This vehicle belongs to the utility ve- CAUTION hicle class, which has higher ground clearance and narrower tread in relation Always observe the following precau- to the height of its center of gravity to tions to help minimize the risk of se- make it capable of performing in a wide rious personal injury or damage to variety of off−road applications.
Page 245: Break−In Period
To help prevent gas station mix−ups, your hicle more sensitive side to the future economy and long life of Toyota has a smaller fuel tank opening. winds than an ordinary passenger your vehicle: The special nozzle on pumps with un- car. Slowing down will allow you Avoid full−throttle...
Page 246 10% ethanol or 15% If you detect heavy knocking even when Automotive manufacturers in the U.S., MTBE. If you use gasohol in your Toyota, using the recommended fuel, or if you Europe and Japan have developed a...
Page 247: Fuel Pump Shut Off System
Operation in foreign countries The fuel pump shut off system stops sup- GASOLINE QUALITY If you plan to drive your Toyota in plying fuel to the engine when the engine another country... In a very few cases, you may experience stalls or an airbag inflates upon collision.
Page 248: Three−Way Catalytic Converter
The three−way catalytic converter is the z Use only unleaded gasoline. vehicle in for a check−up as soon emission control devices installed in as possible. Remember, your Toyota z Do not drive with an extremely low the exhaust system. dealer knows your vehicle and its fuel level;...
Page 249: Engine Exhaust Cautions
It gases to be drawn into the vehicle. Toyota Maintenance Schedule. For can cause unconsciousness or even To allow proper operation of your scheduled maintenance information, death.
Page 250: Facts About Engine Oil Consumption
(1.1 qt./600 miles, 0.9 Imp.qt/600 regularly. Toyota recommends that the oil by the high temperature combustion miles) level be checked every time you refuel gases during the combustion process.
Page 251: Iridium−Tipped Spark Plugs
Do not adjust gaps for engine perfor- mance or smooth drivability. properly. If they do not work well, depress the brake pedal firmly. If the brake system warning light comes on, immediately stop your vehicle and contact your Toyota deal-...
Page 252 The brake system warning light may stay Depressing the brake pedal on slippery ANTI−LOCK BRAKE SYSTEM on for about 60 seconds after the ignition road surfaces such as on a manhole cov- (with “ABS” warning light) key is turned to “ON” position. It is nor- er, a steel plate at a construction site, The anti−lock brake system is designed mal if the light turns off after a while.
Page 253 CAUTION Anti−lock brake system is not de- signed to shorten the stopping dis- overestimate anti−lock tance: Always drive at a moderate brake system: Although the anti−lock speed and maintain a safe distance brake system assists in providing ve- from the vehicle in front of you. hicle control, it is still important to Compared with vehicles without an drive with all due care and maintain...
Page 254 Toyota dealer. When the “ABS” warning light is on (and Have your Toyota dealer perform the bed- the brake system warning light is off), the In this case, not only the anti−lock ding−down.
Page 255: Brake Pad Wear Limit Indicators
Toyota CAUTION dealer as soon as possible. Expensive ro- tor damage can result if the pads are not Do not allow more than one person replaced when necessary. to get on the rear step bumper at a time.
Page 256: Limited−Slip Differential
This is the primary identification number Use only a spare tire of the same for your Toyota. It is used in registering size, construction and load capacity the ownership of your vehicle. as the original tires on your Toyota because damage to the limited−slip...
Page 257: Theft Prevention Labels
—Engine number Theft prevention labels Suspension and chassis Your new vehicle carries theft preven- CAUTION tion labels which are approximately 47 mm (1.85 in.) by 12 mm (0.47 in.) or 56 Do not modify the suspension/chassis mm (2.20 in.) by 16 mm (0.63 in.). with lift kits, spacers, springs, etc.
Page 258: Tire Information
Tire information— —Tire symbols This illustration indicates typical tire symbols. 1. Tire size—For details, see “Tire size” on page 250. 2. DOT Tire Identification Number (TIN)—For details, see “DOT and Tire Identification Num- ber (TIN)” on page 249. 3. Tire ply composition and materi- als—Plies mean a layer of rubber−...
Page 259 —DOT and Tire Identification Number (TIN) The “DOT” symbol certifies that the 7. “TUBELESS” or “TUBE TYPE” —A tubeless tire does not have a tire conforms to applicable Federal tube inside the tire and air is direct- Motor Vehicle Safety Standards. ly filled in the tire.
Page 260 —Tire size —Name of each section of tire 20c506a 21A007a 21A006a This illustration indicates typical tire 1. Section width 1. Bead size. 2. Tire height 2. Sidewall 1. Tire (P=Passenger car, 3. Wheel diameter 3. Shoulder T=Temporary use) 4. Tread 2.
Page 261 150 would wear conditions on specified government purchasers of Toyota vehicles with in- one and a half (1−1/2) times as well test surfaces of asphalt and concrete. formation on uniform tire quality grad-...
Page 262 Temperature A, B, C—The tempera- ture grades are A (the highest), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 263 —Glossary of tire terminology Tire related term Meaning tire inflation pressure when the vehicle has been parked for at least 3 hours or more, or it has not been driven more than 1.5 km or 1 mile under that Cold tire inflation pressure condition the maximum cold inflation pressure to which a tire may be inflated and it is Maximum inflation pressure...
Page 264 Tire related term Meaning the combined weight of those installed regular production options weighing over 2.3 kg (5 lb.) in excess of those standard items which they replace, not pre- Production options weight viously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim Vehicle capacity weight the rated cargo and luggage load plus 68 kg (150 lb.) times the vehicle’s desig-...
Page 265 Tire related term Meaning the load on an individual tire that is determined by distributing to each axle Vehicle normal load on the tire its share of the curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1 that follows) and dividing by two Weather side the surface area of the rim not covered by the inflated tire Table 1–...
Page 266: Vehicle Load Limits
Vehicle load limits Vehicle load limits include total load NOTICE CAUTION capacity, seating capacity, towing ca- pacity and cargo capacity. Follow the Even if the number of occupants Do not apply the load more than load limits shown below. Total load ca- are within the seating capacity, each load limit.
Page 267: Cargo And Luggage
Cargo and luggage— —Stowage precautions When stowing cargo and luggage in D Never allow anyone to ride in NOTICE or on the vehicle, observe the follow- the luggage compartment. It is ing: Do not load the vehicle beyond not designed for passengers. D Put cargo and luggage in the lug- the vehicle capacity weight giv- They should ride in their seats...
Page 268 —Capacity and distribution (4) The resulting figure equals the Cargo capacity depends on the to- available amount of cargo and tal weight of the occupants. luggage load capacity. For exam- (Cargo capacity) = (Total load capac- ple, if the “XXX” amount equals ity) –...
Page 269 379 kg – 176 kg = 203 kg. CAUTION (834 lb. – 388 lb. = 446 lb.) Weight of removed As shown in the above example, if the third seat Even if the total load of occu- number of occupants increases, the pant’s weight and the cargo load Cargo cargo and luggage load equaling the...
Page 270: Types Of Tires
Types of tires All season tires, however, do not have Determine what kind of tires your adequate traction performance vehicle is originally equipped with. compared with snow tires in heavy or 1. Summer tires loose snow. Also, all season tires fall Summer tires are high−speed capabil- short in acceleration and handling ity tires best suited to highway driving...
Page 271 SECTION STARTING AND DRIVING Starting and driving Before starting the enginee ........How to start the engine .
Page 272: Before Starting The Enginee
How to start the engine— (a) Cranking hold function Before starting the engine (b) Before cranking 1. Check the area around the vehicle be- Once you turn the ignition key to “START” 1. Apply the parking brake firmly. fore entering it. position and release it, the cranking hold 2.
Page 273: Tips For Driving In Various Conditions
To dry them, drive vehicle cautiously while lightly pressing the brake pedal with the park- ing brake applied. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.
Page 274: Off−Road Driving Precautions
Off−road driving precautions When driving your vehicle off−road, please CAUTION Do not drive in excess of the speed observe the following precautions to en- sure your driving enjoyment and to help limit. Even if the legal speed limit Before driving off, make sure the permits it, do not drive over 140 prevent the closure of areas to off−road vehicles.
Page 275 U.S. Forest Service and Bureau of NOTICE Land Management After driving through tall grass, mud, rock, sand, rivers, etc., check z If driving through water, such as that there is no grass, bush, paper, CAUTION when crossing shallow streams, rags, stone, sand, etc. adhering or first check the depth of the water trapped on the underbody.
Page 276: Winter Driving Tips
Guide” or “Owner’s Manual selection. Leaving a heavy summer oil in your ve- Supplement”. “Toyota Super Long Life Coolant” is a mix- hicle during winter months may cause ture of 50% coolant and 50% deionized harder starting. If you are not sure about water.
Page 277: Dinghy Towing
When parking, put the transmission into overload your vehicle or trailer. Ask your “P” and block the front wheels. Do not local Toyota dealer for further details be- use the parking brake, or snow or water fore towing. accumulated in and around the parking...
Page 278 WEIGHT LIMITS CAUTION Trailer hitch assemblies have differ- Before towing, make sure the total trail- ent weight capacities established by er weight, gross combination weight, The maximum gross trailer weight the hitch manufacturer. Even though gross vehicle weight, gross axle weight (trailer weight plus cargo weight) the vehicle may be physically capa- and trailer tongue load are all within...
Page 279 Total trailer weight Tongue load The load on either the front or rear axle resulting from distribution of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label. 20c508a Tongue load ∗...
Page 280 Never load the trailer with more If you wish to install a trailer hitch, you weight in the back than in the should consult with your Toyota dealer. Do not use axle−mounted hitches as front. About 60% of the trailer load...
Page 281 Trailer Class Typical Trailer Ball Size 2 in. 2 in. 1 7/8 in. 2. Select the appropriate trailer ball to match exceed gross trailer weight rating of the trailer. The trailer ball load rating should be printed on the top of the ball. 3.
Page 282 Never tap into your vehicle’s hy- BRAKES AND SAFETY CHAINS Rear 240 (35) draulic system as it would lower its See Section 7−2 and Section 8 for in- Toyota recommends trailers with braking effectiveness. brakes that conform to any applica- structions.
Page 283 3. Turn the ignition switch on or push the BREAK−IN SCHEDULE height control switch to turn on the Toyota recommends that you do not active height control suspension. Select tow a trailer with a new vehicle or a the “N” (normal) mode with the height vehicle with any new power train com- select switch.
Page 284 4. Turn the ignition switch on or push the Check that your rear view mirrors con- Avoid jerky starts or sudden accelera- height control switch to turn on the form to any applicable federal, state/ tion. active height control suspension. provincial or local regulations.
Page 285 Crosswinds and rough roads will ad- Because of the added load of the trail- When restarting out after parking on a versely affect handling of your vehicle er, your vehicle’s engine may overheat slope: and trailer, causing sway. Pay attention on hot days temperatures over 1.
Page 286: How To Save Fuel And Make Your Vehicle Last Longer, Too
How to save fuel and make your vehicle last longer, too Improving fuel economy is easy–just take Use a Avoid engine over-revving. CAUTION it easy. It will help make your vehicle last gear position suitable for the road on longer, too. Here are some specific tips which you are travelling.
Page 287 Keep front wheels in proper alignment. Avoid hitting the curb and CAUTION slow down on rough roads. Improper Never turn off the engine to coast alignment not only causes faster tire wear but also puts an extra load on down hills. Your power steering and the engine, which, in turn, wastes fuel.
Page 289 SECTION IN CASE OF AN EMERGENCY In case of an emergency If your vehicle will not startt ........If your engine stalls while driving .
Page 290: If Your Vehicle Will Not Startt
2. If the engine still will not start, it needs work, your key may be broken. Have the adjustment or repair. Call a Toyota key checked at your Toyota dealer. If 3. If the light is out, dim or goes out dealer or qualified repair shop.
Page 291 If the engine still will not start, it needs which is poisonous and corrosive. adjustment or repair. Call a Toyota dealer Wear protective safety glasses when or qualified repair shop for assistance. jump starting, and avoid spilling acid on your skin, clothing, or ve- hicle.
Page 292 JUMP STARTING PROCEDURE 1. If the booster battery is installed in Discharged battery Jumper cable another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories. Booster When boosting, use the battery of battery matching or higher quality.
Page 293 If the cause of your battery discharging is not apparent (for example, lights left on), When making connections, you should have it checked at your Toyota avoid serious injury, do not lean over dealer. the battery or accidentally let the jumper cables or clamps touch any- thing except the correct battery termi- nals or the ground.
Page 294: If Your Engine Stalls While Driving
CAUTION After arriving at a safe place, stop the vehicle and call a Toyota dealer for 2. If coolant or steam is boiling out of the If the engine is not running, the pow- assistance.
Page 295: If You Have A Flat Tire
You should have it checked as 4. If the engine drive belt is broken or the soon as possible at your Toyota dealer. 5. Read the following instructions coolant is leaking, stop the engine im- mediately.
Page 296 D Make sure to set the jack prop- NOTICE CAUTION erly in the jack point. Raising z Do not continue driving with When jacking, be sure to observe the vehicle with jack improper- a deflated tire. Driving even a the following to reduce the possi- ly positioned will damage the short distance can damage a bility of personal injury:...
Page 297 —Required tools and spare tire Turn the jack joint by hand. To remove the spare tire under the 1. Get the required tools and spare luggage compartment: tire. To remove: Turn the joint in direction 1 Tool bag 1 until the jack is free. 1.
Page 298 When connecting a jack handle exten- 2. Remove the access hole cover on 3. Insert the jack handle end into the sion with a jack handle end, use a the rear bumper with a flathead lowering screw through the access jack handle to tighten the bolts on the screwdriver.
Page 299 —Blocking the wheel 4. After the tire is lowered completely When storing the spare tire, put it in 2. Block the wheel diagonally op- to the ground, remove the holding place with the outer side of the wheel posite the flat tire to keep the bracket as shown in the illustration.
Page 300 —Removing wheel ornament —Loosening wheel nuts CAUTION Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, which could cause a serious ac- cident. 3. Remove the wheel ornament. 4.
Page 301 —Positioning the jack JACK POINTS: Front—Under the frame side rail Left rear—Under the rear axle housing Right rear—Under the bracket on the rear axle housing Make sure the jack is positioned on a level and solid place. Put a jack handle, jack handle exten- sions, and jack handle end together as shown in the illustration.
Page 302 —Raising your vehicle NOTICE Tighten all the joints securely. Otherwise, the extension may come off and it may damage the paint or vehicle body. When connecting a jack handle exten- 6. After making sure no one is in sion with another extension and a jack the vehicle, raise it high enough handle end, use a jack handle to tight- so that the spare tire can be...
Page 303 —Changing wheels To raise the vehicle, insert the jack handle end into the joint of the jack (it is a loose fit) and turn it clockwise with the handle, making sure the han- dle remains firmly fitted onto the jack handle extension.
Page 304 —Reinstalling wheel nuts —Lowering your vehicle CAUTION Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and damaging the bolts. The nuts may loosen and the wheels may fall off, which could cause a seri- ous accident.
Page 305 —Reinstalling wheel ornament Tighten each nut a little at a time in CAUTION the order shown. Repeat the process until all the nuts are tight. D Take due care in handling the ornament to avoid unexpected CAUTION personal injury. D When lowering the vehicle, D Do not attach a heavily dam- make sure all portions of your aged plastic wheel ornament.
Page 306: If Your Vehicle Becomes Stuck
If your vehicle becomes stuck —After changing wheels If your vehicle becomes stuck in snow, 11. Check the air pressure of the re- CAUTION mud, sand, etc., then you may attempt to placed tire. rock the vehicle free by moving it forward Adjust the air pressure to the specifi- and backward.
Page 307: If Your Vehicle Needs To Be Towed
If towing is necessary, we recommend NOTICE (a) Towing with wheel lift type truck— you have it done by your Toyota dealer or a commercial tow truck service. In —From front If you rock your vehicle, observe the consultation with them, have your ve- following precautions to prevent dam- hicle towed using either (a) or (b).
Page 308 “Active height control suspension” on page 167. (c) Towing with sling type truck If towing is necessary, we recommend you to have it done by your Toyota (a) Towing with wheel lift type truck NOTICE dealer or a commercial tow truck ser- Use a towing dolly under the wheels not vice.
Page 309 —Emergency towing hook precautions Before emergency towing, check that CAUTION CAUTION the hook is not broken or damage and that the installation bolts are not loose. Use extreme caution when towing ve- If the engine is not running, the pow- Fasten the towing cable or chain se- hicle.
Page 310: If You Cannot Shift Automatic Transmission Selector Lever
If the towing vehicle can hardly move, do not forcibly continue the If you cannot shift the selector lever towing. Contact your Toyota dealer out of “P” position to other positions or a commercial tow truck service even though the brake pedal is de- for assistance.
Page 311: If You Lose Your Keys
Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced.
Page 313 APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosionn ..... . . Washing and waxing your Toyota .
Page 314 Now, it is up to be dry. to see all the mud and dirt. It will do you. Proper care of your Toyota can help more harm than good to simply wet the High ambient temperatures can cause ensure long−term corrosion prevention.
Page 315 Washing and waxing your Toyota Check the interior of your vehicle. Wa- Washing your Toyota ter and dirt can accumulate under the Exhaust gases cause the exhaust Keep your vehicle clean by regular floor mats and could cause corrosion. Oc- pipe to become quite hot.
Page 316 Toyota dealer to your vehicle. have the vehicle serviced. NOTICE NOTICE To prevent damage to the antenna, If a nozzle becomes blocked, do not...
Page 317 Cleaning the interior Exterior lights: Do not apply wax on the Vinyl interior surfaces of the lights. Wax may cause CAUTION The vinyl upholstery may be easily damage to the lenses. If you accidentally cleaned with a mild soap or detergent Vehicles with side airbags and cur- put wax on the light surfaces, wipe or and water.
Page 318 Carpets NOTICE NOTICE Use a good foam−type shampoo to z Do not use dye or bleach on the z Do not use organic substances (sol- clean the carpets. belts—it may weaken them. vents, kerosene, alcohol, gasoline, Begin by vacuuming thoroughly to remove etc.) or alkaline or acidic solutions.
Page 319 If you have any questions about the leather these could cleaning of your Toyota, your local cause discoloring. Toyota dealer will be pleased to answer them. z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.
Page 321 SECTION VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirementss ....... . . General maintenance .
Page 322: Maintenance Requirementss
Section 7. dating this warranty. See “Owner’s War- or if you prefer, your Toyota dealer will be ranty Information Booklet” or “Owner’s pleased to do them at a nominal cost.
Page 323: General Maintenance
Radiator, condenser and hoses Supplement” for the details. vehicle to your Toyota dealer or a quali- Check that the front of the radiator and fied service shop immediately. It is recom- condenser are clean and not blocked with mended that any problem you notice be leaves, dirt, or insects.
Page 324 Exhaust system Seats Parking brake If you notice any change in the sound of Check that all front seat controls such as Check that the lever has the proper travel the exhaust or smell exhaust fumes, have seat adjusters, seatback recliner, etc. op- and that, on a safe incline, your vehicle the cause located and corrected immedi- erate smoothly and that all latches lock...
Page 325: Does Your Vehicle Need Repairing
If you notice any of these clues, take your tant clues are as follows: month. See page 330 for additional vehicle to your Toyota dealer as soon as information. Engine missing, stumbling, or pinging possible. It probably needs adjustment or repair.
Page 326: Emissions Inspection And Maintenance (I/M) Programs
Toyota dealer comes on. In this case, your vehicle may to prepare the vehicle for re−testing. not pass the I/M test and need to be repaired.
Page 327 SECTION − DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview ....... Fuse locations .
Page 328: Engine Compartment Overview
Engine compartment overview 1. Suspension fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Fuse block 5. Battery 6. Windshield and rear window washer fluid tank 7. Engine oil level dipstick 8. Condenser 71C004f 9. Radiator 10. Engine coolant reservoir 11.
Page 329: Fuse Locations
Fuse locations Spare fuses i71002d Spare fuses 71C510a...
Page 330: Do−It−Yourself Service Precautions
Right after driving, engine warranty coverage. Read separate automatically start to run if the air compartment—the engine, radiator, Toyota Warranty statement for details and conditioning is on. exhaust manifold, power steering suggestions. Use eye protection whenever you fluid reservoir spark...
Page 331: Parts And Tools
Remember all Toyota parts are de- trode. Do not dispose of used oil and fil- signed in metric sizes, so your tools must...
Page 332 Tools: CHECKING AND REPLACING FUSES Funnel (only for adding coolant) Parts (if replacement is necessary): Fuse with same amperage rating as CHECKING BRAKE FLUID original Parts (if level is low): ADDING WASHER FLUID SAE J1703 or FMVSS No.116 DOT 3 brake fluid Parts: Water...
Page 333 SECTION − DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level ....... . . Checking the engine coolant level .
Page 334: Checking The Engine Oil Level
Checking the engine oil level Low level NOTICE Full level Be careful not to drop engine oil on the vehicle components. If the oil level is below or only slightly above the low level, add engine oil of the same type as already in the engine. Remove the oil filler cap and add engine oil in small quantities at a time, checking Add oil...
Page 335 ENGINE OIL SELECTION SAE 5W−30 is the best choice for good fuel economy, and good starting in cold “Toyota Genuine Motor Oil” is used in weather. your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent If SAE 5W−30 oil is not available, SAE to satisfy the following grade and viscos- 10W−30 oil may be used.
Page 336: Checking The Engine Coolant Level
Toyota engines. Do not use plain water alone. If you can find no leak, have your Toyota Please contact your Toyota dealer for fur- dealer test the cap pressure and check ther details about “Toyota Genuine Motor for leaks in the cooling system.
Page 337: Checking The Radiator And Condenser
If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer. CAUTION To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.
Page 338: Checking Brake Fluid
Checking brake fluid If the level is low, add SAE J1703 or NOTICE FMVSS No. 116 DOT 3 brake fluid to the brake reservoir. Only use the Suspension fluid AHC for the active height control suspen- Refilling brake fluid: sion. If you fill other fluids such as 1.
Page 339: Checking Power Steering Fluid
Checking power steering fluid Clean all dirt from outside of the reservoir NOTICE tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” If cold If you spill some of the fluid, be sure range.
Page 340: Checking Tire Inflation Pressure
Checking tire inflation pres- sure CAUTION The reservoir may be hot so be care- ful not to burn yourself. NOTICE Avoid overfilling, or the power steer- ing could be damaged. 72c502b Type A Type B...
Page 341 D Always use a tire inflation pres- Keep your tire inflation pressures Tire inflation sure gauge. The appearance of at the proper level. pressure gauge a tire can be misleading. Besides, The recommended cold tire inflation tire inflation pressures that are pressures, tire sizes and the com- even just a few pounds off can de- bined weight of occupants and cargo...
Page 342 D A greater possibility of tire waste fuel, reduce the comfort of driv- damage from road hazards ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal-...
Page 343: Checking And Replacing Tires
Checking and replacing tires The tires on your Toyota have built−in If air loss occurs while driving, do not Tread wear indicator tread wear indicators to help you continue driving. Driving even a short know when the tires need replace- distance can damage a tire beyond ment.
Page 344 Using any other size or type of tire Toyota recommends all four tires, CAUTION may seriously affect handling, ride, or at least both front or rear tires speedometer/odometer calibration, be replaced as a set. Observe the following instruc- ground clearance, and clearance be- See “If you have a flat tire”...
Page 345: Rotating Tires
To equalize tire wear and help ex- Do not use tires other than those men- tend tire life, Toyota recommends tioned above. Do not install studded tires that you rotate your tires accord- without first checking local regulations for ing to the maintenance schedule.
Page 346 SNOW TIRE INSTALLATION CAUTION Side chain Snow tires should be installed on all wheels. Observe following instructions. Installing snow tires on the rear wheels Otherwise, an accident may occur re- only can lead to an excessive difference sulting in death or serious injuries. in road grip capability between the front Do not use snow tires other than and rear tires which could cause loss of...
Page 347: Replacing Wheels
When installing chains on your tires, care- Correct replacement wheels are available When driving with chains installed, fully follow the instructions of the chain at your Toyota dealer. be sure to drive carefully. Slow manufacturer. down before...
Page 348: Aluminum Wheel Precautions
Otherwise, an accident may occur re- sulting in death or serious injuries. When balancing your wheels, use only Toyota balance weights or equivalent Do not use wheels other than the and a plastic or rubber hammer. manufacturer’s recommended size,...
Page 349 SECTION − DO-IT-YOURSELF MAINTENANCE Electrical components Checking battery condition ........Battery recharging precautions .
Page 350: Checking Battery Condition
Checking battery condition— —Precautions —Checking battery exterior Ground cable CAUTION If electrolyte gets on your skin, Terminals thoroughly wash the contact area. If BATTERY PRECAUTIONS you feel pain or burning, get medi- cal attention immediately. The battery produces flammable and explosive hydrogen gas.
Page 351: Battery Recharging Precautions
To return the moon roof to normal, Have battery Dark White see “Electric moon roof” on page 31. checked by your NOTICE Toyota dealer. Clear or Have battery Never recharge the battery while the light checked by your engine is running. Also, be sure all accessories are turned off.
Page 352: Checking And Replacing Fuses
Checking and replacing fuses Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. Type A If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good.
Page 353: Adding Washer Fluid
When replacing er tank may be empty. Add washer tem. Have your Toyota dealer correct it as a bulb, make sure the ignition switch and fluid. soon as possible.
Page 354 Hold a bulb pooled inside light, contact your Interior lights only by its plastic or metal case. — Toyota dealer. Do not touch the glass part of a Personal lights bulb with bare hands. Type A — Bulb Light bulbs Type Type B —...
Page 355 —Headlights 73c005a 1. Open the hood. 2. Left−hand headlight and right−hand 3. Pull the bulb out of the bulb base. head light (high beam): If the connector is tight, wiggle it. Left−hand headlight: Remove Turn the bulb base counterclockwise washer inlet. to the front of the vehicle.
Page 356 Right−hand headlight (low beam): Install the bulb base by turning it counterclockwise to the front of the vehicle. Left−hand headlight: Remove washer inlet. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 357 Use a flathead screwdriver. 3. Install a new bulb base by turning it clockwise to the front of the vehicle. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 358 —License plate lights a: Rear turn signal light b: Back–up light...
Page 359 SECTION SPECIFICATIONS Specifications Dimensions and weightss ........Engine .
Page 360: Dimensions And Weightss
Dimensions and weights Engine Fuel Overall length mm (in.) 4890 (192.5) Model: Fuel type: 4.7L V8 (2UZ−FE) Unleaded gasoline, Octane Rating 87 Overall width mm (in.) 1940 (76.4) (Research Octane Number 91) or higher. Type: ∗ 1 Overall height mm (in.) 1875 (73.8) 8 cylinder V type, 4 cycle, gasoline Fuel tank capacity, L (gal., Imp.gal.):...
Page 361: Service Specifications
Coolant type: DENSO SK20R11 “Toyota Super Long Life Coolant” is used IFR6A11 in your Toyota vehicle at factory fill. In Spark plug gap, mm (in.): order to avoid technical problems, only use 1.1 (0.043) “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−sili-...
Page 362 No.2 or Molybdenum—disulfide lithium Hypoid gear oil API GL−5 changing automatic transmission base chassis grease, NLGI No.2 fluid, use only “Toyota Genuine ATF Recommended oil viscosity: WS” (ATF JWS3324 or NWS9638) to aid Above –18_C (0_F) in assuring maximum transmission per- SAE 90 formance.
Page 363 BRAKES Minimum pedal clearance when depressed with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.): 116 (4.6) Pedal free play, mm (in.): 1 – 6 (0.04 – 0.24) Pad wear limit, mm (in.): 1.0 (0.04) Lining wear limit, mm (in.): 1.0 (0.04)
Page 364: Tires
Tires Tire size and inflation pressure: kPa (psi) Front Rear Spare Tire size Wheel size Normal Trailer Normal Trailer Normal Trailer driving towing driving towing driving towing 220 (32) 240 (35) P275/60R18 111H 200 (29) 220 (32) 220 (32) 240 (35) Wheel nut torque, N·m (kgf·m, ft·lbf): 131 (13.4, 96.6) NOTE: For complete information on tires (e.g.
Page 365: Fuses
Fuses Engine compartment Left side kick panel Right side kick panel Emergency flashers, All components in “ECU−B2” Fuses 8. HAZ−TRN 15 A: 18. BAT 30 A: Turn signal lights 1. ABS NO.2 40 A: Anti−lock brake sys- No circuit 19. TEL 7.5 A: Charging system 9.
Page 366 52. DIFF 20 A: Four−wheel drive system Active height control sus- 34. AHC−B 15 A: pension (AHC) 53. WASHER 15 A: Windshield washer Fuel heater 35. FUEL HTR 20 A: 54. RADIO 10 A: Audio system Power heater 36. POWER HTR 7.5 A: 55.
Page 367 70. RR A/C 30 A: Rear air conditioning system 71. RH SEAT 30 A: Power seat system 72. AIR PUMP 50A: Multiport fuel injection system/Sequential multiport fuel injec- tion system 73. A/F HTR 15A: Multiport fuel injection system/Sequential multiport fuel injec- tion system...
Page 369 SECTION REPORTING SAFETY DEFECTS FOR U.S. OWNERS AND UNIFORM TIRE QUALITY GRADING Reporting safety defects for U.S. owners and uniform tire quality grading Reporting safety defects for U.S. ownerss ....
Page 370 However, NHTSA cannot become involved in individual prob- lems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.
Page 371 U −8 Quick index D If a service reminder indicator or warning buzzer comes on ..D If your vehicle will not start ........D If your engine stalls while driving .
Page 372 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
Page 373 The repair manual outlines exactly what main- The repair manual for LAND CRUISER may be tenance is required and clearly explains how to do the purchased from any Toyota dealer or the Mate- work yourself step−by−step. rial Distribution Center. To purchase the repair...
Page 374 WE REALLY CARE ABOUT YOU PLEASE BUCKLE UP Toyota has made a special effort to encourage use of seat belts. Toyota belts are: Comfortable Easy to use Convenient We encourage you to use your belts every time you drive.

Toyota Land Cruiser 2006 Owner's Manual

2 Section −

3 Section −

4 Section −

5 Section −

6 Section −

7 Section −

8 Section −

9 Section −

10 Section −

Section

Section

Section

Section

1 Section −

2 Section −

Quick Links

Chapters

Related Manuals for Toyota Land Cruiser 2006

Summary of Contents for Toyota Land Cruiser 2006

Table of Contents